Controls, Start-Up, Operation, Service and ... - Climayoreo

More documents

Recommendations

Info

APPENDIX B — CCN TABLES (cont) SERVICE-CONFIG TABLES (cont) TABLE DISPLAY NAME RANGE UNITS POINT NAME DEFAULT IAQ_ Economizer Min.Position 0 - 100 % ECONOMIN 5 IAQ Demand Vent Min.Pos. 0 - 100 % IAQMINP 0 Economizer Min.Flow 0 - 20000 CFM OACFMMAX 2000 IAQ Demand Vent Min.Flow 0 - 20000 CFM OACFMMIN 0 Econ.Min.Flow Deadband 200 - 1000 CFM OACFM_DB 400 IAQ Analog Sensor Config 0 - 4 IAQANCFG 0 IAQ 4-20 ma Fan Config 0 - 2 IAQANFAN 0 IAQ Discrete Input Config 0 - 2 IAQINCFG 0 IAQ Disc.In. Fan Config 0 - 2 IAQINFAN 0 OAQ 4-20ma Sensor Config 0 - 2 OAQANCFG 0 IAQ Econo Override Pos. 0 - 100 % IAQOVPOS 100 IAQ Override flow 0 - 31000 CFM IAQOVCFM 10000 Diff.Air Quality LoLimit 0 - 1000 DAQ_LOW 100 Diff. Air Quality HiLimit 100 - 2000 DAQ_HIGH 700 DAQ PPM Fan Off Setpoint 0 - 2000 DAQFNOFF 200 DAQ PPM Fan On Setpoint 0 - 2000 DAQFNON 400 Diff. AQ Responsiveness -5 - 5 IAQREACT 0 OAQ Lockout Value 0 - 2000 OAQLOCK 0 User determined OAQ 0 - 5000 OAQ_USER 400 IAQ Low Reference 0 - 5000 IAQREFL 0 IAQ High Reference 0 - 5000 IAQREFH 2000 OAQ Low Reference 0 - 5000 OAQREFL 0 OAQ High Reference 0 - 5000 OAQREFH 2000 IAQ Purge Yes/No IAQPURGE No IAQ Purge Duration 5-60 min IAQPTIME 15 IAQ Purge LoTemp Min Pos 0-100 % IAQPLTMP 10 IAQ Purge HiTemp Min Pos 0-100 % IAQPHTMP 35 IAQ Purge OAT Lockout 35-70 dF IAQPNTLO 50 SP__ Static Pressure Control Enable/Disable STATICFG Disable Static Pressure Sensor Enable/Disable SPSENS Disable Static Press. Low Range -10 - 0 SP_LOW 0 Static Press. High Range 0 - 10 SP_HIGH 5 Static Pressure Setpoint 0 - 5 "H2O SPSP 1.5 VFD Minimum Speed 0 - 100 % STATPMIN 10 VFD Maximum Speed 0 - 100 % STATPMAX 100 VFD Fire Speed Over. 0 - 100 % STATPFSO 100 Stat. Pres. Reset Config 0 - 4 (multi-text strings) SPRSTCFG 0 SP Reset Ratio 0.00 - 2.00 SPRRATIO 0.20 SP Reset Limit 0.00 - 2.00 SPRLIMIT 0.75 SP Reset Econo. Position 0 - 100 % ECONOSPR 5 Stat.Pres.PID Run Rate 5 - 120 sec SPIDRATE 15 Static Press. Prop. Gain 0 - 5 STATP_PG 0.5 Static Press. Intg. Gain 0 - 2 STATP_IG 0.5 Static Press. Derv. Gain 0 - 5 STATP_DG 0.3 SWLG Filter Status Inpt-Clean Open/Close FLTSLOGC Open IGC Feedback - Off Open/Close GASFANLG Open RemSw Off-Unoc-Strt-NoOv Open/Close RMTINLOG Open Enthalpy Input - Low Open/Close ENTHLOGC Close Fan Status Sw. - Off Open/Close SFSLOGIC Open Dmd.Lmt.Sw.1 - Off Open/Close DMD_SW1L Open Dmd.Lmt.Sw.2 - Off Open/Close DMD_SW2L Open IAQ Disc.Input - Low Open/Close IAQINLOG Open Fire Shutdown - Off Open/Close FSDLOGIC Open Press. Switch - Off Open/Close PRESLOGC Open Evacuation Sw. - Off Open/Close EVACLOGC