You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Gate/Expander<br />
The Dynamics screen is only available if you have at least<br />
one of the optional Dynamics cassettes fitted.<br />
The Gate/Expander controls are accessed by pressing the DYN button,<br />
and then pressing the 1 st encoder to swap the processing screen over to<br />
the Gate/Expander view.<br />
• If the EXP button (to the left of the Channel number, press 4 th encoder)<br />
is pressed, it is operating as an Expander.<br />
• If the EXP button is not pressed (as shown left, press 4 th encoder), it is<br />
acting as a Gate.<br />
Both processes operate identically on-screen using the same parameters.<br />
The rotary controls on screen map directly to the first three encoders on<br />
the Monitor Panel.<br />
If an EQ is being used to be<br />
the Sidechain into the Gate (or<br />
Exp), it will no longer be<br />
available in the Channel (or<br />
Monitor) path.<br />
The EQ pick-off point when<br />
used in this mode will always<br />
be Pre- the Dynamics<br />
processing (but can be Post<br />
Insert if the Inserts are set<br />
Pre- Dynamics).<br />
▶ The 1 st encoder sets the Range of the Gate (or Exp) and runs from 0db<br />
to 50dB.<br />
The 2 nd encoder sets the Threshold at which the Gate (or Exp) should<br />
operate and runs from -30dB to 10dB.<br />
▶ Pressing the 2 nd encoder selects where the Sidechain Input is sourced<br />
from, either sourced from the Channel itself, the EQ output on that<br />
Channel, or from the Key Input via the 25-way D-type connector on the<br />
Dynamics cassette.<br />
• Both leds OFF means the signal is coming from the associated Channel.<br />
• EQ led lit means the signal is coming from the associated EQ output.<br />
• KEY led lit means the signal is being taken from an external trigger.<br />
NB:<br />
Whichever Sidechain Input you<br />
select will be common to all the<br />
other available processes.<br />
For example, if you have the<br />
Compressor set to take it's<br />
sidechain from the External Key<br />
Input, then the Gate (and Exp)<br />
will also automatically be set to<br />
the External Key Input.<br />
If you change this selection on<br />
one process, it will impact that<br />
same selection on other<br />
available processes on the same<br />
Channel or Monitor path.<br />
▶ The 3 rd encoder sets the Release time, and operates within a range of<br />
0.1 second to 4 seconds.<br />
▶ By pressing this encoder you can set the Attack time from being 1.5ms<br />
for 40dB of range (Slow) to 100micro seconds for 40dB range (Fast).<br />
▶ The 4 th encoder only swaps the process between acting as a Gate or an<br />
Expander, and this is shown on screen with the EXP button (lit when<br />
acting as an Expander and unlit when acting as a Gate).<br />
F1 – F5 buttons<br />
At the bottom of the DYN screen are function buttons, some of which<br />
match up with the F1 to F5 buttons just below the 4 DYN encoders.<br />
Please see the EQ section for a full explanation of these buttons functions,<br />
page 97.<br />
NB:<br />
With regard to linking the Dynamics, it is irrelevant whether the Dynamics<br />
are operating on the channel input or DAW input sections.<br />
- 101 -