AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

Chapter 11 – GPRS Commands This parameter specifies the relative importance for handling of all SDUs belonging to the UMTS bearer compared to the SDUs of the other bearers. 0 subscribed. Default 1 2 3 Packet Data Protocol Type “IP“ Notes: • If parameters are not defined, the parameter default values depend on the HLR-stored subscribed default values. • Definitions of parameters can be found in 3GPP TS 23.107 11.9 AT+CGPADDR Show PDP Adress Description: The test command returns a list of defined s. The write command returns a list of PDP addresses for the specified context identifiers. If no is specified, the addresses for all defined contexts are returned. Test Command Syntax: AT+CGPADDR= Response: [+CGPADDR: (list of defined s)] OK Write Command Syntax: AT+CGPADDR=[[,]] Response: [+CGPADDR: , ] [+CGPADDR: , ] OK ERROR +CME ERROR Parameter Descriptions: A numeric parameter which specifies a particular PDP context definition (see AT+CGDCONT command). A string that identifies the MT in the address space applicable to the PDP. The address may be static or dynamic. Note: If no is specified, the write command will return a list of all defined contexts. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 154
11.10 AT+CGQMIN Quality of Service Profile (Minimum Acceptable) Chapter 11 – GPRS Commands Description: The test command returns values supported as a compound value. If the MT supports several PDP types, the parameter value ranges for each PDP type are returned on a separate line. The read command returns the current settings for each defined context. This command allows the TE to specify a minimum acceptable profile which is checked by the MT against the negotiated profile returned in the Activate PDP Context Accept message. The set command specifies a profile for the context identified by the (local) context identification parameter, . A special form of the set command, AT+CGQMIN= causes the minimum acceptable profile for context number to become undefined. In this case no check is made against the negotiated profile. AT&F and ATZ will undefine the minimum QoS profiles of every context which is not active or not online. Test Command Syntax: AT+CGQMIN= Response: Read Command Syntax: AT+CGQMIN Response: Write Command: Response: +CGQMIN: , (list of supported s), (list of supported s), (list of supported s), (list of supported s), (list of supported s) OK ERROR +CME ERROR [+CGQMIN : , , , , , ] [+CGQMIN : ...] OK ERROR +CME ERROR AT+CGQMIN=[[, [, [, [, [, ]]]]]] OK ERROR +CME ERROR Parameter Descriptions: Parameter specifies a particular PDP context definition. The parameter is local to the TE-MT interface and is used in other PDP context-related commands. 1...2 Precedence class 0 Network subscribed value. Default. 1 High Priority. Service commitments shall be maintained ahead of precedence classes 2 and 3 2 Normal priority. Service commitments shall be maintained ahead of precedence class 3 3 Low priority. Service commitments shall be maintained (num) Delay class The delay parameter defines the end-to-end transfer delay incurred in the transmission of SDUs through the GPRS network(s). 0 Network subscribed value. Default. 1..4 SDU size: 128 octets and SDU size: 1024 octets: Delay Class Mean Transfer Delay 95 percentile 1 (Predictive)
Page 1 and 2:
Wireless EDGE Modems MultiModem ®
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8:
Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10:
Chapter 1 - Introduction Chapter 1.
Page 11 and 12:
1.5 Supported Character Sets Chapte
Page 13 and 14:
Chapter 1 - Introduction Figure 1.2
Page 15 and 16:
Chapter 1 - Introduction 1.5.2.2 Im
Page 17 and 18:
Chapter 1 - Introduction For most o
Page 19 and 20:
Chapter 2 - Configuration Commands
Page 21 and 22:
2.5 ATV Set Result Code Format Mode
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
3.2 AT+CIND Indicator control Descr
Page 39 and 40:
Chapter 3 - Status Control Commands
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Chapter 4 - Serial Interface Contro
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
5.2 AT+CPIN2 PIN2 Authentication Ch
Page 63 and 64:
Page 65 and 66:
5.4 AT+CLCK Facility Lock Chapter 4
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Chapter 6 - Identification Commands
Page 73 and 74:
Chapter 6 - Identification Commands
Page 75 and 76:
7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78:
Chapter 7 - Call-Related Commands 7
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Chapter 7 - Call-Related Commands
Page 89 and 90:
Chapter 7 - Call-Related Commands E
Page 91 and 92:
Page 93 and 94:
Chapter 8 - Network Service Command
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104: Chapter 8 - Network Service Command
Page 105 and 106: Chapter 8 - Network Service Command
Page 107 and 108: Chapter 9 - Supplementary Service C
Page 117 and 118: 9.10 AT+CLIR Calling Line Identific
Page 121 and 122: Chapter 10 - Internet Service Comma
Page 123 and 124: Write Command Syntax: Response: AT^
Page 143 and 144: Chapter 11 - GPRS Commands Chapter
Page 145 and 146: 11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148: Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150: Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152: Chapter 11 - GPRS Commands This pa
Page 153: Chapter 11 - GPRS Commands This pa
Page 157 and 158: Chapter 11 - GPRS Commands 11.11 AT
Page 167 and 168: Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170: Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172: Chapter 13 - Short Message Service
Page 193 and 194: Chapter 14 - SIM-Related Commands C
Page 195 and 196: Chapter 14 - SIM-Related Commands 1
Page 197 and 198: Chapter 14 - SIM-Related Commands 1
Page 199 and 200: Chapter 15 - SIM Application Toolki
Page 201 and 202: Chapter 17 - Audio Commands Chapter
Page 203 and 204: Chapter 17 - Audio Commands Please
Page 205 and 206:
Chapter 17 - Audio Commands 16.5 AT
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Chapter 17 - Audio Commands 16.10 A
Page 213 and 214:
Chapter 17 - Audio Commands Chapter
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Chapter 18 - Hardware-Related Comma
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Chapter 19 - Miscellaneous Commands
Page 235 and 236:
Chapter 20 - Summary Tables 20.2 St
Page 237 and 238:
Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240:
Chapter 20 - Summary Tables Interne
Page 241 and 242:
Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244:
Chapter 20 - Summary Tables Interne
Page 245 and 246:
Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248:
Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250:
Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252:
Chapter 20 - Summary Tables Command
Page 253:
Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?