Controls, Start-Up, Operation, Service and ... - Climayoreo

More documents

Recommendations

Info

TEMP (C) Table 76 — 10K Thermistor vs Resistance (T55, T56, OAT, RAT, EDT, LAT Sensor) (C) TEMP RESISTANCE (C) (Ohms) –32 200,510 –31 188,340 –30 177,000 –29 166,342 –28 156,404 –27 147,134 –26 138,482 –25 130,402 –24 122,807 –23 115,710 –22 109,075 –21 102,868 –20 97,060 –19 91,588 –18 86,463 –17 81,662 –16 77,162 –15 72,940 –14 68,957 –13 65,219 –12 61,711 –11 58,415 –10 55,319 –9 52,392 –8 49,640 –7 47,052 –6 44,617 –5 42,324 –4 40,153 –3 38,109 –2 36,182 –1 34,367 0 32,654 1 31,030 2 29,498 3 28,052 4 26,686 5 25,396 6 24,171 7 23,013 8 21,918 9 20,883 10 19,903 11 18,972 12 18,090 13 17,255 14 16,474 TEMP (F) TEMP RESISTANCE (C) (Ohms) 15 15,714 16 15,000 17 14,323 18 13,681 19 13,071 20 12,493 21 11,942 22 11,418 23 10,921 24 10,449 25 10,000 26 9,571 27 9,164 28 8,776 29 8,407 30 8,056 31 7,720 32 7,401 33 7,096 34 6,806 35 6,530 36 6,266 37 6,014 38 5,774 39 5,546 40 5,327 41 5,117 42 4,918 43 4,727 44 4,544 45 4,370 46 4,203 47 4,042 48 3,889 49 3,743 50 3,603 51 3,469 52 3,340 53 3,217 54 3,099 55 2,986 56 2,878 57 2,774 58 2,675 59 2,579 60 2,488 61 2,400 Table 77 — 86K Thermistor vs Resistance (DTA1) RESISTANCE (Ohms) -40 -40 2,889,600 -35 -31 2,087,220 -30 -22 1,522,200 -25 -13 1,121,440 -20 -4 834,720 -15 5 627,280 -10 14 475,740 -5 23 363,990 0 32 280,820 5 41 218,410 10 50 171,170 15 59 135,140 20 68 107,440 25 77 86,000 30 86 69,280 35 95 56,160 40 104 45,810 45 113 37,580 50 122 30,990 55 131 25,680 60 140 21,400 70 158 15,070 96 TEMP (C) TEMP RESISTANCE (C) (Ohms) 62 2,315 63 2,235 64 2,157 65 2,083 66 2,011 67 1,943 68 1,876 69 1,813 70 1,752 71 1,693 72 1,637 73 1,582 74 1,530 75 1,480 76 1,431 77 1,385 78 1,340 79 1,297 80 1,255 81 1,215 82 1,177 83 1,140 84 1,104 85 1,070 86 1,037 87 1,005 88 974 89 944 90 915 91 889 92 861 93 836 94 811 95 787 96 764 97 742 98 721 99 700 100 680 101 661 102 643 103 626 104 609 105 592 106 576 107 561 TEMP (F) RESISTANCE (Ohms) 75 167 12,730 80 176 10,790 85 185 9,200 90 194 7,870 95 203 6,770 100 212 5,850 105 221 5,090 110 230 4,450 115 239 3,870 120 248 3,350 125 257 2,920 130 266 2,580 135 275 2,280 140 284 2,020 145 293 1,800 150 302 1,590 155 311 1,390 160 320 1,250 165 329 1,120 170 338 1,010 175 347 920 180 356 830
TEMP RESISTANCE (F) (Ohms) –25 98,010 –24 94,707 –23 91,522 –22 88,449 –21 85,486 –20 82,627 –19 79,871 –18 77,212 –17 74,648 –16 72,175 –15 69,790 –14 67,490 –13 65,272 –12 63,133 –11 61,070 –10 59,081 –9 57,162 –8 55,311 –7 53,526 –6 51,804 –5 50,143 –4 48,541 –3 46,996 –2 45,505 –1 44,066 0 42,679 1 41,339 2 40,047 3 38,800 4 37,596 5 36,435 6 35,313 7 34,231 8 33,185 9 32,176 10 31,202 11 30,260 12 29,351 13 28,473 14 27,624 15 26,804 16 26,011 17 25,245 18 24,505 19 23,789 20 23,096 21 22,427 22 21,779 23 21,153 24 20,547 25 19,960 26 19,393 27 18,843 28 