LTV 1100 Operator Manual - CareFusion

More documents

Recommendations

Info

Patient Assist Call System – Connection Instructions The ventilator is configured to interface with a Patient Assist Call system requiring either normallyclosed or normally-open contact sets. Devices connected to the Patient Assist port must be IEC 60601-1-1 certified. If your patient assist system is Normally Open, use Patient Assist Cable, Normally Open P/N 10780. If your patient assist system is Normally Closed, use Patient Assist Cable, Normally Closed P/N 10779. To connect the ventilator to the patient assist system: 1) Insert the telephone jack connector (RJ11-4) into the port labeled PATIENT ASSIST on the left hand side of the ventilator. 2) Connect the jack on the other end of the cable to your patient assist system. 3) Test the connection by performing an Alarm test (see Chapter 11 - Ventilator Checkout Tests) or by causing an alarm and verifying the patient assist call activates. WARNING Unapproved Adapters – Only CareFusion Accessories should be used to connect the ventilator to Patient Assist Call Systems. These accessories incorporate safety features to reduce the risk of shock. Do not attempt to modify these accessories in any way. Patient Assist Call Connector – Do not apply more than 25V rms or 32VDC to the Patient Assist Call connector. AVERTISSEMENT Accessoires non approuvés – L’utilisation d’accessoires qui ne sont pas expressément approuvés par CareFusion pourrait entraîner des conditions dangereuses. Seuls les accessoires de CareFusion devraient être utilisés pour brancher les ventilateurs aux systèmes d’aide aux patients. Ces accessoires comportent des caractéristiques de sécurité pour réduire les risques de choc. N’essayez pas de modifier ces accessoires d’aucune façon. Connecteur d’appel d’aide aux patients – Ne mettez pas plus de 25 V efficace ou 32 V c.c. au connecteur d’appel d’aide aux patients. 21106-001, Rev. E Operator’s Manual - LTV ® 1100 Ventilator C-15
Communications Port The Communications Port on the LTV ® 1100 ventilator allows for attachment to, and communication with, accessories such as graphics monitors or printers. Currently the printer option is only available for use by service personnel. Use the Communications Setting option in the Extended Features menu to modify the communications protocol (see Chapter 10 - Extended Features, Communications Setting for instructions). LTM Graphics Monitor The LTM Graphics Monitor is a thin, lightweight color graphics monitor accessory for LTM compatible LTV ® ventilators. For additional information regarding the LTM Graphics Monitor, contact CareFusion. To install and setup an LTM Graphics Monitor, refer to the LTM Graphics Monitor Operator’s Manual included with your Monitor. C-16 Operator’s Manual - LTV ® 1100 Ventilator 21106-001 Rev. E
Page 1 and 2:
LTV ® 1100 Ventilator Operator’s
Page 3 and 4:
Warranty CareFusion warrants that t
Page 5 and 6:
Notice To Operators Unsafe Operatio
Page 7 and 8:
Breath Rate .......................
Page 9 and 10:
High Pressure Alarm Delay .........
Page 11 and 12:
Installation and Setup ............
Page 13 and 14:
Operator’s Safety Information All
Page 15 and 16:
WARNING Battery run time - When the
Page 17 and 18:
AVERTISSEMENT Personnel non qualifi
Page 19 and 20:
AVERTISSEMENT Modes Vérification e
Page 21 and 22:
Cautions CAUTION Ventilator Sterili
Page 23 and 24:
CAUTION External Battery Pack - The
Page 25 and 26:
ATTENTION Nettoyage du panneau fron
Page 27 and 28:
Symbols Symbol Compliance 1 Title A
Page 29 and 30:
Indications for Use The LTV ® 1100
Page 31 and 32:
Information/Assistance For addition
Page 33 and 34:
Volume Control Breaths For Volume C
Page 35 and 36:
Spontaneous Breaths For Spontaneous
Page 37 and 38:
SIMV Mode SIMV mode is selected whe
Page 39 and 40:
NPPV Mode The ventilator provides N
Page 41 and 42:
Volume Ventilation The LTV ® 1100
Page 43 and 44:
Setting a Control There are 5 kinds
Page 45 and 46:
Bright, Dim and Blank Control Displ
Page 47 and 48:
Control Locking The front panel con
Page 49 and 50:
Breath Rate Use the Breath Rate con
Page 51 and 52:
High Pressure Limit Use the High Pr
Page 53 and 54:
Low Pressure The Low Pressure alarm
Page 55 and 56:
On/Standby This button switches the
Page 57 and 58:
PEEP Control The PEEP control estab
Page 59 and 60:
Select Use this button to change th
Page 61 and 62:
Set Value Knob Use the Set Value kn
Page 63 and 64:
Tidal Volume Use the Tidal Volume c
Page 65 and 66:
6-18 Operator’s Manual - LTV ® 1
Page 67 and 68:
Battery Level The Battery Level ind
Page 69 and 70:
Charge Status The Charge Status ind
Page 71 and 72:
NPPV The NPPV 20 indicator LED is l
Page 73 and 74:
Automatic or Manual Data Display Sc
Page 75 and 76:
I:Ecalc xx:xx The Calculated I:E ra
Page 77 and 78:
Alarms APNEA, APNEA xx bpm When the
