- Page 1 and 2:
Controls, Start-Up, Operation, Serv
- Page 3 and 4:
WARNING What to do if you smell gas
- Page 5 and 6:
and the ENTER keys until the desire
- Page 7 and 8:
START-UP IMPORTANT: Do not attempt
- Page 9 and 10:
Table 4 — Fan Performance — 48P
- Page 11 and 12:
Table 6 — Fan Performance — 48P
- Page 13 and 14:
Table 8 — Fan Performance — 48P
- Page 15 and 16:
AIRFLOW (cfm) Table 10 — Fan Perf
- Page 17 and 18:
AIRFLOW (cfm) Table 12 — Fan Perf
- Page 19 and 20:
AIRFLOW (cfm) Table 14 — Fan Perf
- Page 21 and 22:
AIRFLOW (cfm) Table 16 — Fan Perf
- Page 23 and 24:
AIRFLOW (Cfm) LEGEND Table 18 — F
- Page 25 and 26:
AIRFLOW (Cfm) LEGEND Table 20 — F
- Page 27 and 28:
AIRFLOW (Cfm) LEGEND Table 22 — F
- Page 29 and 30:
AIRFLOW (cfm) LEGEND Bhp — Brake
- Page 31 and 32:
HIGH-EFFICIENCY MOTORS Nominal Maxi
- Page 33 and 34:
2. Under the Setpoints menu, set th
- Page 35 and 36:
would use Period 2 and set days Sat
- Page 37 and 38:
there is a loss of communication be
- Page 39 and 40:
and when ON, the control sets a cap
- Page 41 and 42:
System Mode Test — When the syste
- Page 43 and 44:
Table 31 — Unit Configuration ITE
- Page 45 and 46:
SETTING UP THE SYSTEM Machine Contr
- Page 47 and 48:
High SST Alert Delay Time (H.SST)
- Page 49 and 50:
Table 36 — Cool/Heat Set Point Of
- Page 51 and 52:
Table 38 — Run Status Cool Displa
- Page 53 and 54:
To use Demand Limiting, select the
- Page 55 and 56:
Size 050, 055, 060 Contactor OFM(s)
- Page 57 and 58:
Whenever the outdoor ambient temper
- Page 59 and 60:
Demand Level Low Heat Off Offset (L
- Page 61 and 62:
Limit Switch Low Temp (SW.L.T) —
- Page 63 and 64:
STAGE Table 49 — IGC LED Indicato
- Page 65 and 66:
Table 50 — Static Pressure Contro
- Page 67 and 68:
Table 53 — Dirty Filter Switch Po
- Page 69 and 70:
NOTE: If the user wishes to disable
- Page 71 and 72:
the economizer modulates when attem
- Page 73 and 74:
P = K * BP.P * (error) I = K * BP.I
- Page 75 and 76:
its smoke. Closing the economizer (
- Page 77 and 78:
Table 57 — Indoor Air Quality Con
- Page 79 and 80:
Table 58 — Humidity Configuration
- Page 81 and 82:
The default sensor is the return ai
- Page 83 and 84:
TEMPERATURE COMPENSATED START LOGIC
- Page 85 and 86:
Sensor Trim Configuration — The T
- Page 87 and 88:
SUPPLY FAN VFD CONFIGURATION — Th
- Page 89 and 90:
REMOTE SWITCH LOGIC CONFIGURATION (
- Page 91 and 92:
Alarms and Alarm History for for an
- Page 93 and 94:
Transducer Troubleshooting — The
- Page 95 and 96:
Table 75 — 10K Thermistor vs Resi
- Page 97 and 98:
TEMP RESISTANCE (F) (Ohms) -25 98,0
- Page 99 and 100:
PRESSURE (PSIG) Table 80 — Suctio
- Page 101 and 102:
Table 81 — Discharge Pressure Tra
- Page 103 and 104:
Table 82 — Auto View of Run Statu
- Page 105 and 106:
Table 84 — Cooling Information Di
- Page 107 and 108: equalize compressor oil levels. If
