Controls, Start-Up, Operation, Service and ... - Climayoreo

More documents

Recommendations

Info

EDT Low Alert Limit/Occ (SA.L.O) — If the space temperature is below the configurable occupied evaporator discharge temperature (EDT) Low Alert Limit (SA.L.O), then Alert 302 will be generated and cooling operation will be stopped but heating operation will continue. The alert will automatically reset. EDT High Alert Limit/Occ (SA.H.O) — If the space temperature is above the configurable occupied EDT High Alert Limit (SA.H.O), then Alert 303 will be generated and heating operation will be stopped but cooling operation will continue. The alert will automatically reset. EDT Low Alert Limit/Unocc (SA.L.U) — If the space temperature is below the configurable unoccupied EDT Low Alert Limit (SA.L.U), then Alert 302 will be generated and cooling operation will be stopped but heating operation will continue. The alert will automatically reset. EDT High Alert Limit/Unocc (SA.H.U) — If the space temperature is above the configurable unoccupied EDT High Alert Limit (SA.H.U), then Alert 303 will be generated and heating operation will be stopped but cooling operation will continue. The alert will automatically reset. RAT Low Alert Limit/Occ (RA.L.O) — If the return-air temperature is below the configurable occupied RAT Low Alert Limit (RA.L.O), then Alert 304 will be generated and internal routines will be modified. Unit operation will continue but VAV heating operation will be disabled. The alert will automatically reset. RAT High Alert Limit/Occ (RA.H.O) — If the return-air temperature is above the configurable occupied RAT High Alert Limit (RA.H.O), then Alert 305 will be generated and operation will continue. The alert will automatically reset. RAT Low Alert Limit/Unocc (RA.L.U) — If the return-air temperature is below the configurable unoccupied RAT Low Alert Limit (RA.L.U), then Alert 304 will be generated. Unit operation will continue but VAV heating operation will be disabled. The alert will automatically reset. RAT High Alert Limit/Unocc (RA.H.U) — If the return-air temperature is above the configurable unoccupied RAT High Alert Limit (RA.H.U), then Alert 305 will be generated. Operation will continue. The alert will automatically reset. OAT Low Alert Limit (OAT.L) — If the outside-air temperature measured by the OAT thermistor is below the configurable OAT Low Alert Limit (OAT.L) then alert T316 will be generated. OAT High Alert Limit (OAT.H) — If the outside-air temperature measured by the OAT thermistor is above the configurable OAT High Alert Limit (OAT.H) then alert T317 will be generated. Table 61 — CCN Configuration 84 RARH Low Alert Limit (R.RH.L) — If the unit is configured to use a return air relative humidity sensor (ConfigurationUNITSENSRRH.S), and the measured level is below the configurable RH Low Alert Limit (R.RH.L), then Alert 308 will occur. The unit will continue to run and the alert will automatically reset. RARH High Alert Limit (R.RH.H) — If the unit is configured to use a return air relative humidity sensor (ConfigurationUNITSENSRRH.S), and the measured level is above the configurable RARH High Alert Limit (R.RH.H), then Alert 309 will occur. The unit will continue to run and the alert will automatically reset. OARH Low Alert Limit (O.RH.L) — If the unit is configured to use an outdoor air relative humidity sensor (ConfigurationECONORH.S) and the measured level is below the configurable OARH Low Alert Limit (O.RH.L), then economizer operation will be disabled. The unit will continue to run and the alert will automatically reset. OARH High Alert Limit (O.RH.H) — If the unit is configured to use a return air relative humidity sensor (ConfigurationECONORH.S) and the measured level is above the configurable OARH High Alert Limit (O.RH.H), then