28.12.2012 Views

z/VM: System Messages and Codes Š CP - z/VM - IBM

z/VM: System Messages and Codes Š CP - z/VM - IBM

z/VM: System Messages and Codes Š CP - z/VM - IBM

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

not fill up the error log or flood the operator’s console<br />

with messages.<br />

<strong>System</strong> Action: Normal system operation continues,<br />

but without reporting system recovery errors.<br />

Operator Response: If system recovery errors have<br />

not been too frequent, <strong>and</strong> you do want to have them<br />

reported to you <strong>and</strong> recorded in the error log in the<br />

future, enter the SET MODE comm<strong>and</strong>, as follows, to<br />

enable reporting of system recovery errors once again:<br />

SET MODE RECORD<br />

H<strong>CP</strong>9108E UNEXPECTED ERROR. POSSIBLY<br />

CAUSED BY SOFTWARE.<br />

Explanation: A condition that normally produces an<br />

abend has occurred, but it occurred in the<br />

machine-check h<strong>and</strong>ler, where an abend cannot be<br />

safely issued. Therefore, system termination is being<br />

initiated directly from the machine-check h<strong>and</strong>ler rather<br />

than from the abend processor.<br />

<strong>System</strong> Action: The system stops. An automatic<br />

software re-IPL will not follow this termination.<br />

Operator Response: Notify your system support<br />

personnel.<br />

H<strong>CP</strong>9109I <strong>System</strong> operation continues.<br />

Explanation: The machine check that message<br />

H<strong>CP</strong>9101I describes, or the check-stop that message<br />

H<strong>CP</strong>610I describes, has been h<strong>and</strong>led successfully.<br />

<strong>System</strong> termination was not required.<br />

<strong>System</strong> Action: <strong>System</strong> operation continues. If the<br />

error was a check-stop, the failed processor will soon<br />

be varied offline. If the error was a machine check, the<br />

failed processor may or may not be varied offline,<br />

depending on the severity of the error.<br />

Operator Response: None.<br />

H<strong>CP</strong>9110I Reporting will be suspended<br />

temporarily because machine checks<br />

are occurring too frequently.<br />

Explanation: In the past few minutes, machine checks<br />

have occurred frequently. In order to avoid tying up the<br />

console with error messages, machine-check reporting<br />

is being suspended for a few minutes. Recording these<br />

errors in the error log for <strong>CP</strong>EREP is also suspended.<br />

The suspension is selective. New types of errors are<br />

still reported <strong>and</strong> recorded. Also, the suspension is only<br />

temporary. In a few minutes the system returns<br />

(unannounced) to normal operation unless the frequent<br />

errors persist.<br />

<strong>System</strong> Action: Normal operation of the system<br />

continues, but fewer errors are being reported.<br />

Operator Response: If the problem persists, contact<br />

your system support personnel.<br />

Programmer Response: Contact your <strong>IBM</strong> Support<br />

Center personnel to diagnose <strong>and</strong> correct the hardware<br />

problem.<br />

H<strong>CP</strong>9111I An exp<strong>and</strong>ed storage error has<br />

occurred.<br />

Explanation: A machine check occurred in exp<strong>and</strong>ed<br />

storage, or, an exp<strong>and</strong>ed storage operation returned a<br />

non-zero condition code.<br />

<strong>System</strong> Action: <strong>System</strong> operation continues.<br />

Operator Response: This is probably a hardware<br />

error. If you need assistance, contact your <strong>IBM</strong><br />

representative.<br />

H<strong>CP</strong>9150E A(n) {equipment|receiver} check has<br />

occurred because the signalling facility<br />

for processor nn is damaged.<br />

Explanation: A SIGP SENSE showed either an<br />

equipment check or a receiver check. These checks<br />

indicate that the signal has failed. The unresponsive<br />

processor detection function detected this situation.<br />

<strong>System</strong> Action: The message is repeated every ten<br />

seconds until the condition is corrected or the failing<br />

processor is varied offline.<br />

User Response: None.<br />

Operator Response: Contact your <strong>IBM</strong> Support<br />

Center personnel to diagnose <strong>and</strong> correct the hardware<br />

problem.<br />

H<strong>CP</strong>9151E Processor nn {has stopped|operator is<br />

intervening.}<br />

Explanation: The unresponsive processor detection<br />

function has detected a processor that is unresponsive<br />

because of an OPERATOR INTERVENING or<br />

STOPPED condition.<br />

<strong>System</strong> Action: The message is repeated every ten<br />

seconds until the condition is corrected.<br />

User Response: None.<br />

Operator Response: Start the processor if the<br />

STOPPED condition is indicated. For OPERATOR<br />

INTERVENING, stop doing whatever is causing the<br />

intervention to be detected.<br />

H<strong>CP</strong>9152E Processor nn is being varied offline<br />

because it is not responsive.<br />

Explanation: The unresponsive processor detection<br />

function has determined that a processor is<br />

unresponsive.<br />

<strong>System</strong> Action: The unresponsive processor is varied<br />

offline.<br />

User Response: None.<br />

H<strong>CP</strong>9108E H<strong>CP</strong>9152E<br />

Chapter 3. <strong>System</strong> <strong>Messages</strong> 461

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!