AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

Chapter 4 – Serial Interface Control Commands 4.11 AT+STPB Transmit Parity Bit (for 7E1 & 7O1 Only) Description: This command is intended for use with 7E1 and 7O1 only. In addition to the 7E1 or 7O1 settings made with AT+ICF the command AT^STPB specifies whether or not to transmit the parity bit over the air. Command Descriptions: The test command returns the supported values of the parameter . The read command returns the current value of the parameter . The write command can be used to control the handling of the parity bit. If command fails, “+CME ERROR: unknown” will be returned. Test Command Syntax: AT^STPB= Response(s): ^STPB: (list of supported s) OK Read Command Syntax: AT^STPB Response(s): ^STPB: OK Write Command Syntax: AT^STPB= Response(s): OK ERROR +CME ERROR: unknown Parameter Descriptions: 0 The parity bit will not be transmitted over the air and will be replaced with 0. This mode is the default setting if 7E1 or 7O1 is activated with AT+ICF. 1 In a data connection 8 bits will be transmitted, including the parity bit; i.e., the parity bit will be properly transmitted over the air. The setting shall be used if problems are encountered when Multi-Tech wireless modem is running in the default 7E1 or 7O1 mode enabled with AT+ICF. In this case, AT^STPB=1 shall be set in addition to the 7E1 or 7O1 settings selected with AT+ICF. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 58
Chapter 4 – Serial Interface Control Commands Chapter 5. Security Commands The AT Commands described in this chapter allow the external application to determine various security related settings. 5.1 AT+CPIN PIN Authentication Description: AT+CPIN controls network authentication of the Multi-Tech wireless modem. The read command returns an alphanumeric string indicating whether or not network authentication is required. The write command allows the Multi-Tech wireless modem to store the entered password. This may be for example the SIM PIN1 to register to the GSM network, or the SIM PUK1 to replace a disabled SIM PIN1 with a new one, or the PH-SIM PIN if the client has taken precautions for preventing damage in the event of loss or theft etc. If no PIN1 request is pending (for example if PIN1 authentication has been done and the same PIN1 is entered again), the Multi-Tech wireless modem responds “+CME ERROR: operation not allowed”; no further action is required. Test Command Syntax: AT+CPIN= Response: OK Read Command Syntax: AT+CPIN Response: +CPIN: OK ERROR +CME ERROR: Write Command Syntax: AT+CPIN=[, ] Response: OK ERROR +CME ERROR: Parameter Descriptions: Password (string type), usually SIM PIN1. If the requested password was a PUK, such as SIM PUK1 or PH-FSIM PUK or another password, then must be followed by . If the requested code was a PUK: specify a new password or restore the former disabled password. See Section 5.1.1, What to do if PIN or password authentication fails for more information about when you may need to enter the PUK. SIM PIN authentication READY SIM PIN SIM PUK SIM PIN2 SIM PUK2 PIN has already been entered. No further entry needed. ME is waiting for SIM PIN1. ME is waiting for SIM PUK1 if PIN1 was disabled after three failed attempts to enter PIN1. ME is waiting for PIN2. This is only applicable when an attempt to access a PIN2 related feature was acknowledged with +CME ERROR: 17 (“SIM PIN2 required”), for example when the client attempts to edit the FD phonebook). In this case the read command AT+CPIN also prompts for SIM PIN2. Normally, the AT+CPIN2 command is intended for SIM PIN2. ME is waiting for PUK2 to unblock a disabled PIN2. As above, this is only necessary when the preceding command was acknowledged with +CME ERROR: 18 (“SIM PUK2 required”) and only if the read command AT+CPIN also prompts for SIM PUK2. Normally, the AT+CPIN2 command is intended for SIM PUK2. Phone security locks set by client or factory PH-SIM PIN PH-SIM PUK PH-FSIM PIN PH-FSIM PUK ME is waiting for phone-to-SIM card password if “PS” lock is active and the client inserts other SIM card than the one used for the lock. (“PS” lock is also referred to as phone or antitheft lock). ME is waiting for Master Phone Code, if the above “PS” lock password was incorrectly entered three times. ME is waiting for phone-to-very-first-SIM card. Necessary when “PF” lock was set. When powered up the first time, ME locks itself to the first SIM card put into the card holder. As a result, operation of the mobile is restricted to this one SIM card (unless the PH-FSIM PUK is used as described below). ME is waiting for phone-to-very-first-SIM card unblocking password to be given. Necessary when “PF” lock is active and other than first SIM card is inserted. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 59
Page 1 and 2:
Wireless EDGE Modems MultiModem ®
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8: Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10: Chapter 1 - Introduction Chapter 1.
