Controls, Start-Up, Operation, Service and ... - Climayoreo

More documents

Recommendations

Info

APPENDIX B — CCN TABLES (cont) SERVICE-CONFIG TABLES (cont) TABLE DISPLAY NAME RANGE UNITS POINT NAME DEFAULT COOL Enable Compressor A1 Enable/Disable CMPA1ENA Enable Enable Compressor A2 Enable/Disable CMPA2ENA Enable Enable Compressor A3 Enable/Disable CMPA3ENA Enable Enable Compressor B1 Enable/Disable CMPB1ENA Enable Enable Compressor B2 Enable/Disable CMPB2ENA Enable Enable Compressor B3 Enable/Disable CMPB3ENA Enable CSB A1 Feedback Alarm Enable/Disable CSB_A1EN Enable CSB A2 Feedback Alarm Enable/Disable CSB_A2EN Enable CSB A3 Feedback Alarm Enable/Disable CSB_A3EN Enable CSB B1 Feedback Alarm Enable/Disable CSB_B1EN Enable CSB B2 Feedback Alarm Enable/Disable CSB_B2EN Enable CSB B3 Feedback Alarm Enable/Disable CSB_B3EN Enable Capacity Threshold Adjst -10 - 10 Z_GAIN 1 Compressor Lockout Temp -25 - 55 dF OATLCOMP 40 Lead/Lag Configuration LEAD_LAG Motor Master Control ? Yes/No MOTRMAST No Maximum Condenser Temp dF SCT_MAX Minimum Condenser Temp dF SCT_MIN A1 is a Digital Scroll Yes/No DIGCMPA1 A1 Min Digital Capacity % MINCAPA1 Dig Scroll Adjust Delta % DSADJPCT Dig Scroll Adjust Delay sec DSADJDLY Dig Scroll Reduce Delta % DSREDPCT Dig Scroll Reduce Delay sec DSREDDLY Dig Scroll Reduction OAT dF DSREDOAT Dig Scroll Max Only OAT dF DSMAXOAT Min Load Valve Enable Enable/Disable MLV_ENAB Hi SST Alert Delay Time 5 - 30 min HSSTTIME 10 Rev Rotation Verified ? Yes/No REVR_VER Use CSBs for HPS Detect Yes/No CSBHPDET DEHU Dehumidification Config 0-3 DHSELECT 0 Dehumidification Sensor 1-3 DHSENSOR 1 Econ disable in DH mode? Yes/No DHECONEN No Vent Reheat Setpt Select 0-1 DHVHTCFG 0 Vent Reheat RAT offset 0-8 ^F DHVRAOFF 0 Vent Reheat Setpoint 55-95 dF DHVHT_SP 70 Dehumidify Cool Setpoint 40-55 dF DHCOOLSP 45 Dehumidify RH Setpoint 10-90 % DHRELHSP 55 Humidimizer Adjust Rate secs HMZRRATE Humidimizer Prop. Gain HMZR_PG Bypass EXV Max Open % BYP_MAX Condenser EXV Max Open % COND_MAX LAT Sample Buffer Length LAT_SAMP LAT Sample Rate seconds secs LAT_RATE DISP Metric Display Off/On DISPUNIT Off Language Selection 0-1 LANGUAGE 0 Password Enable Enable/Disable PASS_EBL Enable Service Password 0000-9999 PASSWORD 1111 Contrast Adjustment 0-255 CNTR_ADJ 0 Brightness Adjustment 0-255 BRTS_ADJ 0 DLVT Dmd Level Lo Heat On -1 - 2 ^F DMDLHON 1.5 Dmd Level(+) Hi Heat On 0.5 - 20.0 ^F DMDHHON 0.5 Dmd Level(-) Lo Heat Off 0.5 - 2.0 ^F DMDLHOFF 1 Dmd Level Lo Cool On -1 - 2 ^F DMDLCON 1.5 Dmd Level(+) Hi Cool On 0.5 - 20.0 ^F DMDHCON 0.5 Dmd Level(-) Lo Cool Off 0.5 - 2.0 ^F DMDLCOFF 1 Cool Trend Demand Level 0.1 - 5.0 ^F CTRENDLV 0.1 Heat Trend Demand Level 0.1 - 5.0 ^F HTRENDLV 0.1 Cool Trend Time 30 - 600 sec CTRENDTM 120 Heat Trend Time 30 - 600 sec HTRENDTM 120 DMDL Demand Limit Select 0 - 3 DMD_CTRL 0 Demand Limit at 20 ma 0 - 100 % DMT20MA 100 Loadshed Group Number 0 - 99 SHED_NUM 0 Loadshed Demand Delta 0 - 60 % SHED_DEL 0 Maximum Loadshed Time 0 - 120 min SHED_TIM 60 Demand Limit Sw.1 Setpt. 0 - 100 % DLSWSP1 80 Demand Limit Sw.2 Setpt. 0 - 100 % DLSWSP2 50 182
