AT Command Reference Guide for EDGE Wireless ... - wless.ru

More documents

Recommendations

Info

Chapter 1 – Introduction 1.8 Common PCN Handset Specification (CPHS) The ME provides features to implement a device following the prerequisites of the Common PCN Handset Specification (CPHS) Phase 2. CPHS Feature Description/Remarks AT command Alternate Line Service Using two phone numbers with one SIM card. AT^SALS Voice Message Waiting Indication Operator (Service provider) name from SIM Network and Service Provider Lock Call Forwarding Customer Service Profile (CSP) Information numbers 1.9 Errors and Messages Indicate the receipt of a short message coded as Voice Message Waiting Indicator as defined by the CPHS Phase 2 standard. Read specific Elementary Files (6F14h, 6F18h) from SIM. Lock/Unlock an ME to specific HPLMN and service provider. Get and set diverted call status. Access specific Elementary File (6F13h) from SIM. Setting services and their menu entries depending on customer profiles. Hierarchically structured service numbers phonebook on SIM according to CPHS 4.2 (mandatory). AT^SIND, AT+CMER, indicators “vmwait1” and “vmwait2” AT+CRSM AT+CLCK, (AT+CPIN) AT+CCFC, AT+CRSM AT+CRSM AT+CRSM The command result codes “+CME ERROR: ” and “+CMS ERROR: ” indicate errors related to mobile equipment or network functionality. The format of can be either numeric or verbose and is selectable via AT+CMEE. A result error code terminates the execution of the command and prevents the execution of all remaining commands that may follow on the same command line. If so, neither “ERROR” nor “OK” result codes are returned for these commands. A 30 seconds timeout will deliver “ERROR” when the input of a command is not complete. Using the wrong command syntax may result in errors: For example, using the execute command syntax although the command has no execute format, causes “ERROR” to be returned. Likewise, using the write command syntax although the command has no write format causes “+CME ERROR: ” to be returned. See also: • Section 2.12.1, CME/CMS Error Code Overview • Section 2.5.1, Verbose and numeric result codes • Section 3.4, AT+CEER Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 18
Chapter 2 – Configuration Commands Chapter 2. Configuration Commands The AT commands described in this chapter allow the external application to determine the modem’s behavior under various conditions. 2.1 AT&F Set All Current Parameters to Manufacturer Defaults Description: AT&F sets all current parameters to the manufacturer defined profile. All defined GPRS contexts which are not activated or not online will be “undefined” (see AT+CGDCONT). Exec Command Syntax: AT&F[value] Response: OK Parameter Description: 0 Sets all TA parameters to manufacturer defaults. Notes: • List of parameters reset to manufacturer default can be found in Section 20.6, Factory Default Settings Restorable with AT&F. • In addition to the default profile, you can store an individual one with AT&W. To alternate between the two profiles enter either ATZ (loads user profile) or AT&F (restores factory profile). • Every ongoing or incoming call will be terminated. 2.2 AT&V Display Current Configuration Description: Exec Command Syntax: Response: AT&V returns the current parameter setting. The configuration varies depending on whether or not PIN authentication has been done and whether or not Multiplex mode is enabled (see AT+CMUX). AT&V[value] Active Profile (See Section 2.2.1 AT&V responses) OK Parameter Description: : 0 Profile number Notes: • The value of \Q (flow control) is also determined by the AT+IFC command. In case the value set by AT+IFC cannot be represented by a \Q equivalent, \Q255 will be displayed. The parameters of AT^SMGO can only be displayed after the SMS data from the SIM have been read successfully for the first time. Reading starts after successful SIM authentication has been performed, and may take up to 30 seconds depending on the SIM used. While the read process is in progress, an attempt to read the parameter will result in empty values. • The parameter of AT+CSDH will only be displayed in SMS text mode, see AT+CMGF. Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371B) 19
