z/VM: System Messages and Codes Š CP - z/VM - IBM
z/VM: System Messages and Codes Š CP - z/VM - IBM
z/VM: System Messages and Codes Š CP - z/VM - IBM
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
H<strong>CP</strong>6260I H<strong>CP</strong>6268E<br />
H<strong>CP</strong>6260I The Channel-Path-Measurement<br />
Facility encountered a recoverable<br />
error. <strong>VM</strong> is awaiting channel<br />
subsystem recovery.<br />
Explanation: The Channel-Path-Measurement Facility<br />
encountered a recoverable error.<br />
<strong>System</strong> Action: The Channel-Path-Measurement<br />
Facility is stopped. The facility will be restarted<br />
automatically when channel subsystem recovery is<br />
complete. In the interim, there will be no updates to the<br />
channel measurement data reported in Monitor records.<br />
Operator Response: None.<br />
H<strong>CP</strong>6261I The Channel-Path-Measurement<br />
Facility was successfully restarted.<br />
Explanation: The Channel-Path-Measurement Facility<br />
was successfully restarted after a recoverable error was<br />
detected.<br />
<strong>System</strong> Action: The Channel-Path-Measurement<br />
Facility is restarted.<br />
Operator Response: None.<br />
H<strong>CP</strong>6262E value is an invalid time limit for<br />
monitor {event|sample} CONFIG.<br />
Explanation: The value specified for CONFIG LIMIT<br />
on the MONITOR SAMPLE/EVENT comm<strong>and</strong> is invalid.<br />
This message is generated when one of the following is<br />
true:<br />
v A nonnumeric value was specified.<br />
v The CONFIG value is less than the minimum value or<br />
greater than the maximum value required as<br />
documented for the MONITOR CONFIG LIMIT<br />
comm<strong>and</strong>.<br />
<strong>System</strong> Action: The comm<strong>and</strong> is rejected.<br />
User Response: Reenter the comm<strong>and</strong> with a valid<br />
value.<br />
H<strong>CP</strong>6265A Monitor writer connected to iucvserver<br />
action<br />
Explanation: Monitor writer has connected with the<br />
specified iucvserver. The writer will transfer any monitor<br />
data collected to the output file until it is stopped, using<br />
either the #<strong>CP</strong> EXTERNAL or MONWSTOP comm<strong>and</strong>.<br />
Note: The following message text appears only if no<br />
monitoring is active when the monitor writer<br />
connects to *MONITOR:<br />
action = START <strong>CP</strong> MONITOR.<br />
<strong>System</strong> Action: Monitor writer waits for<br />
communication from iucvserver to begin.<br />
Operator Response: If iucvserver is *MONITOR, <strong>and</strong><br />
362 z/<strong>VM</strong>: <strong>System</strong> <strong>Messages</strong> <strong>and</strong> <strong>Codes</strong> — <strong>CP</strong><br />
the <strong>CP</strong> monitor is not started, start the <strong>CP</strong> monitor by<br />
entering the <strong>CP</strong> MONITOR START, <strong>CP</strong> MONITOR<br />
EVENT START, or <strong>CP</strong> MONITOR SAMPLE START<br />
comm<strong>and</strong>.<br />
If iucvserver is not *MONITOR, follow startup<br />
procedures for that application.<br />
H<strong>CP</strong>6266A End-of-tape encountered for vdev<br />
mount <strong>and</strong> ready a new writable tape<br />
Explanation: The end of the tape has been reached<br />
by monitor writer for the vdev given.<br />
<strong>System</strong> Action: The tape on the real device<br />
associated with vdev is rewound <strong>and</strong> unloaded. If only<br />
one virtual device was specified or defaulted on the<br />
MONWRITE comm<strong>and</strong>, monitor writer waits for the new<br />
tape to be mounted. If two virtual devices were specified<br />
on the MONWRITE comm<strong>and</strong>, writing continues on the<br />
other tape device.<br />
User Response: If the tape device has an automatic<br />
tape loading feature (for example: the cartridge stacker<br />
loader on the <strong>IBM</strong> 3480), no action is required unless<br />
the stacker is empty. If there is no automatic loading<br />
feature or the stacker is empty, contact the operator <strong>and</strong><br />
request that a new tape be mounted on the real device<br />
associated with the virtual device given in the message.<br />
Operator Response: If the tape device has an<br />
automatic tape-loading feature (for example, the<br />
cartridge stacker loader on the <strong>IBM</strong> 3480), no action is<br />
required unless the stacker is empty. If there is no<br />
automatic loading feature or the stacker is empty, mount<br />
a new tape on the real device associated with the given<br />
virtual device. Make sure the tape can be written to.<br />
H<strong>CP</strong>6267I Monitor writer connection to iucvserver<br />
ended<br />
Explanation: Monitor writer has ended<br />
communications with the given IUCV server.<br />
<strong>System</strong> Action: Monitor writer continues termination<br />
activity.<br />
User Response: None.<br />
H<strong>CP</strong>6268E Attempt to connect to monitor writer<br />
by application has been severed<br />
Explanation: An attempt was made by application to<br />
make an IUCV connection to the monitor writer function.<br />
The connect attempt has been severed.<br />
<strong>System</strong> Action: Monitor writer continues operation.<br />
User Response: Contact the system programmer.<br />
Determine who attempted the connection. The<br />
application variable is probably a user ID. The<br />
application issued an IUCV CONNECT (probably using<br />
the IUCV macro or the CMSIUCV macro) that specified<br />
MONWRITE as the target of that connection. Change
Change language