APPENDIX B — CCN TABLES (cont) SERVICE-CONFIG TABLES (cont) TABLE DISPLAY NAME RANGE UNITS POINT NAME DEFAULT ECON Economizer Installed ? Yes/No ECON_ENA Yes Econ. Act.2 Installed ? Yes/No ECON_TWO No Economizer Min.Position 0 - 100 % ECONOMIN 5 Economizer Max.Position 0 - 100 % ECONOMAX 98 Economzr trim for sumZ ? Yes/No ECONTRIM Yes Econ ChangeOver Select 0 - 3 ECON_SEL 0 OA Enthalpy ChgOvr Selct 1 - 5 OAEC_SEL 4 Outdr.Enth Compare Value 18 - 28 BTU/LBM OAEN_CFG 24 High OAT Lockout Temp 55 - 120 dF OAT_LOCK 60 OA Dewpoint Temp Limit 50 - 62 dF OADEWCFG 55 Outside Air RH Sensor Enable/Disable OARHSENS Disable Outdoor Air CFM Sensor Enable/Dsable OCFMSENS Dsable Economizer Min.Flow 0 - 20000 CFM OACFMMAX 2000 IAQ Demand Vent Min.Flow 0 - 20000 CFM OACFMMIN 0 Econ.Min.Flow Deadband 200 - 1000 CFM OACFM_DB 400 Economizer Prop.Gain 0.7 - 3.0 EC_PGAIN 1 Economizer Range Adjust 0.5 - 5 ^F EC_RANGE 2.5 Economizer Speed Adjust 0.1 - 10 EC_SPEED 0.75 Economizer Deadband 0.1 - 2 ^F EC_DBAND 0.5 Unoc Econ Free Cool Cfg 0-2 UEFC_CFG 0 Unoc Econ Free Cool Time 0-720 min UEFCTIME 120 Un.Ec.Free Cool OAT Lock 40-70 dF UEFCNTLO 50 Econ Serial Number 1 0-9999 ECON_SN1 Econ Serial Number 2 0-6 ECON_SN2 Econ Serial Number 3 0-9999 ECON_SN3 Econ Serial Number 4 0-254 ECON_SN4 Econ Ctrl Angle Lo Limit 0-90 ECONCALM 85 Econ 2 Serial Number 1 0-9999 ECN2_SN1 Econ 2 Serial Number 2 0-6 ECN2_SN2 Econ 2 Serial Number 3 0-9999 ECN2_SN3 Econ 2 Serial Number 4 0-254 ECN2_SN4 Ecn2 Ctrl Angle Lo Limit 0-90 ECN2CALM 85 EDTR EDT Reset Configuration 0 - 3 EDRSTCFG 2 Reset Ratio 0 - 10 RTIO 3 Reset Limit 0 - 20 ^F LIMT 10 EDT 4-20 ma Reset Input Enable/Disable EDTRSENS Disable HEAT Heating Control Type 0 - 4 HEATTYPE 0 Heating Supply Air Setpt 80-120 dF SASPHEAT 85 Occupied Heating Enabled Yes/No HTOCCENA No MBB Sensor Heat Relocate Yes/No HTLATMON No Staged Gas Heat Type 0 - 4 HTSTGTYP 0 Max Cap Change per Cycle 5 - 45 HTCAPMAX 45 S.Gas DB min.dF/PID Rate 0 - 5 HT_MR_DB 0.5 St.Gas Temp. Dead Band 0 - 5 ^F HT_SG_DB 2 Heat Rise dF/sec Clamp 0.05 - 0.2 HTSGRISE 0.06 LAT Limit Config 0 - 20 ^F HTLATLIM 10 Limit Switch Switch Monitoring? Yes/No HTLIMMON Yes Limit Switch High Temp 110 - 180 dF HT_LIMHI 170 Limit Switch Low Temp 100 - 170 dF HT_LIMLO 160 Heat Control Prop. Gain 0 - 1.5 HT_PGAIN 1 Heat Control Derv. Gain 0 - 1.5 