AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

17.19 AT^SRTC Ring Tone Configuration Description: Test Command: Response: Read Command: Response: Chapter 17 – Audio Commands The AT^SRTC read command returns the current and current . It can be used while test playback is off or on. In the latter case, see execute command for details. The AT^SRTC execute command is intended for testing. It starts to play a melody from the audio output currently selected with AT^SNFS. To deactivate test playback use AT^SRTC again. During test playback, you can enter the write command to select another melody and adjust the volume. Also, you can enter the read command to check the type and volume of the current ring tone and to view the status of playback (on / off). The test ringing signal cannot be activated when an MTC is ringing (ERROR). Selecting =0 during the test, immediately stops playback. After this, ring tones will be muted until you change using the write command. The AT^SRTC write command chooses the type and volume of ring tones. The settings can be changed no matter whether or not the ME is ringing. The selected type and volume are saved in the non-volatile Flash memory and, thus, are retained after Power Down. An exception is =0, that can be entered to quickly mute the tone or melody currently played to indicate an event. =0 only stops immediately the audible ring tone, but does not terminate the URC that indicates the event (for example RING). No permanent settings are changed or saved. AT^SRTC= ^SRTC:(list of supported) s, (list of supported) s OK AT^SRTC ^SRTC: , , OK AT^SRTC OK Exec Command: Response: Write Command: AT^SRTC=[][, ] Response: ^SRTC: , OK ERROR Parameter Description: Type of ring tone. You have a choice of 7 different ring tones and melodies. All will be played from the audio output selected with the AT^SNFS command. =0 is only intended for muting. 0 Mutes the currently played tone immediately. 1 Sequence 1 2 Sequence 2 3 Sequence 3 4 Sequence 4 5 Sequence 5 6 Sequence 6 7 Sequence 7 Volume of ring tone, varies from low to high 0 Mute 1 Very low 2 Identical with 1 3 Low 4 Identical with 3 5 Middle 6 Identical with 5 7 High Status of test ringing. Indicates whether or not a melody is currently being played back for testing 0 Switched off 1 Switched on Notes: • Before first using ring tones note that the following settings apply: We have chosen to let you decide your own preferences when you start using ring tones. Therefore, factory setting is AT^SRTC=3,0,0 (ring tones are muted). To activate ring tones for the very first time, first enter the write command and simply change the volume. After applying a firmware update the volume and type selected before the firmware update will be preserved. • The test ringing signal cannot be activated while an MTC is ringing (ERROR). • If an MTC arrives during test playback, test ringing will be deactivated and “normal” ringing reactivated (RING). Likewise, an MOC will also stop test ringing. • If no optional parameter is entered, the old value will be kept. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 224
Chapter 18 – Hardware-Related Commands Chapter 18. Hardware-Related Commands The AT Commands described in this chapter are related to the Multi-Tech wireless modem’s hardware interface. 18.1 AT+CCLK Real Time Clock Test Command Syntax: AT+CCLK= Response: OK Read Command Syntax: AT+CCLK Response: +CCLK: OK Write Command Synatx: AT+CCLK= Response: +CME ERROR: ERROR OK Parameter Description: Format is “yy/mm/dd,hh:mm:ss”, where the characters indicate the two last digits of the year, followed by month, day, hour, minutes, seconds; for example 6 th of July 2005, 22:10:00 hours equals to “05/07/06,22:10:00” Factory default is “02/01/01,00:00:00” Notes: • is retained if the device enters the Power Down mode via AT^SMSO. • will be reset to its factory default if power is totally disconnected. In this case, the clock starts with = “02/01/01,00:00:00” upon next power-up. • Each time the Multi-Tech wireless modem is restarted it takes 2s to re-initialize the RTC and to update the current time. Therefore, it is recommended to wait 2s before using the commands AT+CCLK and AT+CALA (for example 2s after ^SYSSTART has been output). Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 225
Page 1 and 2:
Wireless EDGE Modems MultiModem ®
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8:
Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10:
Chapter 1 - Introduction Chapter 1.
Page 11 and 12:
1.5 Supported Character Sets Chapte
Page 13 and 14:
Chapter 1 - Introduction Figure 1.2
Page 15 and 16:
Chapter 1 - Introduction 1.5.2.2 Im
Page 17 and 18:
Chapter 1 - Introduction For most o
Page 19 and 20:
Chapter 2 - Configuration Commands
Page 21 and 22:
2.5 ATV Set Result Code Format Mode
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
3.2 AT+CIND Indicator control Descr
Page 39 and 40:
Chapter 3 - Status Control Commands
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Chapter 4 - Serial Interface Contro
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
5.2 AT+CPIN2 PIN2 Authentication Ch
Page 63 and 64:
Page 65 and 66:
5.4 AT+CLCK Facility Lock Chapter 4
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Chapter 6 - Identification Commands
Page 73 and 74:
Chapter 6 - Identification Commands
Page 75 and 76:
7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78:
Chapter 7 - Call-Related Commands 7
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Chapter 7 - Call-Related Commands
Page 89 and 90:
Chapter 7 - Call-Related Commands E
Page 91 and 92:
Page 93 and 94:
Chapter 8 - Network Service Command
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Chapter 9 - Supplementary Service C
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
9.10 AT+CLIR Calling Line Identific
Page 119 and 120:
Page 121 and 122:
Chapter 10 - Internet Service Comma
Page 123 and 124:
Write Command Syntax: Response: AT^
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Chapter 11 - GPRS Commands Chapter
Page 145 and 146:
11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148:
Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150:
Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152:
Chapter 11 - GPRS Commands This pa
Page 153 and 154:
Chapter 11 - GPRS Commands This pa
Page 155 and 156:
11.10 AT+CGQMIN Quality of Service
Page 157 and 158:
Chapter 11 - GPRS Commands 11.11 AT
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170:
Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172:
Chapter 13 - Short Message Service
Page 173 and 174: Chapter 13 - Short Message Service
Page 193 and 194: Chapter 14 - SIM-Related Commands C
Page 195 and 196: Chapter 14 - SIM-Related Commands 1
Page 197 and 198: Chapter 14 - SIM-Related Commands 1
Page 199 and 200: Chapter 15 - SIM Application Toolki
Page 201 and 202: Chapter 17 - Audio Commands Chapter
Page 203 and 204: Chapter 17 - Audio Commands Please
Page 205 and 206: Chapter 17 - Audio Commands 16.5 AT
Page 211 and 212: Chapter 17 - Audio Commands 16.10 A
Page 213 and 214: Chapter 17 - Audio Commands Chapter
Page 223: Chapter 17 - Audio Commands 17.17 A
Page 227 and 228: Chapter 18 - Hardware-Related Comma
Page 233 and 234: Chapter 19 - Miscellaneous Commands
Page 235 and 236: Chapter 20 - Summary Tables 20.2 St
Page 237 and 238: Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240: Chapter 20 - Summary Tables Interne
Page 241 and 242: Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244: Chapter 20 - Summary Tables Interne
Page 245 and 246: Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248: Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250: Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252: Chapter 20 - Summary Tables Command
Page 253: Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?