AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

Chapter 13 – Short Message Service (SMS) Commands 13.8 AT+CMGW Write Short Messages to Memory Description: The execute and write commands transmit a short message (either SMS-DELIVER or SMS-SUBMIT) from TE to memory storage . Memory location of the stored message is returned. Message status will be set to ‘stored unsent’ unless otherwise given in parameter . After invoking the execute or write command wait for the prompt “>” and then start to write the message. To save the message simply enter . After the prompt a timer will be started to observe the input. To abort writing use . Abortion is acknowledged with “OK”, though the message will not be saved. Test Command Syntax: AT+CMGW= Response: OK Exec Command Syntax: If text mode (see AT+CMGF=1): AT+CMGW Response: Text can be entered. / +CMGW: OK If writing fails ERROR +CMS ERROR Write Command Syntax: If text mode (see AT+CMGF=1): AT+CMGW=/[, [/][, ]] Text can be entered. / Response: +CMGW: OK If writing fails see notes below. Write Command Syntax: If PDU mode (see AT+CMGF=0): AT+CMGW=[, ] PDU can be entered. / Response: +CMGW: OK If writing fails see notes below. Notes: • If writing fails, for example, if a message is too long, the result code depends on the current setting of the AT^SM20 command: If the AT^SM20 =1 (factory default) any failure to send a message is responded with “OK”. Users should be aware, that despite the “OK” response, the message will not be written to the selected SMS storage. If the AT^SM20 equals 0 any failure to write a message is responded with “ERROR”. If writing fails due to timeout, then AT^SM20 =1 causes “+CMS ERROR: Unknown error” to be returned; AT^SM20 =0 causes “+CMS ERROR: timer expired” to be returned. • Note that some providers do not recognize an @ symbol used in a short message. A widely used alternative is typing “*” as defined in GSM 03.40 (GPP TS 23.40). • For baudrates lower than 19200 it is recommended to use the line termination character only (refer to ATS3= , default ) before entering the text or PDU. Use of the line termination character followed by the response formating character (see ATS4= , default ) may cause problems. • SMS-COMMANDs and SMS-STATUS-REPORTs cannot be stored in text mode. • All characters entered behind the “>” prompt will be recognized as GSM characters. For example, “Backspace” (ASCII character 8) does not delete a character, but will be inserted into the short message as an additional physical character. As a result, the character you wanted to delete still appears in the text, plus the GSM code equivalent of the Backspace key. • In text mode, the maximum length of a short message depends on the used coding scheme: It is 160 characters if the 7 bit GSM coding scheme is used, and 140 characters according to the 8 bit GSM coding scheme. • The length of 8-bit data coded short messages has to be greater than 0. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 178
Chapter 13 – Short Message Service (SMS) Commands 13.9 AT+CMSS Send Short Messages from Storage Description: The write command sends message with location value from message storage to the network (SMS-SUBMIT or SMS-COMMAND). If new recipient address is given for SMS-SUBMIT, it shall be used instead of the one stored with the message. Reference value is returned to the TE on successful message delivery. Value can be used to identify message upon unsolicited delivery status report result code. If the optional parameter is given, the old status of the short message at remains unchanged (see ). Test Command Syntax: AT+CMSS= Response: OK Write Command Syntax: If text mode (AT+CMGF=1): AT+CMSS=[, [, ]] Response: +CMSS: [, ] OK If sending fails ERROR +CMS ERROR Write Command Syntax: If PDU mode (AT+CMGF=0): AT+CMSS=[, [, ]] Response: +CMSS: [, ] OK If sending fails ERROR +CMS ERROR 13.10 AT+CNMA New SMS Message Acknowledge to ME/TE Phase 2+ Description: The write / execute command confirms successful receipt of a new message (SMS- DELIVER or SMS-STATUSREPORT) routed directly to the TE. TA shall not send another +CMT or +CDS result code to TE until previous one is acknowledged. If ME does not receive acknowledgment within required time (network time-out), ME sends RP-ERROR to the network. TA shall automatically disable routing to TE by setting both and values of AT+CNMI to zero. Test Command Syntax: AT+CNMA= Response: +CNMA: (list of supported s) OK Exec Command Syntax: AT+CNMA Response: OK ERROR +CMS ERROR Write Command Syntax: AT+CNMA= Response: OK ERROR +CMS ERROR Parameter Description: 0 Parameter is only required for PDU mode. Command operates similarly as in text mode. Notes: • The execute / write command shall only be used when AT+CSMS parameter equals 1 (= phase 2+). • Both the execute and the write command can be used no matter whether text mode or PDU mode is activated. • If multiplex mode is activated (AT+CMUX=0) the AT+CNMI parameter will be set to zero on all channels, if one channel fails to acknowledge an incoming message within the required time. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 179
Page 1 and 2:
Wireless EDGE Modems MultiModem ®
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8:
Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10:
Chapter 1 - Introduction Chapter 1.