HT_DGAIN 1 Heat PID Rate Config 60 - 300 sec HTSGPIDR 90 Hydronic Ctl.Prop. Gain 0 - 1.5 HW_PGAIN 1 Hydronic Ctl.Integ. Gain 0 - 1.5 HW_IGAIN 1 Hydronic Ctl.Derv. Gain 0 - 1.5 HW_DGAIN 1 Hydronic PID Rate Config 15 - 300 sec HOTWPIDR 90 Hydronic Ht.Serial Num.1 0 - 9999 HTCL_SN1 0 Hydronic Ht.Serial Num.2 0 - 6 HTCL_SN2 0 Hydronic Ht.Serial Num.3 0 - 9999 HTCL_SN3 0 Hydronic Ht.Serial Num.4 0 - 254 HTCL_SN4 0 Hydr.Ht.Ctl.Ang.Lo Limit 0-90 HTCLCALM 85 HUMD Humidifier Control Cfg. 0 - 4 HUMD_CFG 0 Humidifier Setpoint 0 - 100 % HUSP 40 Humidifier PID Run Rate 10 - 120 sec HUMDRATE 30 Humidifier Prop. Gain 0 - 5 HUMID_PG 1 Humidifier Integral Gain 0 - 5 HUMID_IG 0.3 Humidifier Deriv. Gain 0 - 5 HUMID_DG 0.3 Humd Serial Number 1 0 - 9999 HUMD_SN1 0 Humd Serial Number 2 0 - 6 HUMD_SN2 0 Humd Serial Number 3 0 - 9999 HUMD_SN3 0 Humd Serial Number 4 0 - 254 HUMD_SN4 0 Humd Ctrl Angle Lo Limit 0-90 HUMDCALM 85 183
Page 1 and 2:
Controls, Start-Up, Operation, Serv
Page 3 and 4:
WARNING What to do if you smell gas
Page 5 and 6:
and the ENTER keys until the desire
Page 7 and 8:
START-UP IMPORTANT: Do not attempt
Page 9 and 10:
Table 4 — Fan Performance — 48P
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
AIRFLOW (cfm) Table 10 — Fan Perf
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
AIRFLOW (Cfm) LEGEND Table 18 — F
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
AIRFLOW (cfm) LEGEND Bhp — Brake
Page 31 and 32:
HIGH-EFFICIENCY MOTORS Nominal Maxi
Page 33 and 34:
2. Under the Setpoints menu, set th
Page 35 and 36:
would use Period 2 and set days Sat
Page 37 and 38:
there is a loss of communication be
Page 39 and 40:
and when ON, the control sets a cap
Page 41 and 42:
System Mode Test — When the syste
Page 43 and 44:
Table 31 — Unit Configuration ITE
Page 45 and 46:
SETTING UP THE SYSTEM Machine Contr
Page 47 and 48:
High SST Alert Delay Time (H.SST)
Page 49 and 50:
Table 36 — Cool/Heat Set Point Of
Page 51 and 52:
Table 38 — Run Status Cool Displa
Page 53 and 54:
To use Demand Limiting, select the
Page 55 and 56:
Size 050, 055, 060 Contactor OFM(s)
Page 57 and 58:
Whenever the outdoor ambient temper
Page 59 and 60:
Demand Level Low Heat Off Offset (L
Page 61 and 62:
Limit Switch Low Temp (SW.L.T) —
Page 63 and 64:
STAGE Table 49 — IGC LED Indicato
Page 65 and 66:
Table 50 — Static Pressure Contro
Page 67 and 68:
Table 53 — Dirty Filter Switch Po
Page 69 and 70:
NOTE: If the user wishes to disable
Page 71 and 72:
the economizer modulates when attem
Page 73 and 74:
P = K * BP.P * (error) I = K * BP.I
Page 75 and 76:
its smoke. Closing the economizer (
Page 77 and 78:
Table 57 — Indoor Air Quality Con
Page 79 and 80:
Table 58 — Humidity Configuration
Page 81 and 82:
The default sensor is the return ai
Page 83 and 84:
TEMPERATURE COMPENSATED START LOGIC
Page 85 and 86:
Sensor Trim Configuration — The T
Page 87 and 88:
SUPPLY FAN VFD CONFIGURATION — Th
Page 89 and 90:
REMOTE SWITCH LOGIC CONFIGURATION (
Page 91 and 92:
Alarms and Alarm History for for an
Page 93 and 94:
Transducer Troubleshooting — The
Page 95 and 96:
Table 75 — 10K Thermistor vs Resi
Page 97 and 98:
TEMP RESISTANCE (F) (Ohms) -25 98,0
Page 99 and 100:
PRESSURE (PSIG) Table 80 — Suctio
Page 101 and 102:
Table 81 — Discharge Pressure Tra
Page 103 and 104:
Table 82 — Auto View of Run Statu
Page 105 and 106:
Table 84 — Cooling Information Di
Page 107 and 108:
equalize compressor oil levels. If
Page 109 and 110:
Table 91 — Alert and Alarm Codes
Page 111 and 112:
T072 (Evaporator Discharge Reset Se
Page 113 and 114:
This alarm will disable mechanical
Page 115 and 116:
This is the reverse of the Pressuri
Page 117 and 118:
117 a48-8408 Fig. 19 — Typical Po
Page 119 and 120:
OD ENTHALPY SWITCH LOW REMOTE OCCUP
Page 121 and 122:
Fig. 23 — Typical Electric Heat U
Page 123 and 124:
123 Fig. 25 — Typical Gas Heat Se
Page 125 and 126:
125 Fig. 27 — Component Arrangeme
Page 127 and 128:
ACCSY — Accessory ACC’Y — Acc
Page 129 and 130:
Table 93 — Rooftop Control Board
Page 131 and 132: Table 96 — Control Expansion Modu
Page 133 and 134: LEGEND IAQ — Indoor Air Quality V
Page 135 and 136: the motor position to be configured
Page 137 and 138: TIME EWT LWT SETP Run Status Servic
Page 139 and 140: Fig. 37 — Door Latch Fig. 38 —
Page 141 and 142: SUPPLY FAN AND POWER EXHAUST MOTOR
Page 143 and 144: Routine cleaning of coil surfaces i
Page 145 and 146: Saturated Discharge Temperature (de
Page 163 and 164: Gas System Adjustment (48P Only) GA
Page 165 and 166: APPENDIX A — LOCAL DISPLAY TABLES
Page 177 and 178: APPENDIX B — CCN TABLES (cont) ST
Page 179 and 180: APPENDIX B — CCN TABLES (cont) ST
Page 181: APPENDIX B — CCN TABLES (cont) SE
Page 185 and 186: APPENDIX B — CCN TABLES (cont) SE
Page 187 and 188: APPENDIX B — CCN TABLES (cont) MA
Page 189 and 190: APPENDIX B — CCN TABLES (cont) MA
Page 191 and 192: TESTACTC TESTCOOL TESTFANS TESTHEAT
Page 193 and 194: APPENDIX C — UNIT STAGING TABLES
Page 195 and 196: * 41 for Supply Fan Motor VFD, 42 f
Page 197 and 198: Fig. B — VFD Keypad START UP WITH
Page 199 and 200: Upload All Parameters — To upload
Page 201 and 202: To replace the main fan for frame s
Page 203 and 204: ALARM CODE ALARM NAME IN PANEL 2001
Page 205 and 206: APPENDIX E — MODE SELECTION PROCE
Page 207 and 208: CONTROLS SET POINT AND CONFIGURATIO
show all

Controls, Start-Up, Operation, Service and ... - Climayoreo

Create successful ePaper yourself

Delete template?

Save as template?