Page 11 and 12: 1.5 Supported Character Sets Chapte
Page 13 and 14: Chapter 1 - Introduction Figure 1.2
Page 15 and 16: Chapter 1 - Introduction 1.5.2.2 Im
Page 17 and 18: Chapter 1 - Introduction For most o
Page 19 and 20: Chapter 2 - Configuration Commands
Page 21 and 22: 2.5 ATV Set Result Code Format Mode
Page 37 and 38: 3.2 AT+CIND Indicator control Descr
Page 39 and 40: Chapter 3 - Status Control Commands
Page 51 and 52: Chapter 4 - Serial Interface Contro
Page 57: Chapter 4 - Serial Interface Contro
Page 61 and 62: 5.2 AT+CPIN2 PIN2 Authentication Ch
Page 65 and 66: 5.4 AT+CLCK Facility Lock Chapter 4
Page 71 and 72: Chapter 6 - Identification Commands
Page 73 and 74: Chapter 6 - Identification Commands
Page 75 and 76: 7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78: Chapter 7 - Call-Related Commands 7
Page 87 and 88: Chapter 7 - Call-Related Commands
Page 89 and 90: Chapter 7 - Call-Related Commands E
Page 93 and 94: Chapter 8 - Network Service Command
Page 107 and 108: Chapter 9 - Supplementary Service C
Page 109 and 110:
Chapter 9 - Supplementary Service C
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
9.10 AT+CLIR Calling Line Identific
Page 119 and 120:
Page 121 and 122:
Chapter 10 - Internet Service Comma
Page 123 and 124:
Write Command Syntax: Response: AT^
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Chapter 11 - GPRS Commands Chapter
Page 145 and 146:
11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148:
Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150:
Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152:
Chapter 11 - GPRS Commands This pa
Page 153 and 154:
Chapter 11 - GPRS Commands This pa
Page 155 and 156:
11.10 AT+CGQMIN Quality of Service
Page 157 and 158:
Chapter 11 - GPRS Commands 11.11 AT
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170:
Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172:
Chapter 13 - Short Message Service
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Chapter 14 - SIM-Related Commands C
Page 195 and 196:
Chapter 14 - SIM-Related Commands 1
Page 197 and 198:
Chapter 14 - SIM-Related Commands 1
Page 199 and 200:
Chapter 15 - SIM Application Toolki
Page 201 and 202:
Chapter 17 - Audio Commands Chapter
Page 203 and 204:
Chapter 17 - Audio Commands Please
Page 205 and 206:
Chapter 17 - Audio Commands 16.5 AT
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Chapter 17 - Audio Commands 16.10 A
Page 213 and 214:
Chapter 17 - Audio Commands Chapter
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Chapter 18 - Hardware-Related Comma
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Chapter 19 - Miscellaneous Commands
Page 235 and 236:
Chapter 20 - Summary Tables 20.2 St
Page 237 and 238:
Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240:
Chapter 20 - Summary Tables Interne
Page 241 and 242:
Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244:
Chapter 20 - Summary Tables Interne
Page 245 and 246:
Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248:
Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250:
Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252:
Chapter 20 - Summary Tables Command
Page 253:
Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?