Page 11 and 12:
1.5 Supported Character Sets Chapte
Page 13 and 14:
Chapter 1 - Introduction Figure 1.2
Page 15 and 16:
Chapter 1 - Introduction 1.5.2.2 Im
Page 17 and 18:
Chapter 1 - Introduction For most o
Page 19 and 20:
Chapter 2 - Configuration Commands
Page 21 and 22:
2.5 ATV Set Result Code Format Mode
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
3.2 AT+CIND Indicator control Descr
Page 39 and 40:
Chapter 3 - Status Control Commands
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Chapter 4 - Serial Interface Contro
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
5.2 AT+CPIN2 PIN2 Authentication Ch
Page 63 and 64:
Page 65 and 66:
5.4 AT+CLCK Facility Lock Chapter 4
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Chapter 6 - Identification Commands
Page 73 and 74:
Chapter 6 - Identification Commands
Page 75 and 76:
7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78:
Chapter 7 - Call-Related Commands 7
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Chapter 7 - Call-Related Commands
Page 89 and 90:
Chapter 7 - Call-Related Commands E
Page 91 and 92:
Page 93 and 94:
Chapter 8 - Network Service Command
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Chapter 9 - Supplementary Service C
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
9.10 AT+CLIR Calling Line Identific
Page 119 and 120:
Page 121 and 122:
Chapter 10 - Internet Service Comma
Page 123 and 124:
Write Command Syntax: Response: AT^
Page 125 and 126:
Chapter 10 - Internet Service Comma
Page 127 and 128: Chapter 10 - Internet Service Comma
Page 143 and 144: Chapter 11 - GPRS Commands Chapter
Page 145 and 146: 11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148: Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150: Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152: Chapter 11 - GPRS Commands This pa
Page 153 and 154: Chapter 11 - GPRS Commands This pa
Page 155 and 156: 11.10 AT+CGQMIN Quality of Service
Page 157 and 158: Chapter 11 - GPRS Commands 11.11 AT
Page 167 and 168: Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170: Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172: Chapter 13 - Short Message Service
Page 177: Chapter 13 - Short Message Service
Page 193 and 194: Chapter 14 - SIM-Related Commands C
Page 195 and 196: Chapter 14 - SIM-Related Commands 1
Page 197 and 198: Chapter 14 - SIM-Related Commands 1
Page 199 and 200: Chapter 15 - SIM Application Toolki
Page 201 and 202: Chapter 17 - Audio Commands Chapter
Page 203 and 204: Chapter 17 - Audio Commands Please
Page 205 and 206: Chapter 17 - Audio Commands 16.5 AT
Page 211 and 212: Chapter 17 - Audio Commands 16.10 A
Page 213 and 214: Chapter 17 - Audio Commands Chapter
Page 225 and 226: Chapter 18 - Hardware-Related Comma
Page 227 and 228: Chapter 18 - Hardware-Related Comma
Page 229 and 230:
Chapter 18 - Hardware-Related Comma
Page 231 and 232:
Chapter 18 - Hardware-Related Comma
Page 233 and 234:
Chapter 19 - Miscellaneous Commands
Page 235 and 236:
Chapter 20 - Summary Tables 20.2 St
Page 237 and 238:
Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240:
Chapter 20 - Summary Tables Interne
Page 241 and 242:
Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244:
Chapter 20 - Summary Tables Interne
Page 245 and 246:
Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248:
Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250:
Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252:
Chapter 20 - Summary Tables Command
Page 253:
Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?