Genesys User Manual - AMS Neve

More documents

Recommendations

Info

Console Connector pin-outs Computer Cassette USB 1 +5v Red 2 - Data White 3 + Data Green 4 GND Black Mouse 1 - Data 2 N/C 3 GND 4 +5v 5 + Data / Clock 6 N/C Shell Shield Keyboard 1 Keyboard data (+5v signal level) 2 Keyboard reset (not used) 3 Ground (0v) 4 +5v 5 Keyboard clock (+5v signal) 6 N/C Shell Shield RJ 45 Twisted pair networking 1 TX + 2 TX - 3 RX + 4 BD3 + 5 BD3 - 6 RX - 7 BD4 + 8 BD4 - Timecode XLR - 208 -
1 Screen 2 Hi 3 Lo RS 232 9-pin D-type 1 Ext RS 485 Data - 2 Ext RS 485 Data + 3 NC 4 Reserved 5 Signal Ground 6 Relay Contact 1 7 Relay Contact 2 8 NC 9 Reserved Relays 1 & 2 are a closing set of contacts operated by the EXT button on the <strong>Genesys</strong> keypad. This facility is used for switching the VGA feeds (one each from <strong>Genesys</strong> and the DAW) to enable the system to operate on one TFT screen for both machines. VGA Hi-density 15-way D-type 1 Red 0 – 0.7v 2 Green 0 – 0.7v 3 Blue 0 – 0.7v 4 N/C 5 Digital ground 6 Red Return Analogue ground 7 Green Return Analogue ground 8 Blue Return Analogue ground 9 N/C 10 Digital ground 11 N/C 12 N/C 13 Horizontal sync TTL 14 Vertical sync TTL 15 N/C - 209 -
Page 1 and 2:
GENESYS User Manual Issue 1.13.1 Ve
Page 3 and 4:
Servicing is required when the appa
Page 5 and 6:
Health & Safety Notice FOR YOUR OWN
Page 7 and 8:
Console Overview A 16 fader console
Page 9 and 10:
Table of Contents IMPORTANT SAFTY I
Page 11 and 12:
MONO...............................
Page 13 and 14:
PC.................................
Page 15 and 16:
About this manual This manual consi
Page 17 and 18:
The Computer Cassette IMPORTANT: Be
Page 19 and 20:
Optional Console Hardware EQ Casset
Page 21 and 22:
Channels Digital Converter System (
Page 23 and 24:
Optional Software Packages Automati
Page 25 and 26:
Wiring connections / Setup for DAW
Page 27 and 28:
DAW Computer Settings Mac OS X (DAW
Page 29 and 30:
After installation the driver ports
Page 31 and 32:
There are two audio connectors on e
Page 33 and 34:
Master SEL mode ▶ Master SEL mode
Page 35 and 36:
An Overview of the Genesys Signal F
Page 37 and 38:
Recording in Stereo ▶ Before powe
Page 39 and 40:
Mixing In Surround If you have LCR
Page 41 and 42:
Surround system. ▶ Ensure that th
Page 43 and 44:
The speaker button will light when
Page 45 and 46:
will be able to swap between listen
Page 47 and 48:
90Hz filter Switches a hi pass filt
Page 49 and 50:
Channel and Monitor Path Drag and D
Page 51 and 52:
DIRECT OUTPUT Section Master Level
Page 53 and 54:
CH Allows you to send the Channel i
Page 55 and 56:
REVERB RETURNS / AUX MASTERS Sectio
Page 57 and 58:
AUX MASTERS Section Master Send Set
Page 59 and 60:
Master SEL mode on the 8T AUXES Sec
Page 61 and 62:
2T/MIX Sends tone to the 2T and Mix
Page 63 and 64:
MASTER SEL Section LOCK ▶ Lights
Page 65 and 66:
Momentary Solo mode is also availab
Page 67 and 68:
ROUTE SEL Section This section enab
Page 69 and 70:
▶ For later LCR/Stereo channel st
Page 71 and 72:
CUE MIX Section Each of the Cue mix
Page 73 and 74:
CONTROL ROOM MONITOR Section Sets t
Page 75 and 76:
EXT ▶ Will light yellow when sele
Page 77 and 78:
It is possible to tie a set of loud
Page 79 and 80:
• 30% indicates you are listening
Page 81 and 82:
To Lock Relative Levels Within a Lo
Page 83 and 84:
setups using LOCK/RTE SEL, can be s
Page 85 and 86:
DAW / CONSOLE CONTROL Screen The Mo
Page 87 and 88:
have the following functions: Encod
Page 89 and 90:
8T Faders The 8T faders can either
Page 91 and 92:
Meterbridge CHANNEL Meters Each fad
Page 93 and 94:
of each meter. PPM Sets all meter i
Page 95 and 96:
Master Screen The SETUP screen allo
