Controls, Start-Up, Operation, Service and ... - Climayoreo

More documents

Recommendations

Info

CONTROLS SET POINT AND CONFIGURATION LOG (cont) ITEM EXPANSION RANGE DEFAULT SETTING UNIT (cont) DS.AD Dig Scroll Adjust Delay 15 - 60 sec 20 DS.RP Dig Scroll Reduce Delta 0 - 100% 6 DS.RD Dig Scroll Reduce Delay 15 - 60 sec 30 DS.RO Dig Scroll Reduction OAT 70 - 120 dF 95 DS.MO Dig Scroll Max Only OAT 70 - 120 dF 105 MLV Min Load Valve Enable Enable/Disable Disable H.SST Hi SST Alert Delay Time 5 - 30 min 10 RR.VF Rev Rotation Verified ? Yes/No No CS.HP Use CSBs for HPS detect? Yes/No Yes EDT.R EVAP.DISCHRGE TEMP RESET RS.CF EDT Reset Configuration 0 - 3 (multi-text strings) 2 RTIO Reset Ratio 0 - 10 3 LIMT Reset Limit 0 - 20 ^F 10 RES.S EDT 4-20 ma Reset Input Enable/Disable Disable HEAT HEATING CONFIGURATION HT.CF Heating Control Type 0 - 4 0 HT.SP Heating Supply Air Setpt 80 - 120 dF 85 OC.EN Occupied Heating Enabled Yes/No No LAT.M MBB Sensor Heat Relocate Yes/No No SG.CF STAGED GAS CONFIGS SG.CFHT.ST Staged Gas Heat Type 0 - 4 0 SG.CFCAP.M Max Cap Change per Cycle 5 - 45 45 SG.CFM.R.DB S.Gas DB min.dF/PID Rate 0 - 5 0.5 SG.CFS.G.DB St.Gas Temp. Dead Band 0 - 5 ^F 2 SG.CFRISE Heat Rise dF/sec Clamp 0.05 - 0.2 0.06 SG.CFLAT.L LAT Limit Config 0 - 20 ^F 10 SG.CFLIM.M Limit Switch Monitoring? Yes/No Yes SG.CFSW.H.T Limit Switch High Temp 110 - 180 dF 170 SG.CFSW.L.T Limit Switch Low Temp 100 - 170 dF 160 SG.CFHT.P Heat Control Prop. Gain 0 - 1.5 1 SG.CFHT.D Heat Control Derv. Gain 0 - 1.5 1 SG.CFHT.TM Heat PID Rate Config 60 - 300 sec 90 HH.CF HYDRONIC HEAT CONFIGS HH.CFHW.P Hydronic Ctl.Prop. Gain 0 - 1.5 1 HH.CFHW.I Hydronic Ctl.Integ. Gain 0 - 1.5 1 HH.CFHW.D Hydronic Ctl.Derv. Gain 0 - 1.5 1 HH.CFHW.TM Hydronic PID Rate Config 15 - 300 sec 90 HH.CFACT.C HYDR.HEAT ACTUATOR CFGS. HH.CFACTCSN.1 Hydronic Ht.Serial Num.1 0 - 9999 0 HH.CFACTCSN.2 Hydronic Ht.Serial Num.2 0 - 6 0 HH.CFACTCSN.3 Hydronic Ht.Serial Num.3 0 - 9999 0 HH.CFACTCSN.4 Hydronic Ht.Serial Num.4 0 - 254 0 HH.CFACTCC.A.LM Hydr.Ht.Ctl.Ang.Lo Limit 0-90 85 SP SUPPLY STATIC PRESS.CFG. SP.CF Static Pressure Config Enable/Disable Disable SP.S Static Pressure Sensor Enable/Disable Disable SP.LO Static Press. Low Range -10 - 0 0 SP.HI Static Press. High Range 0 - 10 5 SP.SP Static Pressure Setpoint 0 - 5 1.5 SP.MN VFD Minimum Speed 0 - 100 20 SP.MX VFD Maximum Speed 0 - 100 100 SP.FS VFD Fire Speed Over. 0 - 100 100 SP.RS Stat. Pres. Reset Config 0 - 4 (multi-text strings) 0 SP.RT SP Reset Ratio 0.00 - 2.00 0.20 SP.LM SP Reset Limit 0.00 - 2.00 0.75 SP.EC SP Reset Econo Position 0 - 100% 5 S.PID STAT.PRESS.PID CONFIGS S.PIDSP.TM Stat.Pres.PID Run Rate 5 - 120 15 S.PIDSP.P Static Press. Prop. Gain 0 - 5 0.5 S.PIDSP.I Static Pressure Intg. Gain 0 - 2 0.5 S.PIDSP.D Static Pressure Derv. Gain 0 - 5 0.3 CL-2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE
CONTROLS SET POINT AND CONFIGURATION LOG (cont) ITEM EXPANSION RANGE DEFAULT SETTING ECON ECONOMIZER CONFIGURATION EC.EN Economizer Installed? Yes/No Yes EC2.E Econ.Act.2 Installed? Yes/No No EC.MN Economizer Min.Position 0 - 100% 5 EC.MX Economizer Max.Position 0 - 100% 98 E.TRM Economzr Trim For SumZ ? Yes/No Yes E.SEL Econ ChangeOver Select 0 - 3 (multi-text strings) 0 OA.E.C OA Enthalpy ChgOvr Selct 1 - 5 (multi-text strings) 4 OA.EN Outdr.Enth Compare Value 18 - 28 24 OAT.L High OAT Lockout Temp -40 - 120 dF 60 O.DEW OA Dewpoint Temp Limit 50 - 62 dF 55 ORH.S Outside Air RH Sensor Enable/Disable Disable CFM.C OUTDOOR AIR CFM CONTROL CFM.COCF.S Outdoor Air CFM Sensor Enable/Disable Disable CFM.CO.C.MX Economizer Min.Flow 0 - 20000 CFM 2000 CFM.CO.C.MN IAQ Demand Vent Min.Flow 0 - 20000 CFM 0 CFM.CO.C.DB Econ.Min.Flow Deadband 200 - 1000 CFM 400 E.CFG ECON.OPERATION CONFIGS E.CFGE.P.GN Economizer Prop.Gain 0.7 - 3.0 1 E.CFGE.RNG Economizer Range Adjust 0.5 - 5 ^F 2.5 E.CFGE.SPD Economizer Speed Adjust 0.1 - 10 0.75 E.CFGE.DBD Economizer Deadband 0.1 - 2 ^F 0.5 UEFC UNOCC.ECON.FREE COOLING UEFCFC.CF Unoc Econ Free Cool Cfg 0-2 (multi-text strings) 0 UEFCFC.TM Unoc Econ Free Cool Time 0 - 720 min 120 UEFCFC.L.O Un.Ec.Free Cool OAT Lock 40 - 70 dF 50 ACT.C ECON.ACTUATOR CONFIGS ACTCSN.1.1 Econ Serial Number 1 0 - 9999 0 ACTCSN.1.2 Econ Serial Number 2 0 - 6 0 ACTCSN.1.3 Econ Serial Number 3 0 - 9999 0 ACTCSN.1.4 Econ Serial Number 4 0 - 254 0 ACTCC.A.L1 Econ Ctrl Angle Lo Limit 0 - 90 85 ACTCSN.2.1 Econ 2 Serial Number 1 0 - 9999 0 ACTCSN.2.2 Econ 2 Serial Number 2 0 - 6 0 ACTCSN.2.3 Econ 2 Serial Number 3 0 - 9999 0 ACTCSN.2.4 Econ 2 Serial Number 4 0 - 254 0 ACTCC.A.L2 Econ 2 Ctrl Angle Lo Limit 0 - 90 85 BP BUILDING PRESS. CONFIGS BP.CF Building Press. Config 0 - 5 (multi-text strings) 0 BP.S Building Pressure Sensor Enable/Disable Disable BP.R Bldg. Press. (+/-) Range 0.10 - 0.25 "H2O 0.25 BP.SP Building Pressure Setp. -0.25 - 0.25 "H2O 0.05 BP.SO BP Setpoint Offset 0 - 0.5 "H2O 0.05 BP.P1 Power Exhaust On Setp.1 0 - 100% 25 BP.P2 Power Exhaust On Setp.2 0 - 100% 75 B.V.A VFD/ACTUATOR CONFIG B.V.ABP.FS VFD/Act. Fire Speed/Pos. 0 - 100% 100 B.V.ABP.MN VFD/Act. Min.Speed/Pos. 0 - 50% 0 B.V.ABP.MX VFD Maximum Speed 50 - 100% 100 B.V.ABP.1M BP 1 Actuator Max Pos. 85 - 100% 100 B.V.ABP.2M BP 2 Actuator Max Pos. 85 - 100% 100 B.V.ABP.CL BP Hi Cap VFD Clamp Val. 5 - 25% 10 CL-3
Page 1 and 2:
Controls, Start-Up, Operation, Serv
Page 3 and 4:
WARNING What to do if you smell gas
Page 5 and 6:
and the ENTER keys until the desire
Page 7 and 8:
START-UP IMPORTANT: Do not attempt
Page 9 and 10:
Table 4 — Fan Performance — 48P
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
AIRFLOW (cfm) Table 10 — Fan Perf
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
AIRFLOW (Cfm) LEGEND Table 18 — F
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
AIRFLOW (cfm) LEGEND Bhp — Brake
Page 31 and 32:
HIGH-EFFICIENCY MOTORS Nominal Maxi
Page 33 and 34:
2. Under the Setpoints menu, set th
Page 35 and 36:
would use Period 2 and set days Sat
Page 37 and 38:
there is a loss of communication be
Page 39 and 40:
and when ON, the control sets a cap
Page 41 and 42:
System Mode Test — When the syste
Page 43 and 44:
Table 31 — Unit Configuration ITE
Page 45 and 46:
SETTING UP THE SYSTEM Machine Contr
Page 47 and 48:
High SST Alert Delay Time (H.SST)
Page 49 and 50:
Table 36 — Cool/Heat Set Point Of
Page 51 and 52:
Table 38 — Run Status Cool Displa
Page 53 and 54:
To use Demand Limiting, select the
Page 55 and 56:
Size 050, 055, 060 Contactor OFM(s)
Page 57 and 58:
Whenever the outdoor ambient temper
Page 59 and 60:
Demand Level Low Heat Off Offset (L
Page 61 and 62:
Limit Switch Low Temp (SW.L.T) —
Page 63 and 64:
STAGE Table 49 — IGC LED Indicato
Page 65 and 66:
Table 50 — Static Pressure Contro
Page 67 and 68:
Table 53 — Dirty Filter Switch Po
Page 69 and 70:
NOTE: If the user wishes to disable
Page 71 and 72:
the economizer modulates when attem
Page 73 and 74:
P = K * BP.P * (error) I = K * BP.I
Page 75 and 76:
its smoke. Closing the economizer (
Page 77 and 78:
Table 57 — Indoor Air Quality Con
Page 79 and 80:
Table 58 — Humidity Configuration
Page 81 and 82:
The default sensor is the return ai
Page 83 and 84:
TEMPERATURE COMPENSATED START LOGIC
Page 85 and 86:
Sensor Trim Configuration — The T
Page 87 and 88:
SUPPLY FAN VFD CONFIGURATION — Th
Page 89 and 90:
REMOTE SWITCH LOGIC CONFIGURATION (
Page 91 and 92:
Alarms and Alarm History for for an
Page 93 and 94:
Transducer Troubleshooting — The
Page 95 and 96:
Table 75 — 10K Thermistor vs Resi
Page 97 and 98:
TEMP RESISTANCE (F) (Ohms) -25 98,0
Page 99 and 100:
PRESSURE (PSIG) Table 80 — Suctio
Page 101 and 102:
Table 81 — Discharge Pressure Tra
Page 103 and 104:
Table 82 — Auto View of Run Statu
Page 105 and 106:
Table 84 — Cooling Information Di
Page 107 and 108:
equalize compressor oil levels. If
Page 109 and 110:
Table 91 — Alert and Alarm Codes
Page 111 and 112:
T072 (Evaporator Discharge Reset Se
Page 113 and 114:
This alarm will disable mechanical
Page 115 and 116:
This is the reverse of the Pressuri
Page 117 and 118:
117 a48-8408 Fig. 19 — Typical Po
Page 119 and 120:
OD ENTHALPY SWITCH LOW REMOTE OCCUP
Page 121 and 122:
Fig. 23 — Typical Electric Heat U
Page 123 and 124:
123 Fig. 25 — Typical Gas Heat Se
Page 125 and 126:
125 Fig. 27 — Component Arrangeme
Page 127 and 128:
ACCSY — Accessory ACC’Y — Acc
Page 129 and 130:
Table 93 — Rooftop Control Board
Page 131 and 132:
Table 96 — Control Expansion Modu
Page 133 and 134:
LEGEND IAQ — Indoor Air Quality V
Page 135 and 136:
the motor position to be configured
Page 137 and 138:
TIME EWT LWT SETP Run Status Servic
Page 139 and 140:
Fig. 37 — Door Latch Fig. 38 —
Page 141 and 142:
SUPPLY FAN AND POWER EXHAUST MOTOR
Page 143 and 144:
Routine cleaning of coil surfaces i
Page 145 and 146:
Saturated Discharge Temperature (de
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158: Saturated Discharge Temperature (de
Page 163 and 164: Gas System Adjustment (48P Only) GA
Page 165 and 166: APPENDIX A — LOCAL DISPLAY TABLES
Page 177 and 178: APPENDIX B — CCN TABLES (cont) ST
Page 179 and 180: APPENDIX B — CCN TABLES (cont) ST
Page 181 and 182: APPENDIX B — CCN TABLES (cont) SE
Page 187 and 188: APPENDIX B — CCN TABLES (cont) MA
Page 189 and 190: APPENDIX B — CCN TABLES (cont) MA
Page 191 and 192: TESTACTC TESTCOOL TESTFANS TESTHEAT
Page 193 and 194: APPENDIX C — UNIT STAGING TABLES
Page 195 and 196: * 41 for Supply Fan Motor VFD, 42 f
Page 197 and 198: Fig. B — VFD Keypad START UP WITH
Page 199 and 200: Upload All Parameters — To upload
Page 201 and 202: To replace the main fan for frame s
Page 203 and 204: ALARM CODE ALARM NAME IN PANEL 2001
Page 205 and 206: APPENDIX E — MODE SELECTION PROCE
Page 207: CONTROLS SET POINT AND CONFIGURATIO
Page 211 and 212: CONTROLS SET POINT AND CONFIGURATIO
Page 213 and 214: CONTROLS SET POINT AND CONFIGURATIO
show all

Controls, Start-Up, Operation, Service and ... - Climayoreo

Create successful ePaper yourself

Delete template?

Save as template?