AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

Chapter 4 – Serial Interface Control Commands Example 4: To specify a new “PS” lock password To specify a new “PS” lock password, after the old password was disabled (e.g., after three failed attempts to change the “PS” password): use the master phone code. CAUTION: THIS TEST SHOULD BE PERFORMED ONLY IF THE CORRECT MASTER PHONE CODE FOR THE INDIVIDUAL ME USED IS DEFINITELY AVAILABLE! Otherwise, the module used will be rendered useless until the correct master phone code is entered: AT+CPWD=”PS”,”12345678”,”1111” where 12345678 is the Master Phone Code and 1111 is the new password. You may also use to restore the former disabled password. OK Alternatively, without giving a new password: AT+CPWD=”PS”,”12345678” (where 12345678 is the Master Phone Code). Deactivates the present phone lock. OK 5.7 AT^SPWD Change Password Description: The AT^SPWD command is, in every respect, identical with AT+CPWD, except that the command syntax and response prefix is “^SPWD” instead of “+CPWD”. For further description please refer to AT+CPWD. See also AT commands AT+CLCK and AT^SLCK for more information on the various lock features. The write AT^SPWD command allows to define a new password for a password protected lock function. Each password is a string of digits, the length of which varies with the associated . The test command returns a list of pairs which represent the available facilities and the maximum length of the associated password. Use this command when you want to change the passwords defined for the “facility lock” functions available from AT+CLCK. Specifically the command can be used to • change PIN1 or PIN2, • change the password supplied from your provider for the “call barring” supplementary service, • set individual phone security passwords, • enter the unblocking key (Master Phone Code) to restore a disabled “PS” password. See also AT Commands AT+CLCK and AT^SLCK for more information on the vaious lock features. Test Command Syntax: AT^SPWD= Response: ^SPWD : list of supported (, ) OK Write Command Syntax: AT^SPWD=[,][, ] Response: New password has been registered for the facility lock function: OK Note: If parameter was not correct: +CME ERROR 16 (+CME ERROR: incorrect password) If the password for the selected has been invalidated due to too many failed attempts: +CME ERROR ... When trying to set a “CM” password even though another type of factory set SIM lock is already active: +CME ERROR: Operation not supported. If error is related to ME functionality: +CME ERROR When changing the PIN2 (=”P2”), it is recommended to check the new state of PIN2 using the AT+CPIN2 command. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 70
Chapter 6 – Identification Commands Chapter 6. Identification Commands The AT Commands described in this chapter allow the external application to obtain various identification information related to the Multi-Tech wireless modem and linked entities. 6.1 ATI Display Product Identification Information Description: Exec Command Syntax: ATI Response: The ATI execute command delivers a product information text. The ‘Revision’ information consists of the following parts: Version xx and variant yy of software release. SIEMENS MC75 REVISION xx.yy OK Exec Command Syntax: ATI[] Response: OK Parameter Description: Values are not support and only return OK. 6.2 AT+CGMI Request Manufacturer Identification Description: AT+CGMI returns a manufacturer identification text. See also: AT+GMI. Test Command Syntax: AT+CGMI= Response: OK Exec Command Syntax: AT+CGMI Response: SIEMENS OK 6.3 AT+GMI Request Manufacturer Identification Description: AT+GMI returns a manufacturer identification text. See also: AT+CGMI. Test Command Syntax: AT+GMI= Response: OK Exec Command Syntax: AT+GMI Response: SIEMENS OK 6.4 AT+CGMM Request Model Identification Description: AT+CGMM returns a product model identification text. Command is identical with AT+GMM. Test Command Syntax: AT+CGMM= Response: OK Exec Command Syntax: AT+CGMM Response: MC75 OK 6.5 AT+GMM Request Model Identification Description: AT+GMM returns a product model identification text. Command is identical with AT+CGMM. Test Command Syntax: AT+GMM= Response: OK Exec Command Syntax: AT+GMM Response: MC75 OK Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 71
Page 1 and 2:
Wireless EDGE Modems MultiModem ®
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8:
Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10:
Chapter 1 - Introduction Chapter 1.
Page 11 and 12:
1.5 Supported Character Sets Chapte
Page 13 and 14:
Chapter 1 - Introduction Figure 1.2
Page 15 and 16:
Chapter 1 - Introduction 1.5.2.2 Im
Page 17 and 18:
Chapter 1 - Introduction For most o
Page 19 and 20: Chapter 2 - Configuration Commands
Page 21 and 22: 2.5 ATV Set Result Code Format Mode
Page 37 and 38: 3.2 AT+CIND Indicator control Descr
Page 39 and 40: Chapter 3 - Status Control Commands
Page 51 and 52: Chapter 4 - Serial Interface Contro
Page 61 and 62: 5.2 AT+CPIN2 PIN2 Authentication Ch
Page 65 and 66: 5.4 AT+CLCK Facility Lock Chapter 4
Page 69: Chapter 4 - Serial Interface Contro
Page 73 and 74: Chapter 6 - Identification Commands
Page 75 and 76: 7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78: Chapter 7 - Call-Related Commands 7
Page 87 and 88: Chapter 7 - Call-Related Commands
Page 89 and 90: Chapter 7 - Call-Related Commands E
Page 93 and 94: Chapter 8 - Network Service Command
Page 107 and 108: Chapter 9 - Supplementary Service C
Page 117 and 118: 9.10 AT+CLIR Calling Line Identific
Page 121 and 122:
Chapter 10 - Internet Service Comma
Page 123 and 124:
Write Command Syntax: Response: AT^
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Chapter 11 - GPRS Commands Chapter
Page 145 and 146:
11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148:
Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150:
Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152:
Chapter 11 - GPRS Commands This pa
Page 153 and 154:
Chapter 11 - GPRS Commands This pa
Page 155 and 156:
11.10 AT+CGQMIN Quality of Service
Page 157 and 158:
Chapter 11 - GPRS Commands 11.11 AT
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170:
Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172:
Chapter 13 - Short Message Service
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Chapter 14 - SIM-Related Commands C
Page 195 and 196:
Chapter 14 - SIM-Related Commands 1
Page 197 and 198:
Chapter 14 - SIM-Related Commands 1
Page 199 and 200:
Chapter 15 - SIM Application Toolki
Page 201 and 202:
Chapter 17 - Audio Commands Chapter
Page 203 and 204:
Chapter 17 - Audio Commands Please
Page 205 and 206:
Chapter 17 - Audio Commands 16.5 AT
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Chapter 17 - Audio Commands 16.10 A
Page 213 and 214:
Chapter 17 - Audio Commands Chapter
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Chapter 18 - Hardware-Related Comma
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Chapter 19 - Miscellaneous Commands
Page 235 and 236:
Chapter 20 - Summary Tables 20.2 St
Page 237 and 238:
Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240:
Chapter 20 - Summary Tables Interne
Page 241 and 242:
Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244:
Chapter 20 - Summary Tables Interne
Page 245 and 246:
Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248:
Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250:
Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252:
Chapter 20 - Summary Tables Command
Page 253:
Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?