Genesys User Manual - AMS Neve

More documents

Recommendations

Info

I/P 2 DMON does exactly the same as I/P 2 mode but now feeds the <strong>Neve</strong> FireWire output into the console monitor return input allowing for <strong>Neve</strong> FireWire mixdown. - 66 -
ROUTE SEL Section This section enables the setup routing to the 8T and Main Mix Outputs, plus simple storing and loading of console snapshot stores. FILING Lights yellow, and acts as the On/Off for this panel allowing Stores to be saved or loaded via the stores screen. LOAD On the first press, it will turn the TFT screen over to the Snapshot/Recall Stores page where a file can be selected. Once a selection has been made on screen, then pressing the button again will load that particular Store to the console via the Load Store pop-up. SAVE On the first press, it will turn the screen over to the Store Recall screen. It will then be possible to create a Store. On the second press, a dialogue screen will ask you to name the file so the store can be saved as a future starting template. ▶ Enter a filename and then click SAVE. - 67 -
Page 1 and 2:
GENESYS User Manual Issue 1.13.1 Ve
Page 3 and 4:
Servicing is required when the appa
Page 5 and 6:
Health & Safety Notice FOR YOUR OWN
Page 7 and 8:
Console Overview A 16 fader console
Page 9 and 10:
Table of Contents IMPORTANT SAFTY I
Page 11 and 12:
MONO...............................
Page 13 and 14:
PC.................................
Page 15 and 16: About this manual This manual consi
Page 17 and 18: The Computer Cassette IMPORTANT: Be
Page 19 and 20: Optional Console Hardware EQ Casset
Page 21 and 22: Channels Digital Converter System (
Page 23 and 24: Optional Software Packages Automati
Page 25 and 26: Wiring connections / Setup for DAW
Page 27 and 28: DAW Computer Settings Mac OS X (DAW
Page 29 and 30: After installation the driver ports
Page 31 and 32: There are two audio connectors on e
Page 33 and 34: Master SEL mode ▶ Master SEL mode
Page 35 and 36: An Overview of the Genesys Signal F
Page 37 and 38: Recording in Stereo ▶ Before powe
Page 39 and 40: Mixing In Surround If you have LCR
Page 41 and 42: Surround system. ▶ Ensure that th
Page 43 and 44: The speaker button will light when
Page 45 and 46: will be able to swap between listen
Page 47 and 48: 90Hz filter Switches a hi pass filt
Page 49 and 50: Channel and Monitor Path Drag and D
Page 51 and 52: DIRECT OUTPUT Section Master Level
Page 53 and 54: CH Allows you to send the Channel i
Page 55 and 56: REVERB RETURNS / AUX MASTERS Sectio
Page 57 and 58: AUX MASTERS Section Master Send Set
Page 59 and 60: Master SEL mode on the 8T AUXES Sec
Page 61 and 62: 2T/MIX Sends tone to the 2T and Mix
Page 63 and 64: MASTER SEL Section LOCK ▶ Lights
Page 65: Momentary Solo mode is also availab
Page 69 and 70: ▶ For later LCR/Stereo channel st
Page 71 and 72: CUE MIX Section Each of the Cue mix
Page 73 and 74: CONTROL ROOM MONITOR Section Sets t
Page 75 and 76: EXT ▶ Will light yellow when sele
Page 77 and 78: It is possible to tie a set of loud
Page 79 and 80: • 30% indicates you are listening
Page 81 and 82: To Lock Relative Levels Within a Lo
Page 83 and 84: setups using LOCK/RTE SEL, can be s
Page 85 and 86: DAW / CONSOLE CONTROL Screen The Mo
Page 87 and 88: have the following functions: Encod
Page 89 and 90: 8T Faders The 8T faders can either
Page 91 and 92: Meterbridge CHANNEL Meters Each fad
Page 93 and 94: of each meter. PPM Sets all meter i
Page 95 and 96: Master Screen The SETUP screen allo
Page 97 and 98: At the bottom of the EQ screen are
Page 99 and 100: DYN Only functions if at least one
