AT Command Reference Guide for EDGE Wireless ... - wless.ru
AT Command Reference Guide for EDGE Wireless ... - wless.ru
AT Command Reference Guide for EDGE Wireless ... - wless.ru
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Chapter 11 – GPRS <strong>Command</strong>s<br />
11.19 <strong>AT</strong>D*98# Request GPRS IP Service<br />
Description: This command causes the MT to per<strong>for</strong>m whatever actions are necessary to establish<br />
communication between the TE and the external PDN.<br />
The V.250 ‘D’ (Dial) command causes the MT to enter the V.250 online data state and, with the<br />
TE, to start the layer 2 protocol.<br />
GPRS attachment and PDP context activation procedures may take place prior to or during the<br />
PDP startup if they have not already been per<strong>for</strong>med using <strong>AT</strong>+CG<strong>AT</strong>T and <strong>AT</strong>+CGACT.<br />
To confirm acceptance of the command be<strong>for</strong>e entering the V.250 online data state, command<br />
will respond with CONNECT.<br />
When the layer 2 protocol has terminated, either as a result of an orderly shut down of the PDP<br />
or an error, the MT enters V.250 command state and returns NO CARRIER (<strong>for</strong> details refer to<br />
Section 11.5.1, Automatic deactivation of PDP context during dial-up PPP).<br />
Exec <strong>Command</strong> Syntax: <strong>AT</strong>D*98[* ]#<br />
Response:<br />
CONNECT<br />
NO CARRIER<br />
Parameter Descriptions:<br />
<br />
Parameter specifies a particular PDP context definition (see <strong>AT</strong>+CGDCONT command). If no context is<br />
specified, an internal context with default properties is used (see <strong>AT</strong>+CGDCONT, <strong>AT</strong>+CGQREQ and<br />
<strong>AT</strong>+CGQMIN).<br />
1...2<br />
Notes:<br />
• If the Multi-Tech wireless modem is in dedicated mode, command returns the result code BUSY.<br />
• <strong>AT</strong>D is used as a standard V.250 <strong>AT</strong> command, too.<br />
11.20 <strong>AT</strong>H Manual Rejection of a Network Request<br />
<strong>for</strong> PDP Context Activation<br />
Description: The V.250 <strong>AT</strong>H command may be used to deactivate all PDP contexts which are active or online<br />
on the same interface. This command should not be used to deactivate PDP contexts during the<br />
implicit PDP context deactivation procedure which is started automatically after LCP termination<br />
or by dropping the DTR line (if <strong>AT</strong>&D2 is configured). For details refer to Section 11.5.1,<br />
“Automatic deactivation of PDP context during dial-up PPP”.<br />
The <strong>AT</strong>H command may also be used to reject a network request <strong>for</strong> PDP context activation<br />
announced by the unsolicited result codes “RING: GPRS” or “+CRING: GPRS”.<br />
Exec <strong>Command</strong> Syntax: <strong>AT</strong>H<br />
Response:<br />
OK<br />
Notes:<br />
• In contrast to GSM 07.07 it is possible to cancel a connection with <strong>AT</strong>H after a break. This is done <strong>for</strong><br />
compatibility reasons due to the “dial-up network” drivers of Microsoft Windows.<br />
• <strong>AT</strong>H is used as a standard V.250 <strong>AT</strong> command, too.<br />
• If <strong>AT</strong>H is used to reject a network request <strong>for</strong> PDP context activation, then other PDP contexts on the same<br />
interface which are active or online will not be deactivated.<br />
Multi-Tech Systems, Inc. <strong>AT</strong> <strong>Command</strong>s <strong>for</strong> <strong>EDGE</strong> Modems (S000371B) 164