- Page 109 and 110: Table 91 — Alert and Alarm Codes
- Page 111 and 112: T072 (Evaporator Discharge Reset Se
- Page 113 and 114: This alarm will disable mechanical
- Page 115 and 116: This is the reverse of the Pressuri
- Page 117 and 118: 117 a48-8408 Fig. 19 — Typical Po
- Page 119 and 120: OD ENTHALPY SWITCH LOW REMOTE OCCUP
- Page 121 and 122: Fig. 23 — Typical Electric Heat U
- Page 123 and 124: 123 Fig. 25 — Typical Gas Heat Se
- Page 125 and 126: 125 Fig. 27 — Component Arrangeme
- Page 127 and 128: ACCSY — Accessory ACC’Y — Acc
- Page 129 and 130: Table 93 — Rooftop Control Board
- Page 131 and 132: Table 96 — Control Expansion Modu
- Page 133 and 134: LEGEND IAQ — Indoor Air Quality V
- Page 135 and 136: the motor position to be configured
- Page 137 and 138: TIME EWT LWT SETP Run Status Servic
- Page 139 and 140: Fig. 37 — Door Latch Fig. 38 —
- Page 141 and 142: SUPPLY FAN AND POWER EXHAUST MOTOR
- Page 143 and 144: Routine cleaning of coil surfaces i
- Page 145 and 146: Saturated Discharge Temperature (de
- Page 147 and 148: Saturated Discharge Temperature (de
- Page 149 and 150: Saturated Discharge Temperature (de
- Page 151 and 152: Saturated Discharge Temperature (de
- Page 153 and 154: Saturated Discharge Temperature (de
- Page 155 and 156: Saturated Discharge Temperature (de
- Page 157: Saturated Discharge Temperature (de
- Page 161 and 162: Saturated Discharge Temperature (de
- Page 163 and 164: Gas System Adjustment (48P Only) GA
- Page 165 and 166: APPENDIX A — LOCAL DISPLAY TABLES
- Page 167 and 168: APPENDIX A — LOCAL DISPLAY TABLES
- Page 169 and 170: APPENDIX A — LOCAL DISPLAY TABLES
- Page 171 and 172: APPENDIX A — LOCAL DISPLAY TABLES
- Page 173 and 174: APPENDIX A — LOCAL DISPLAY TABLES
- Page 175 and 176: APPENDIX A — LOCAL DISPLAY TABLES
- Page 177 and 178: APPENDIX B — CCN TABLES (cont) ST
- Page 179 and 180: APPENDIX B — CCN TABLES (cont) ST
- Page 181 and 182: APPENDIX B — CCN TABLES (cont) SE
- Page 183 and 184: APPENDIX B — CCN TABLES (cont) SE
- Page 185 and 186: APPENDIX B — CCN TABLES (cont) SE
- Page 187 and 188: APPENDIX B — CCN TABLES (cont) MA
- Page 189 and 190: APPENDIX B — CCN TABLES (cont) MA
- Page 191 and 192: TESTACTC TESTCOOL TESTFANS TESTHEAT
- Page 193 and 194: APPENDIX C — UNIT STAGING TABLES
- Page 195 and 196: * 41 for Supply Fan Motor VFD, 42 f
- Page 197 and 198: Fig. B — VFD Keypad START UP WITH
- Page 199 and 200: Upload All Parameters — To upload
- Page 201 and 202: To replace the main fan for frame s
- Page 203 and 204: ALARM CODE ALARM NAME IN PANEL 2001
- Page 205 and 206: APPENDIX E — MODE SELECTION PROCE
- Page 207 and 208: CONTROLS SET POINT AND CONFIGURATIO
- Page 209 and 210:
CONTROLS SET POINT AND CONFIGURATIO
- Page 211 and 212:
CONTROLS SET POINT AND CONFIGURATIO
- Page 213 and 214:
CONTROLS SET POINT AND CONFIGURATIO