Page 101 and 102: Gate/Expander The Dynamics screen i
Page 103 and 104: DAW Setup and control for the Digit
Page 105 and 106: Speaker Trims ▶ Click the speaker
Page 107 and 108: NB: 1 - When setting levels using t
Page 109 and 110: FILING Provides facility to Save an
Page 111 and 112: RTE This screen is a graphic repres
Page 113 and 114: RECALL Recall Overview Recall is an
Page 115 and 116: Saving a Recall file In effect, a R
Page 117 and 118:
Hold mode / Auto mode The above pro
Page 119 and 120:
Important Information There are two
Page 121 and 122:
This is a two-function button, and
Page 123 and 124:
AD/DA & FireWire System Digital Con
Page 125 and 126:
Channel Master Overview The Channel
Page 127 and 128:
Serial In / Out Provided for daisy-
Page 129 and 130:
Channel Slave Overview The Slave AD
Page 131 and 132:
Monitor Section Overview This card
Page 133 and 134:
Switchblock Contains 4 switches, th
Page 135 and 136:
This zip file contains a single dri
Page 137 and 138:
1 - 8 9 - 16 17 - 24 25 - 32 Monito
Page 139 and 140:
Monitor card This card will always
Page 141 and 142:
CAT 5 connections on systems withou
Page 143 and 144:
FireWire From DAW A B A B A B A B A
Page 145 and 146:
The install will start and the prog
Page 147 and 148:
Software Operation ▶ When the Gen
Page 149 and 150:
andwidth is limited and the capabil
Page 151 and 152:
Channels DLINE Input This covers wh
Page 153 and 154:
⌥ On the console surface, the dig
Page 155 and 156:
Windows 7 Drivers This section only
Page 157 and 158:
Recommended OHCI Chipsets To get th
Page 159 and 160:
Channel Controls Each channel can b
Page 161 and 162:
Rear Connectors / Pin-out informati
Page 163 and 164:
Female XLR 3 9 Insert IN 3 hot 2 3
Page 165 and 166:
Connecting the 4081 to Genesys with
Page 167 and 168:
▶ Click Settings Within Software
Page 169 and 170:
Digital Audio Workstation (DAW) Con
Page 171 and 172:
encoder, it will toggle the selecte
Page 173 and 174:
TRANSPORT The Transport buttons on
Page 175 and 176:
Control and click Add. This will ad
Page 177 and 178:
switched over to showing the meteri
Page 179 and 180:
y looking at Logic Pro and Genesys
Page 181 and 182:
already) to indicate you have selec
Page 183 and 184:
automation mode. ▶ Pressing the f
Page 185 and 186:
▶ In the left Devices column sele
Page 187 and 188:
DAW Metering (Genesys software ) Wh
Page 189 and 190:
▶ F1, F2 or the fader SEL buttons
Page 191 and 192:
◀ and ▶ Buttons They are used t
Page 193 and 194:
▶ A pop-up will appear on screen
Page 195 and 196:
USB Recovery - Complete Software Re
Page 197 and 198:
Integrated Peripherals Menu OnChip
Page 199 and 200:
The Recovery Process ▶ Once the s
Page 201 and 202:
Audio Monitoring Boards Accessible
Page 203 and 204:
Monitor Board 2 (Mix Insert) This b
Page 205 and 206:
Genesys Audio Specification Record
Page 207 and 208:
Genesys Physical Information Dimens
Page 209 and 210:
1 Screen 2 Hi 3 Lo RS 232 9-pin D-t
Page 211 and 212:
Loudspeaker Outputs A & M1 (25-way
Page 213 and 214:
Console Outputs - 8Ts (25-way D-typ
Page 215 and 216:
Channel Section Connectors As shown
Page 217 and 218:
Channel Insert 2 Send (25-way D-typ
Page 219 and 220:
Master AD/DA Channels cassette, SMN
Page 221 and 222:
Slave AD/DA Channels cassette AES R
Page 223 and 224:
AES TX / AUX / 2T L & R / MIX L & R
Page 225 and 226:
General Fuses - Ratings & Location
Page 227 and 228:
Alphabetical Index 1 1/2...........
Page 229 and 230:
I/P 2..............................
Page 231 and 232:
To DAW via FireWire................
show all

Genesys User Manual - AMS Neve

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?