Page 97 and 98:
At the bottom of the EQ screen are
Page 99 and 100:
DYN Only functions if at least one
Page 101 and 102:
Gate/Expander The Dynamics screen i
Page 103 and 104:
DAW Setup and control for the Digit
Page 105 and 106:
Speaker Trims ▶ Click the speaker
Page 107 and 108:
NB: 1 - When setting levels using t
Page 109 and 110:
FILING Provides facility to Save an
Page 111 and 112:
RTE This screen is a graphic repres
Page 113 and 114:
RECALL Recall Overview Recall is an
Page 115 and 116:
Saving a Recall file In effect, a R
Page 117 and 118:
Hold mode / Auto mode The above pro
Page 119 and 120:
Important Information There are two
Page 121 and 122:
This is a two-function button, and
Page 123 and 124:
AD/DA & FireWire System Digital Con
Page 125 and 126:
Channel Master Overview The Channel
Page 127 and 128:
Serial In / Out Provided for daisy-
Page 129 and 130:
Channel Slave Overview The Slave AD
Page 131 and 132:
Monitor Section Overview This card
Page 133 and 134:
Switchblock Contains 4 switches, th
Page 135 and 136:
This zip file contains a single dri
Page 137 and 138:
1 - 8 9 - 16 17 - 24 25 - 32 Monito
Page 139 and 140:
Monitor card This card will always
Page 141 and 142:
CAT 5 connections on systems withou
Page 143 and 144:
FireWire From DAW A B A B A B A B A
Page 145 and 146:
The install will start and the prog
Page 147 and 148:
Software Operation ▶ When the Gen
Page 149 and 150:
andwidth is limited and the capabil
Page 151 and 152:
Channels DLINE Input This covers wh
Page 153 and 154:
⌥ On the console surface, the dig
Page 155 and 156:
Windows 7 Drivers This section only
Page 157 and 158: Recommended OHCI Chipsets To get th
Page 159 and 160: Channel Controls Each channel can b
Page 161 and 162: Rear Connectors / Pin-out informati
Page 163 and 164: Female XLR 3 9 Insert IN 3 hot 2 3
Page 165 and 166: Connecting the 4081 to Genesys with
Page 167 and 168: ▶ Click Settings Within Software
Page 169 and 170: Digital Audio Workstation (DAW) Con
Page 171 and 172: encoder, it will toggle the selecte
Page 173 and 174: TRANSPORT The Transport buttons on
Page 175 and 176: Control and click Add. This will ad
Page 177 and 178: switched over to showing the meteri
Page 179 and 180: y looking at Logic Pro and Genesys
Page 181 and 182: already) to indicate you have selec
Page 183 and 184: automation mode. ▶ Pressing the f
Page 185 and 186: ▶ In the left Devices column sele
Page 187 and 188: DAW Metering (Genesys software ) Wh
Page 189 and 190: ▶ F1, F2 or the fader SEL buttons
Page 191 and 192: ◀ and ▶ Buttons They are used t
Page 193 and 194: ▶ A pop-up will appear on screen
Page 195 and 196: USB Recovery - Complete Software Re
Page 197 and 198: Integrated Peripherals Menu OnChip
Page 199 and 200: The Recovery Process ▶ Once the s
Page 201 and 202: Audio Monitoring Boards Accessible
Page 203 and 204: Monitor Board 2 (Mix Insert) This b
Page 205 and 206: Genesys Audio Specification Record
Page 207: Genesys Physical Information Dimens
Page 211 and 212: Loudspeaker Outputs A & M1 (25-way
Page 213 and 214: Console Outputs - 8Ts (25-way D-typ
Page 215 and 216: Channel Section Connectors As shown
Page 217 and 218: Channel Insert 2 Send (25-way D-typ
Page 219 and 220: Master AD/DA Channels cassette, SMN
Page 221 and 222: Slave AD/DA Channels cassette AES R
Page 223 and 224: AES TX / AUX / 2T L & R / MIX L & R
Page 225 and 226: General Fuses - Ratings & Location
Page 227 and 228: Alphabetical Index 1 1/2...........
Page 229 and 230: I/P 2..............................
Page 231 and 232: To DAW via FireWire................
show all

Genesys User Manual - AMS Neve

Create successful ePaper yourself

Delete template?

Save as template?