economizer operation will be disabled. The unit will continue to run and the alert will automatically reset. Supply Duct Pressure Low Alert Limit (SP.L) — If the unit is a VAV unit with a supply duct pressure sensor and the measured supply duct static pressure is below the configurable SP Low Alert Limit (DP.L), then Alert 310 will occur. The unit will continue to run and the alert will automatically reset. Supply Duct Pressure High Alert Limit (SP.H) — If the unit is a VAV unit with a supply duct pressure sensor and the measured supply duct static pressure is above the configurable SP High Alert Limit (SP.H), then Alert 311 will occur. The unit will continue to run and the alert will automatically reset. Building Pressure Low Alert Limit (BP.L) — If the unit is configured to use modulating power exhaust then a building static pressure limit can be configured using the BP Low Alert Limit (BP.L). If the measured pressure is below the limit then Alert 312 will occur. Building Pressure High Alert Limit (BP.H) — If the unit is configured to use modulating power exhaust then a building static pressure limit can be configured using the BP Hi Alert Limit (BP.H). If the measured pressure is above the limit, then Alert 313 will occur. Indoor Air Quality High Alert Limit (IAQ.H) — If the unit is configured to use a CO 2 sensor and the level is above the configurable IAQ High Alert Limit (IAQ.H) then the alert will occur. The unit will continue to run and the alert will automatically reset. ITEM EXPANSION RANGE UNITS CCN POINT DEFAULT CCN CCN CONFIGURATION CCNA CCN Address 1 - 239 CCNADD 1 CCNB CCN Bus Number 0 - 239 CCNBUS 0 BAUD CCN Baud Rate 1 - 5 CCNBAUDD 3 BROD CCN BROADCST DEFINITIONS TM.DT CCN Time/Date Broadcast ON/OFF CCNBC On OAT.B CCN OAT Broadcast ON/OFF OATBC Off ORH.B CCN OARH Broadcast ON/OFF OARHBC Off OAQ.B CCN OAQ Broadcast ON/OFF OAQBC Off G.S.B Global Schedule Broadcst ON/OFF GSBC Off B.ACK CCN Broadcast Ack'er ON/OFF CCNBCACK Off SC.OV CCN SCHEDULES-OVERRIDES SCH.N Schedule Number 0 - 99 SCHEDNUM 1 HOL.T Accept Global Holidays? YES/NO HOLIDAYT No O.T.L. Override Time Limit 0 - 4 HRS OTL 1 OV.EX Timed Override Hours 0 - 4 HRS OVR_EXT 0 SPT.O SPT Override Enabled ? YES/NO SPT_OVER Yes T58.O T58 Override Enabled ? YES/NO T58_OVER Yes GL.OV Global Sched. Override ? YES/NO GLBLOVER No
Sensor Trim Configuration — The TRIM submenu is used to calibrate the sensor trim settings. The trim settings are used when the actual measured reading does not match the sensor output. The sensor can be adjusted to match the actual measured reading with the trim function. A list is shown in Table 63. IMPORTANT: Sensor trim must not be used to extend unit operation past the allowable operating range. Doing so may impair or negatively affect the Carrier product warranty. Air Temperature Leaving Supply Fan Sensor (SAT.T) — This variable is used to adjust the supply fan temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. Return Air Temperature Sensor Trim (RAT.T) — This variable is used to adjust the return air temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. Outdoor Air Temperature Sensor Trim (OAT.T) — This variable is used to adjust the outdoor air temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. Space Temperature Sensor Trim (SPT.T) — This variable is used to adjust the space temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. Limit Switch Trim (L.SW.T) — This variable is used to adjust the limit switch temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. Table 62 — Alert Limit Configuration Table 63 — Sensor Trim Configuration 85 Air Temperature Leaving Evaporator Trim (CCT.T) — This variable is used to adjust the leaving evaporator temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. A1 Discharge Temperature (DTA.1) — This variable