AT Command Reference Guide for EDGE Wireless ... - wless.ru
AT Command Reference Guide for EDGE Wireless ... - wless.ru
AT Command Reference Guide for EDGE Wireless ... - wless.ru
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Chapter 2 – Configuration <strong>Command</strong>s<br />
2.2.1 <strong>AT</strong>&V Responses<br />
The following table shows different kinds of responses depending on whether or not the PIN is entered.<br />
Table 2.1: Current configuration on ASC0 channel 1 (example)<br />
PIN authentication done<br />
ACTIVE PROFILE:<br />
E1 Q0 V1 X4 &C1 &D2 &S0 \Q0 \V1<br />
S0:000 S3:013 S4:010 S5:008 S6:000 S7:060 S8:000<br />
S10:002 S18:000<br />
+CBST: 7,0,1<br />
+CRLP: 61,61,78,6<br />
+CR: 0<br />
+FCLASS: 0<br />
+CRC: 0<br />
+CMGF: 0<br />
+CSDH: 0<br />
+CNMI: 0,0,0,0,1<br />
+IFC:3<br />
+IFC:0,0<br />
+ILRR: 0<br />
+IPR: 115200<br />
+CMEE: 2<br />
^SMGO: 0,0<br />
+CSMS: 0,1,1,1<br />
^SACM: 0,”000000”,”000000”<br />
^SLCC: 0<br />
^SCKS: 0,1<br />
^SSET:0<br />
+CREG: 0,1<br />
+CLIP: 0,2<br />
+CAOC: 0<br />
+COPS: 0,0,”operator”<br />
+CGSMS: 3<br />
OK<br />
Note: Table 2.2 has been intentionally omitted.<br />
No PIN authentication<br />
ACTIVE PROFILE:<br />
E1 Q0 V1 X4 &C1 &D2 &S0 \Q0 \V1<br />
S0:000 S3:013 S4:010 S5:008 S6:000 S7:060 S8:000<br />
S10:002 S18:000<br />
+CBST: 7,0,1<br />
+CRLP: 61,61,78,6<br />
+CR: 0<br />
+FCLASS: 0<br />
+IFC:3<br />
+IFC:0,0<br />
+ILRR: 0<br />
+IPR: 115200<br />
+CMEE: 2<br />
^SCKS: 0,1<br />
^SSET:0<br />
OK<br />
2.3 <strong>AT</strong>&W Stores Current Configuration<br />
Description:<br />
<strong>AT</strong>&W stores the currently parameters to a user-defined profile in the non-volatile<br />
memory.<br />
Exec <strong>Command</strong> Syntax: <strong>AT</strong>&W[value]<br />
Response:<br />
OK<br />
Parameter Values:<br />
<br />
0 Number of the profile<br />
Notes:<br />
• The user defined profile will be restored automatically after power-up. Use <strong>AT</strong>Z to restore user profile and <strong>AT</strong>&F<br />
to restore factory settings. Until the first use of <strong>AT</strong>&W, <strong>AT</strong>Z works as <strong>AT</strong>&F.<br />
• User defined profiles in multiplex mode:<br />
<strong>AT</strong>&W stores all global settings and the current settings of the interface on which the command is executed.<br />
• A list of parameters stored to the user profile can be found in Section 20.5, <strong>AT</strong> <strong>Command</strong> Settings storable with<br />
<strong>AT</strong>&W.<br />
2.4 <strong>AT</strong>Q Set Result Code Presentation Mode<br />
Description:<br />
Exec <strong>Command</strong> Syntax: <strong>AT</strong>Q<br />
Response:<br />
This parameter setting determines whether or not the TA transmits any result code to the<br />
TE. In<strong>for</strong>mation text transmitted in response is not affected by this setting.<br />
Store this parameter with the <strong>AT</strong>&W command.<br />
Display this parameter with the <strong>AT</strong>&V command.<br />
If = 0, then OK. Default<br />
If = 1, then (none).<br />
Parameter Values:<br />
<br />
0 DCE transmits result code. Default.<br />
1 Result codes are suppressed and not transmitted<br />
Multi-Tech Systems, Inc. <strong>AT</strong> <strong>Command</strong>s <strong>for</strong> <strong>EDGE</strong> Modems (S000371B) 20