Page 1 and 2: Wireless EDGE Modems MultiModem ®
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents 8.8.1 AT^MONI Res
Page 7 and 8: Table of Contents 16.5 AT+CPBW Writ
Page 9 and 10: Chapter 1 - Introduction Chapter 1.
Page 11 and 12: 1.5 Supported Character Sets Chapte
Page 13 and 14: Chapter 1 - Introduction Figure 1.2
Page 15 and 16: Chapter 1 - Introduction 1.5.2.2 Im
Page 17: Chapter 1 - Introduction For most o
Page 21 and 22: 2.5 ATV Set Result Code Format Mode
Page 23 and 24: Chapter 2 - Configuration Commands
Page 37 and 38: 3.2 AT+CIND Indicator control Descr
Page 39 and 40: Chapter 3 - Status Control Commands
Page 51 and 52: Chapter 4 - Serial Interface Contro
Page 61 and 62: 5.2 AT+CPIN2 PIN2 Authentication Ch
Page 65 and 66: 5.4 AT+CLCK Facility Lock Chapter 4
Page 69 and 70:
Chapter 4 - Serial Interface Contro
Page 71 and 72:
Chapter 6 - Identification Commands
Page 73 and 74:
Chapter 6 - Identification Commands
Page 75 and 76:
7.2 ATA Answer a Call Chapter 7 - C
Page 77 and 78:
Chapter 7 - Call-Related Commands 7
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Chapter 7 - Call-Related Commands
Page 89 and 90:
Chapter 7 - Call-Related Commands E
Page 91 and 92:
Page 93 and 94:
Chapter 8 - Network Service Command
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Chapter 9 - Supplementary Service C
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
9.10 AT+CLIR Calling Line Identific
Page 119 and 120:
Page 121 and 122:
Chapter 10 - Internet Service Comma
Page 123 and 124:
Write Command Syntax: Response: AT^
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Chapter 11 - GPRS Commands Chapter
Page 145 and 146:
11.3 AT+CGATT GPRS Attach or Detach
Page 147 and 148:
Chapter 11 - GPRS Commands 11.5 AT+
Page 149 and 150:
Chapter 11 - GPRS Commands 11.7 AT+
Page 151 and 152:
Chapter 11 - GPRS Commands This pa
Page 153 and 154:
Chapter 11 - GPRS Commands This pa
Page 155 and 156:
11.10 AT+CGQMIN Quality of Service
Page 157 and 158:
Chapter 11 - GPRS Commands 11.11 AT
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Chapter 11 - GPRS Commands AT+CGDAT
Page 169 and 170:
Chapter 12 - FAX Commands 12.3 AT+F
Page 171 and 172:
Chapter 13 - Short Message Service
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Chapter 14 - SIM-Related Commands C
Page 195 and 196:
Chapter 14 - SIM-Related Commands 1
Page 197 and 198:
Chapter 14 - SIM-Related Commands 1
Page 199 and 200:
Chapter 15 - SIM Application Toolki
Page 201 and 202:
Chapter 17 - Audio Commands Chapter
Page 203 and 204:
Chapter 17 - Audio Commands Please
Page 205 and 206:
Chapter 17 - Audio Commands 16.5 AT
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Chapter 17 - Audio Commands 16.10 A
Page 213 and 214:
Chapter 17 - Audio Commands Chapter
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Chapter 18 - Hardware-Related Comma
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Chapter 19 - Miscellaneous Commands
Page 235 and 236:
Chapter 20 - Summary Tables 20.2 St
Page 237 and 238:
Chapter 20 - Summary Tables 20.3 AT
Page 239 and 240:
Chapter 20 - Summary Tables Interne
Page 241 and 242:
Chapter 20 - Summary Tables 20.4 Av
Page 243 and 244:
Chapter 20 - Summary Tables Interne
Page 245 and 246:
Chapter 20 - Summary Tables 20.5 AT
Page 247 and 248:
Chapter 20 - Summary Tables SIM-Rel
Page 249 and 250:
Chapter 20 - Summary Tables ^SSTN ^
Page 251 and 252:
Chapter 20 - Summary Tables Command
Page 253:
Chapter 20 - Summary Tables Command
show all

AT Command Reference Guide for EDGE Wireless ... - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?