is used to adjust the A1 compressor discharge temperature sensor reading. The sensor reading can be adjusted ± 10° F to match the actual measured temperature. Suction Pressure Circuit A Trim (SP.A.T) — This variable is used to adjust the suction pressure sensor reading for circuit A. The sensor reading can be adjusted ± 50 psig to match the actual measured pressure. Suction Pressure Circuit B Trim (SP.B.T) — This variable is used to adjust the suction pressure sensor reading for circuit B. The sensor reading can be adjusted ± 50 psig to match the actual measured pressure. Discharge Pressure Circuit A Trim (DP.A.T) — This variable is used to adjust the discharge pressure sensor reading for circuit A. The sensor reading can be adjusted ± 50 psig to match the actual measured pressure. Discharge Pressure Circuit B Trim (DP.B.T) — This variable is used to adjust the discharge pressure sensor reading for circuit B. The sensor reading can be adjusted ±50 psig to match the actual measured pressure. 4 to 20 mA Inputs — There are a number of 4 to 20 mA inputs which may be calibrated. These inputs are located in Inputs4-20. They are: • SP.M.T — static pressure milliamp trim • BP.M.T — building pressure milliamp trim • OA.M.T — outside air cfm milliamp trim • RA.M.T — return air cfm milliamp trim • SA.M.T — supply air cfm milliamp trim ITEM EXPANSION RANGE UNITS CCN POINT DEFAULT SP.L.O SPT lo alert limit/occ -10-245 dF SPLO 60 SP.H.O SPT hi alert limit/occ -10-245 dF SPHO 85 SP.L.U SPT lo alert limit/unocc -10-245 dF SPLU 45 SP.H.U SPT hi alert limit/unocc -10-245 dF SPHU 100 SA.L.O EDT lo alert limit/occ -40-245 dF SALO 40 SA.H.O EDT hi alert limit/occ -40-245 dF SAHO 100 SA.L.U EDT lo alert limit/unocc -40-245 dF SALU 40 SA.H.U EDT hi alert limit/unocc -40-245 dF SAHU 100 RA.L.O RAT lo alert limit/occ -40-245 dF RALO 60 RA.H.O RAT hi alert limit/occ -40-245 dF RAHO 90 RA.L.U RAT lo alert limit/unocc -40-245 dF RALU 40 RA.H.U RAT hi alert limit/unocc -40-245 dF RAHU 100 OAT.L OAT lo alert limit -40-245 dF OATL -40 OAT.H OAT hi alert limit -40-245 dF OATH 150 R.RH.L RARH low alert limit 0-100 % RRHL 0 R.RH.H RARH high alert limit 0-100 % RRHH 100 O.RH.L OARH low alert limit 0-100 % ORHL 0 O.RH.H OARH high alert limit 0-100 % ORHH 100 SP.L SP low alert limit 0-5 "H2O SPL 0 SP.H SP high alert limit 0-5 "H2O SPH 2 BP.L BP lo alert limit -0.25-0.25 "H2O BPL -0.25 BP.H BP high alert limit -0.25-0.25 "H2O BPH 0.25 IAQ.H IAQ high alert limit 0-5000 IAQH 1200 ITEM EXPANSION RANGE UNITS CCN POINT DEFAULT TRIM SENSOR TRIM CONFIG. SAT.T Air Temp Lvg SF Trim -10 - 10 ^F SAT_TRIM 0 RAT.T RAT Trim -10 - 10 ^F RAT_TRIM 0 OAT.T OAT Trim -10 - 10 ^F OAT_TRIM 0 SPT.T SPT Trim -10 - 10 ^F SPT_TRIM 0 L.SW.T Limit Switch Trim -10 - 10 ^F LSW_TRIM 0 CCT.T Air Temp Lvg Evap Trim -10 - 10 ^F CCT_TRIM 0 DTA.1 A1 Discharge Temp Trim -10 - 10 ^F DTA1TRIM 0 SP.A.T Suct.Press.Circ.A Trim -50 - 50 PSIG SPA_TRIM 0 SP.B.T Suct.Press.Circ.B Trim -50 - 50 PSIG SPB_TRIM 0 DP.A.T Dis.Press.Circ.A Trim -50 - 50 PSIG DPA_TRIM 0 DP.B.T Dis.Press.Circ.B Trim -50 - 50 PSIG DPB_TRIM 0
Page 1 and 2:
Controls, Start-Up, Operation, Serv
Page 3 and 4:
WARNING What to do if you smell gas
Page 5 and 6:
and the ENTER keys until the desire
Page 7 and 8:
START-UP IMPORTANT: Do not attempt
Page 9 and 10:
Table 4 — Fan Performance — 48P
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
AIRFLOW (cfm) Table 10 — Fan Perf
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
AIRFLOW (Cfm) LEGEND Table 18 — F
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
AIRFLOW (cfm) LEGEND Bhp — Brake
Page 31 and 32:
HIGH-EFFICIENCY MOTORS Nominal Maxi
Page 33 and 34: 2. Under the Setpoints menu, set th
Page 35 and 36: would use Period 2 and set days Sat
Page 37 and 38: there is a loss of communication be