Page 79 and 80:
BAT EMPTY (cont.) NOTE When the bat
Page 81 and 82:
BAT LOW (cont) NOTE Internal Batter
Page 83 and 84:
DEFAULTS (cont.) The factory-set de
Page 85 and 86:
DISC/SENSE When the ventilator dete
Page 87 and 88:
HIGH PEEP When the patient circuit
Page 89 and 90:
High PRES (cont.) The HIGH PRES ala
Page 91 and 92:
INOP An INOP alarm is generated whe
Page 93 and 94:
LOW PEEP When the patient circuit p
Page 95 and 96:
NO CAL DATA, NO CAL Monitor Display
Page 97 and 98:
POWER LOW When the ventilator is op
Page 99 and 100:
RESET / RESET 1 A RESET or a RESET
Page 101 and 102:
SBT > f When the Spontaneous Breath
Page 103 and 104:
SBT > f/Vt When the Spontaneous Bre
Page 105 and 106:
XDCR FAULT When a transducer autoze
Page 107 and 108:
H&L PEEP OFF The H&L PEEP OFF messa
Page 109 and 110:
LO f/Vt OFF The LO f/Vt OFF message
Page 111 and 112:
SBT TIME The SBT TIME message is di
Page 113 and 114:
Navigating the Extended Features Me
Page 115 and 116:
Apnea Interval Use this menu item t
Page 117 and 118:
Patient Assist Use the PNT ASSIST m
Page 119 and 120:
Variable Rise Time Use the Variable
Page 121 and 122:
Variable Time Termination Use the V
Page 123 and 124:
Leak Compensation Use the Leak Comp
Page 125 and 126:
Control Unlock Use the Control Unlo
Page 127 and 128:
Set Date Use the Set Date option to
Page 129 and 130:
PIP LED Use the PIP LED option to t
Page 131 and 132:
Sigh Breath Use the Sigh Breath fea
Page 133 and 134:
Turning Leak Test Query on or off 1
Page 135 and 136:
SBT Operations (cont.) When the Spo
Page 137 and 138:
SBT Quick Start Feature In addition
Page 139 and 140:
Bi-directional Flow Transducer Diff
Page 141 and 142:
Real Time Transducers Use the Real
Page 143 and 144:
10-32 Operator’s Manual - LTV ®
Page 145 and 146:
To enable the Ventilator Checkout m
Page 147 and 148:
Display Test Use the Display Test t
Page 149 and 150:
Control Test Use the Control Test t
Page 151 and 152:
Leak Test Use the Leak Test to test
Page 153 and 154:
Vent Inop Alarm Test Use the Vent I
Page 155 and 156:
Exit To exit the vent check mode an
Page 157 and 158:
AVERTISSEMENT Mode de circuit du pa
Page 159 and 160:
The Power On Self Tests 43 (POST) a
Page 161 and 162:
Procedure for Control Mode Set Up S
Page 163 and 164:
Procedure for SIMV Mode Set Up Set
Page 165 and 166:
Procedure for NPPV Mode Set Up Set
Page 167 and 168:
LTV ® Ventilator Settings Checklis
Page 169 and 170:
Cleaning or replacing the Fan Filte
Page 171 and 172:
Cleaning the Exhalation Valve and R
Page 173 and 174:
ATTENTION Nettoyage du piège à ea
Page 175 and 176:
To clean the exhalation valve, sens
Page 177 and 178:
Page 179 and 180:
Using the AC Adapter To run the ven
Page 181 and 182:
2) Connect the power connector on t
Page 183 and 184:
Using the Automobile Cigarette Ligh
Page 185 and 186:
CAUTION Release Button - To avoid d
Page 187 and 188:
Replacing the Automobile Adapter Fu
Page 189 and 190:
Page 191 and 192:
Displays and Buttons Some of the sy
Page 193 and 194:
Symptoms Possible Causes What to Do
Page 195 and 196: Ventilator Performance Symptoms Pos
Page 197 and 198: Symptoms Possible Causes What to Do
Page 203 and 204: Power and Battery Operation Problem
Page 205 and 206: Alarms Many alarms such as HIGH PRE
Page 215 and 216: 15-26 Operator’s Manual - LTV ®
Page 217 and 218: Control Range Tolerance Tidal Volum
Page 219 and 220: Fixed Alarms Control Range Toleranc
Page 221 and 222: Displays Display Range Tolerance Ai
Page 223 and 224: Power Feature Range Tolerance / Ind
Page 225 and 226: EMC and RF Environments The followi
Page 227 and 228: Table 203 - 60601-1-2 © IEC:2001(E
Page 229 and 230: A-14 Operator’s Manual - LTV ® 1
Page 231 and 232: Service Assistance For assistance i
Page 233 and 234: Protective Boots Rubberized protect
Page 235 and 236: Item (1), Protective Boot, Upper (1
Page 237 and 238: Protective Boot Installation Suppli
Page 239 and 240: To Install the Lower Protective Boo
Page 241 and 242: Patient Breathing Circuit - Connect
Page 243 and 244: Low Pressure O 2 Source This option
Page 245: Low Pressure O 2 Source (cont.) To
Page 249 and 250: 3) If the remote alarm has a male B
Page 251 and 252: Ventilator Settings and Procedure P
Page 253 and 254: Procedure: Set the Low Min. Vol. al
Page 255 and 256: Ventilation flow enters the Flow Va
Page 257 and 258: 5) Push the Select button. xx:even
Page 259 and 260: Code Event Name Event Associated Al
Page 261 and 262: Event Codes by Event Name Event Nam
Page 263 and 264: Event Name Code Event Associated Al
Page 265 and 266: TERM Control mode CPAP CPAP mode Di
Page 267 and 268: TERM Pressure support breath Pressu
Page 269 and 270: C Calculated Peak Flow · 6-16, 8-2
Page 271 and 272: NPPV Mode · 4-4, 10-11 Indicator
show all

LTV 1100 Operator Manual - CareFusion

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?