Open Smoke Purge Sw. - Off Open/Close PURGLOGC Open Dehumidify Sw. - Off Open/Close DHDISCLG Open TRIM Air Temp Lvg SF Trim -10 - 10 ^F SAT_TRIM 0 RAT Trim -10 - 10 ^F RAT_TRIM 0 OAT Trim -10 - 10 ^F OAT_TRIM 0 SPT Trim -10 - 10 ^F SPT_TRIM 0 Limit Switch Trim -10 - 10 ^F LSW_TRIM 0 Air Temp Lvg Evap Trim -10 - 10 ^F CCT_TRIM 0 A1 Discharge Temp Trim -10 - 10 ^F DTA1TRIM Suction Gas Temp A Trim -10 - 10 ^F RGTATRIM Suct.Press.Circ.A Trim -50 - 50 SPA_TRIM 0 Suct.Press.Circ.B Trim -50 - 50 SPB_TRIM 0 Dis.Press.Circ.A Trim -50 - 50 DPA_TRIM 0 Dis.Press.Circ.B Trim -50 - 50 DPB_TRIM 0 Static Press. Trim (ma) -2 - 2 SPMATRIM 0 Bldg. Pressure Trim (ma) -2 - 2 BPMATRIM 0 Outside Air CFM Trim (ma) -2 - 2 OAMATRIM 0 Supply Air CFM Trim (ma) -2 - 2 SAMATRIM 0 Return Air CFM (ma) -2 - 2 RAMATRIM 0 184
APPENDIX B — CCN TABLES (cont) SERVICE-CONFIG TABLES (cont) TABLE DISPLAY NAME RANGE UNITS POINT NAME DEFAULT UNIT Machine Control Type 1-6 CTRLTYPE 4 Unit Size (30-100) 30-100 UNITSIZE 30 Fan Mode (0=auto, 1=cont) 0-1 FAN_MODE 1 Remote Switch Config 0 - 3 RMTINCFG 0 CEM Module Installed Yes/No CEM_BRD No Temp.Cmp.Strt.Cool Factr 0-60 min TCSTCOOL 0 Temp.Cmp.Strt.Heat Factr 0-60 min TCSTHEAT 0 Fan fail shuts down unit Yes/No SFS_SHUT No Fan Stat Monitoring Type 0-2 SFS_MON 0 VAV Unocc.Fan Retry time 0-720 min SAMPMINS 50 50 Hertz Unit ? Yes/No UNIT_HZ No MAT Calc Config Type 0-2 MAT_SEL 1 Reset MAT Table Entries? Yes/No MATRESET No MAT Outside Air Default 0 - 100 % MATOAPOS 20 Altitude……..in feet: 0-60000 ALTITUDE 0 MAT Outside Air Default % MATOAPOS Startup Delay Time 0 - 900 secs DELAY 0 Auxiliary Relay Config 0 - 3 (multi-text strings) AUXRELAY 0 Space Temp Sensor Enable/Disable SPTSENS Disable Space Temp Offset Sensor Enable/Disable SPTOSENS Disable Space Temp Offset Range 1 - 10 SPTO_RNG 5 Space Air RH Sensor Enable/Disable SPRHSENS Disable Return Air RH Sensor Enable/Disable RARHSENS Disable Filter Stat.Sw.Enabled ? Enable/Disable FLTS_ENA Disable VFD_CFG VFD1 Nominal Motor Volts volts VFD1NVLT VFD1 Nominal Motor Amps amps VFD1NAMP VFD1 Nominal Motor Freq VFD1NFRQ VFD1 Nominal Motor RPM VFD1NRPM VFD1 Nominal Motor HPwr VFD1NPWR VFD1 Motor Direction VFD1MDIR VFD1 Acceleration Time sec VFD1ACCL VFD1 Deceleration Time sec VFD1DECL VFD1 Switching Frequency VFD1SWFQ VFD1 Type VFD1TYPE VFD2 Nominal Motor Volts volts VFD2NVLT VFD2 Nominal Motor Amps amps VFD2NAMP VFD2 Nominal Motor Freq VFD2NFRQ VFD2 Nominal Motor RPM VFD2NRPM VFD2 Nominal Motor HPwr VFD2NPWR VFD2 Motor Direction VFD2MDIR VFD2 Acceleration Time sec VFD2ACCL VFD2 Deceleration Time sec VFD2DECL VFD2 Switching Frequency VFD2SWFQ VFD2 Type VFD2TYPE generics Target