Page 39 and 40: and when ON, the control sets a cap
Page 41 and 42: System Mode Test — When the syste
Page 43 and 44: Table 31 — Unit Configuration ITE
Page 45 and 46: SETTING UP THE SYSTEM Machine Contr
Page 47 and 48: High SST Alert Delay Time (H.SST)
Page 49 and 50: Table 36 — Cool/Heat Set Point Of
Page 51 and 52: Table 38 — Run Status Cool Displa
Page 53 and 54: To use Demand Limiting, select the
Page 55 and 56: Size 050, 055, 060 Contactor OFM(s)
Page 57 and 58: Whenever the outdoor ambient temper
Page 59 and 60: Demand Level Low Heat Off Offset (L
Page 61 and 62: Limit Switch Low Temp (SW.L.T) —
Page 63 and 64: STAGE Table 49 — IGC LED Indicato
Page 65 and 66: Table 50 — Static Pressure Contro
Page 67 and 68: Table 53 — Dirty Filter Switch Po
Page 69 and 70: NOTE: If the user wishes to disable
Page 71 and 72: the economizer modulates when attem
Page 73 and 74: P = K * BP.P * (error) I = K * BP.I
Page 75 and 76: its smoke. Closing the economizer (
Page 77 and 78: Table 57 — Indoor Air Quality Con
Page 79 and 80: Table 58 — Humidity Configuration
Page 81 and 82: The default sensor is the return ai
Page 83: TEMPERATURE COMPENSATED START LOGIC
Page 87 and 88: SUPPLY FAN VFD CONFIGURATION — Th
Page 89 and 90: REMOTE SWITCH LOGIC CONFIGURATION (
Page 91 and 92: Alarms and Alarm History for for an
Page 93 and 94: Transducer Troubleshooting — The
Page 95 and 96: Table 75 — 10K Thermistor vs Resi
Page 97 and 98: TEMP RESISTANCE (F) (Ohms) -25 98,0
Page 99 and 100: PRESSURE (PSIG) Table 80 — Suctio
Page 101 and 102: Table 81 — Discharge Pressure Tra
Page 103 and 104: Table 82 — Auto View of Run Statu
Page 105 and 106: Table 84 — Cooling Information Di
Page 107 and 108: equalize compressor oil levels. If
Page 109 and 110: Table 91 — Alert and Alarm Codes
Page 111 and 112: T072 (Evaporator Discharge Reset Se
Page 113 and 114: This alarm will disable mechanical
Page 115 and 116: This is the reverse of the Pressuri
Page 117 and 118: 117 a48-8408 Fig. 19 — Typical Po
Page 119 and 120: OD ENTHALPY SWITCH LOW REMOTE OCCUP
Page 121 and 122: Fig. 23 — Typical Electric Heat U
Page 123 and 124: 123 Fig. 25 — Typical Gas Heat Se
Page 125 and 126: 125 Fig. 27 — Component Arrangeme
Page 127 and 128: ACCSY — Accessory ACC’Y — Acc
Page 129 and 130: Table 93 — Rooftop Control Board
Page 131 and 132: Table 96 — Control Expansion Modu
Page 133 and 134: LEGEND IAQ — Indoor Air Quality V
Page 135 and 136:
the motor position to be configured
Page 137 and 138:
TIME EWT LWT SETP Run Status Servic
Page 139 and 140:
Fig. 37 — Door Latch Fig. 38 —
Page 141 and 142:
SUPPLY FAN AND POWER EXHAUST MOTOR
Page 143 and 144:
Routine cleaning of coil surfaces i
Page 145 and 146:
Saturated Discharge Temperature (de
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Gas System Adjustment (48P Only) GA
Page 165 and 166:
APPENDIX A — LOCAL DISPLAY TABLES
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
APPENDIX B — CCN TABLES (cont) ST
Page 179 and 180:
APPENDIX B — CCN TABLES (cont) ST
Page 181 and 182:
APPENDIX B — CCN TABLES (cont) SE
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
APPENDIX B — CCN TABLES (cont) MA
Page 189 and 190:
APPENDIX B — CCN TABLES (cont) MA
Page 191 and 192:
TESTACTC TESTCOOL TESTFANS TESTHEAT
Page 193 and 194:
APPENDIX C — UNIT STAGING TABLES
Page 195 and 196:
* 41 for Supply Fan Motor VFD, 42 f
Page 197 and 198:
Fig. B — VFD Keypad START UP WITH
Page 199 and 200:
Upload All Parameters — To upload
Page 201 and 202:
To replace the main fan for frame s
Page 203 and 204:
ALARM CODE ALARM NAME IN PANEL 2001
Page 205 and 206:
APPENDIX E — MODE SELECTION PROCE
Page 207 and 208:
CONTROLS SET POINT AND CONFIGURATIO
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
show all

Controls, Start-Up, Operation, Service and ... - Climayoreo

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?