z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP8601I HCP8609E
HCP8601I All SECTABLE file records were found
to be valid.
Explanation: The SECTABLE application program
reviewed the records in SECTABLE FILE and found
them to be correct.
System Action: None.
User Response: None.
HCP8602I SECLABEL/HRL correlation table has
been successfully stored.
Explanation: The DIAGNOSE X'A0' subcode X'34'
issued by the SECTABLE application program
successfully transferred an up-to-date working copy of
SECTABLE FILE to CP storage.
System Action: None.
User Response: None.
HCP8603E Invalid operand specification on
SECTABLE invocation.
Explanation: The user invoked the SECTABLE
application program incorrectly.
System Action: The system ignored the command.
User Response: There are only two valid ways to
invoke this program. Enter one of the following:
SECTABLE
SECTABLE STORE
HCP8604E Error from CMS macro macro with
return code retcode.
Explanation: The SECTABLE application program
invokes several CMS macros, including FSOPEN,
FSREAD, FSCLOSE, APPLMSG, ABNEXIT, and
CMSSTOR. An error occurred in the macro mentioned
in the message.
System Action: If the error occurred in the APPLMSG
macro, the system delivers erroneous output at the
console. If the error occurred in one of the other
macros, processing of the application is terminated.
User Response: See the entry for the macro in the
z/VM: CMS Callable Services Reference. You will find
the return code defined there.
HCP8605E SECTABLE FILE must have LRECL not
< 10, LRECL not > 141, and RECFM =
V.
Explanation: The logical record length or the record
format of SECTABLE FILE is incorrect.
System Action: The SECTABLE application program
was unable to use SECTABLE FILE in its present form,
and the application terminated.
450 z/VM: System Messages and Codes — CP
User Response: The LRECL value for SECTABLE
FILE must be from 10 to 141; its RECFM value must be
V. Make any necessary corrections.
HCP8606E SECTABLE FILE is too large - CP
virtual buffer will be > 64K BYTES.
Explanation: SECTABLE FILE was too large to fit into
the 64K buffer prepared for it by CP.
System Action: The application terminated.
User Response: Edit SECTABLE FILE to make it
smaller than 64K bytes long.
HCP8607E Record record number causes CP
virtual buffer to overflow 64K bytes.
Explanation: SECTABLE FILE was too large to fit into
the 64K buffer prepared for it by CP. The record
mentioned in this message is the one that caused the
file to exceed the 64K limit.
System Action: The application terminated.
User Response: Edit SECTABLE FILE to make it
smaller than 64K bytes long.
HCP8608E The following represent invalid
SECTABLE FILE records:
Explanation: The records listed after this message
violate the formatting requirements for SECTABLE FILE.
System Action: The SECTABLE application program
terminated.
User Response: Edit the records in SECTABLE FILE
so that they conform to the following format:
Table 5. Record format for SECTABLE FILE.
Column Content
1 – 8 SECLABEL character string
9 Required blank space
10 – 141 Identification label (1 to 132 characters
long)
HCP8609E A total of n records were found to be
invalid.
Explanation: The records listed before this message
violate the formatting requirements for SECTABLE FILE.
System Action: The SECTABLE application program
terminated. If you specified the STORE option, then the
number of records mentioned in the message is the
total number of format violations in SECTABLE FILE. If
you did not specify STORE, then the number of records
mentioned indicates the number of format violations
before the file began to go over the 64 KB limit.
User Response: See message HCP8608E.