Point Name 8 CHAR ASCII POINT_01 Target Point Name 8 CHAR ASCII POINT_02 Target Point Name 8 CHAR ASCII POINT_03 Target Point Name 8 CHAR ASCII POINT_04 Target Point Name 8 CHAR ASCII POINT_05 Target Point Name 8 CHAR ASCII POINT_06 Target Point Name 8 CHAR ASCII POINT_07 Target Point Name 8 CHAR ASCII POINT_08 Target Point Name 8 CHAR ASCII POINT_09 Target Point Name 8 CHAR ASCII POINT_10 Target Point Name 8 CHAR ASCII POINT_11 Target Point Name 8 CHAR ASCII POINT_12 Target Point Name 8 CHAR ASCII POINT_13 Target Point Name 8 CHAR ASCII POINT_14 Target Point Name 8 CHAR ASCII POINT_15 Target Point Name 8 CHAR ASCII POINT_16 Target Point Name 8 CHAR ASCII POINT_17 Target Point Name 8 CHAR ASCII POINT_18 Target Point Name 8 CHAR ASCII POINT_19 Target Point Name 8 CHAR ASCII POINT_20 185
Page 1 and 2:
Controls, Start-Up, Operation, Serv
Page 3 and 4:
WARNING What to do if you smell gas
Page 5 and 6:
and the ENTER keys until the desire
Page 7 and 8:
START-UP IMPORTANT: Do not attempt
Page 9 and 10:
Table 4 — Fan Performance — 48P
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
AIRFLOW (cfm) Table 10 — Fan Perf
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
AIRFLOW (Cfm) LEGEND Table 18 — F
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
AIRFLOW (cfm) LEGEND Bhp — Brake
Page 31 and 32:
HIGH-EFFICIENCY MOTORS Nominal Maxi
Page 33 and 34:
2. Under the Setpoints menu, set th
Page 35 and 36:
would use Period 2 and set days Sat
Page 37 and 38:
there is a loss of communication be
Page 39 and 40:
and when ON, the control sets a cap
Page 41 and 42:
System Mode Test — When the syste
Page 43 and 44:
Table 31 — Unit Configuration ITE
Page 45 and 46:
SETTING UP THE SYSTEM Machine Contr
Page 47 and 48:
High SST Alert Delay Time (H.SST)
Page 49 and 50:
Table 36 — Cool/Heat Set Point Of
Page 51 and 52:
Table 38 — Run Status Cool Displa
Page 53 and 54:
To use Demand Limiting, select the
Page 55 and 56:
Size 050, 055, 060 Contactor OFM(s)
Page 57 and 58:
Whenever the outdoor ambient temper
Page 59 and 60:
Demand Level Low Heat Off Offset (L
Page 61 and 62:
Limit Switch Low Temp (SW.L.T) —
Page 63 and 64:
STAGE Table 49 — IGC LED Indicato
Page 65 and 66:
Table 50 — Static Pressure Contro
Page 67 and 68:
Table 53 — Dirty Filter Switch Po
Page 69 and 70:
NOTE: If the user wishes to disable
Page 71 and 72:
the economizer modulates when attem
Page 73 and 74:
P = K * BP.P * (error) I = K * BP.I
Page 75 and 76:
its smoke. Closing the economizer (
Page 77 and 78:
Table 57 — Indoor Air Quality Con
Page 79 and 80:
Table 58 — Humidity Configuration
Page 81 and 82:
The default sensor is the return ai
Page 83 and 84:
TEMPERATURE COMPENSATED START LOGIC
Page 85 and 86:
Sensor Trim Configuration — The T
Page 87 and 88:
SUPPLY FAN VFD CONFIGURATION — Th
Page 89 and 90:
REMOTE SWITCH LOGIC CONFIGURATION (
Page 91 and 92:
Alarms and Alarm History for for an
Page 93 and 94:
Transducer Troubleshooting — The
Page 95 and 96:
Table 75 — 10K Thermistor vs Resi
Page 97 and 98:
TEMP RESISTANCE (F) (Ohms) -25 98,0
Page 99 and 100:
PRESSURE (PSIG) Table 80 — Suctio
Page 101 and 102:
Table 81 — Discharge Pressure Tra
Page 103 and 104:
Table 82 — Auto View of Run Statu
Page 105 and 106:
Table 84 — Cooling Information Di
Page 107 and 108:
equalize compressor oil levels. If
Page 109 and 110:
Table 91 — Alert and Alarm Codes
Page 111 and 112:
T072 (Evaporator Discharge Reset Se
Page 113 and 114:
This alarm will disable mechanical
Page 115 and 116:
This is the reverse of the Pressuri
Page 117 and 118:
117 a48-8408 Fig. 19 — Typical Po
Page 119 and 120:
OD ENTHALPY SWITCH LOW REMOTE OCCUP
Page 121 and 122:
Fig. 23 — Typical Electric Heat U
Page 123 and 124:
123 Fig. 25 — Typical Gas Heat Se
Page 125 and 126:
125 Fig. 27 — Component Arrangeme
Page 127 and 128:
ACCSY — Accessory ACC’Y — Acc
Page 129 and 130:
Table 93 — Rooftop Control Board
Page 131 and 132:
Table 96 — Control Expansion Modu
Page 133 and 134: LEGEND IAQ — Indoor Air Quality V
Page 135 and 136: the motor position to be configured
Page 137 and 138: TIME EWT LWT SETP Run Status Servic
Page 139 and 140: Fig. 37 — Door Latch Fig. 38 —
Page 141 and 142: SUPPLY FAN AND POWER EXHAUST MOTOR
Page 143 and 144: Routine cleaning of coil surfaces i
Page 145 and 146: Saturated Discharge Temperature (de
Page 163 and 164: Gas System Adjustment (48P Only) GA
Page 165 and 166: APPENDIX A — LOCAL DISPLAY TABLES
Page 177 and 178: APPENDIX B — CCN TABLES (cont) ST
Page 179 and 180: APPENDIX B — CCN TABLES (cont) ST
Page 181 and 182: APPENDIX B — CCN TABLES (cont) SE
Page 183: APPENDIX B — CCN TABLES (cont) SE
Page 187 and 188: APPENDIX B — CCN TABLES (cont) MA
Page 189 and 190: APPENDIX B — CCN TABLES (cont) MA
Page 191 and 192: TESTACTC TESTCOOL TESTFANS TESTHEAT
Page 193 and 194: APPENDIX C — UNIT STAGING TABLES
Page 195 and 196: * 41 for Supply Fan Motor VFD, 42 f
Page 197 and 198: Fig. B — VFD Keypad START UP WITH
Page 199 and 200: Upload All Parameters — To upload
Page 201 and 202: To replace the main fan for frame s
Page 203 and 204: ALARM CODE ALARM NAME IN PANEL 2001
Page 205 and 206: APPENDIX E — MODE SELECTION PROCE
Page 207 and 208: CONTROLS SET POINT AND CONFIGURATIO
show all

Controls, Start-Up, Operation, Service and ... - Climayoreo

Create successful ePaper yourself

Delete template?

Save as template?