AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

Chapter 3 – Status Control Commands 3.7 AT+WS46 Select Wireless Network Test Command Syntax: AT+WS46= Test Response: +WS46: (list of supporteds) OK Read Command Syntax: AT+WS46 Read Response: OK Write Command Syntax: AT+WS46=[] Write Response: OK ERROR +CME ERROR Parameter Description 12 GSM digital cellular Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 50
Chapter 4 – Serial Interface Control Commands Chapter 4. Serial Interface Control Commands The AT Commands described in this chapter allow the external application to determine various settings related to the Multi-Tech wireless modem’s serial interface. 4.1 AT\Q Flow Control Exec Command Syntax: AT\Q[] Response: OK If RTS/CTS flow control is not supported by interface and is 2 or 3: ERROR Parameter Description: 0 Disable flow control. Default. 1 XON/XOFF software flow control 2 Only CTS by DCE (TA) 3 RTS/CTS hardware flow control Recommended for the following procedures: incoming or outgoing data calls, fax calls, MUX mode. Often, the initialization routine of Fax programs includes enabling RTS/CTS handshake, eliminating the need to issue AT\Q3 once again. Notes: • When using XON/XOFF flow control (AT\Q1) in online mode, +++ should not be used while the data transmission is paused with XOFF. Before entering the command mode with +++ the paused transmission should be resumed using the XON character. • Flow Control can be set by also using AT+IFC. 4.2 AT&C Set Circuit Data Carrier Detect (DCD) Function Mode Description: Exec Command Syntax: AT&C[value] Response: OK The AT&C command determines how the state of circuit 109 (DCD) relates to the detection of received line signal from the distant end. Parameter Description: 0 DCD line is always ON. Default. 1 DCD line is ON in the presence of data carrier only. 4.3 AT&D Set Circuit Data Terminal Ready (DTR) Function Mode Description: The AT&D determines how the TA responds when circuit 108/2 (DTR) is changed from ON to OFF during data mode. Exec Command Syntax: AT&D[] Response: OK Parameter Description: 0 TA ignores status of DTR. Default. 1 ON->OFF on DTR: Change to command mode while retaining the connected call. 2 ON->OFF on DTR: Disconnect data call, change to command mode. During state DTR = OFF auto-answer is off. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 51
Page 1 and 2: Wireless EDGE Modems MultiModem ®
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8: Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10: Chapter 1 - Introduction Chapter 1.
Page 11 and 12: 1.5 Supported Character Sets Chapte
Page 13 and 14: Chapter 1 - Introduction Figure 1.2
Page 15 and 16: Chapter 1 - Introduction 1.5.2.2 Im
Page 17 and 18: Chapter 1 - Introduction For most o
Page 19 and 20: Chapter 2 - Configuration Commands
Page 21 and 22: 2.5 ATV Set Result Code Format Mode
Page 37 and 38: 3.2 AT+CIND Indicator control Descr
Page 39 and 40: Chapter 3 - Status Control Commands
Page 49: Chapter 3 - Status Control Commands
Page 53 and 54: Chapter 4 - Serial Interface Contro
Page 61 and 62: 5.2 AT+CPIN2 PIN2 Authentication Ch
Page 65 and 66: 5.4 AT+CLCK Facility Lock Chapter 4
Page 71 and 72: Chapter 6 - Identification Commands
Page 73 and 74: Chapter 6 - Identification Commands
Page 75 and 76: 7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78: Chapter 7 - Call-Related Commands 7
Page 87 and 88: Chapter 7 - Call-Related Commands
Page 89 and 90: Chapter 7 - Call-Related Commands E
Page 93 and 94: Chapter 8 - Network Service Command
Page 101 and 102:
Chapter 8 - Network Service Command
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Chapter 9 - Supplementary Service C
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
9.10 AT+CLIR Calling Line Identific
Page 119 and 120:
Page 121 and 122:
Chapter 10 - Internet Service Comma
Page 123 and 124:
Write Command Syntax: Response: AT^
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Chapter 11 - GPRS Commands Chapter
Page 145 and 146:
11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148:
Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150:
Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152:
Chapter 11 - GPRS Commands This pa
Page 153 and 154:
Chapter 11 - GPRS Commands This pa
Page 155 and 156:
11.10 AT+CGQMIN Quality of Service
Page 157 and 158:
Chapter 11 - GPRS Commands 11.11 AT
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170:
Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172:
Chapter 13 - Short Message Service
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Chapter 14 - SIM-Related Commands C
Page 195 and 196:
Chapter 14 - SIM-Related Commands 1
Page 197 and 198:
Chapter 14 - SIM-Related Commands 1
Page 199 and 200:
Chapter 15 - SIM Application Toolki
Page 201 and 202:
Chapter 17 - Audio Commands Chapter
Page 203 and 204:
Chapter 17 - Audio Commands Please
Page 205 and 206:
Chapter 17 - Audio Commands 16.5 AT
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Chapter 17 - Audio Commands 16.10 A
Page 213 and 214:
Chapter 17 - Audio Commands Chapter
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Chapter 18 - Hardware-Related Comma
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Chapter 19 - Miscellaneous Commands
Page 235 and 236:
Chapter 20 - Summary Tables 20.2 St
Page 237 and 238:
Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240:
Chapter 20 - Summary Tables Interne
Page 241 and 242:
Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244:
Chapter 20 - Summary Tables Interne
Page 245 and 246:
Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248:
Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250:
Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252:
Chapter 20 - Summary Tables Command
Page 253:
Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?