18,311 29 17,796 30 17,297 31 16,814 32 16,346 33 15,892 34 15,453 35 15,027 36 14,614 37 14,214 38 13,826 39 13,449 40 13,084 41 12,730 42 12,387 43 12,053 44 11,730 45 11,416 46 11,112 47 10,816 48 10,529 49 10,250 50 9,979 51 9,717 52 9,461 53 9,213 54 8,973 55 8,739 56 8,511 57 8,291 58 8,076 Table 78 — 5K Thermistor vs. Resistance (RTA1) (F) TEMP RESISTANCE (F) (Ohms) 59 7,686 60 7,665 61 7,468 62 7,277 63 7,091 64 6,911 65 6,735 66 6,564 67 6,399 68 6,238 69 6,081 70 5,929 71 5,781 72 5,637 73 5,497 74 5,361 75 5,229 76 5,101 77 4,976 78 4,855 79 4,737 80 4,622 81 4,511 82 4,403 83 4,298 84 4,196 85 4,096 86 4,000 87 3,906 88 3,814 89 3,726 90 3,640 91 3,556 92 3,474 93 3,395 94 3,318 95 3,243 96 3,170 97 3,099 98 3,031 99 2,964 100 2,898 101 2,835 102 2,773 103 2,713 104 2,655 105 2,597 106 2,542 107 2,488 108 2,436 109 2,385 110 2,335 111 2,286 112 2,239 113 2,192 114 2,147 115 2,103 116 2,060 117 2,018 118 1,977 119 1,937 120 1,898 121 1,860 122 1,822 123 1,786 124 1,750 125 1,715 126 1,680 127 1,647 128 1,614 129 1,582 130 1,550 131 1,519 132 1,489 133 1,459 134 1,430 135 1,401 136 1,373 137 1,345 138 1,318 139 1,291 140 1,265 141 1,240 142 1,214 97 TEMP RESISTANCE (F) (Ohms) 143 1,190 144 1,165 145 1,141 146 1,118 147 1,095 148 1,072 149 1,050 150 1,029 151 1,007 152 986 153 965 154 945 155 925 156 906 157 887 158 868 159 850 160 832 161 815 162 798 163 782 164 765 165 750 166 734 167 719 168 705 169 690 170 677 171 663 172 650 173 638 174 626 175 614 176 602 177 591 178 581 179 570 180 561 181 551 182 542 183 533 184 524 185 516 186 508 187 501 188 494 189 487 190 480 191 473 192 467 193 461 194 456 195 450 196 445 197 439 198 434 199 429 200 424 201 419 202 415 203 410 204 405 205 401 206 396 207 391 208 386 209 382 210 377 211 372 212 367 213 361 214 356 215 350 216 344 217 338 218 332 219 325 220 318 221 311 222 304 223 297 224 289 225 282
Page 1 and 2:
Controls, Start-Up, Operation, Serv
Page 3 and 4:
WARNING What to do if you smell gas
Page 5 and 6:
and the ENTER keys until the desire
Page 7 and 8:
START-UP IMPORTANT: Do not attempt
Page 9 and 10:
Table 4 — Fan Performance — 48P
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
AIRFLOW (cfm) Table 10 — Fan Perf
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
AIRFLOW (Cfm) LEGEND Table 18 — F
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
AIRFLOW (cfm) LEGEND Bhp — Brake
Page 31 and 32:
HIGH-EFFICIENCY MOTORS Nominal Maxi
Page 33 and 34:
2. Under the Setpoints menu, set th
Page 35 and 36:
would use Period 2 and set days Sat
Page 37 and 38:
there is a loss of communication be
Page 39 and 40:
and when ON, the control sets a cap
Page 41 and 42:
System Mode Test — When the syste
Page 43 and 44:
Table 31 — Unit Configuration ITE
Page 45 and 46: SETTING UP THE SYSTEM Machine Contr
Page 47 and 48: High SST Alert Delay Time (H.SST)
Page 49 and 50: Table 36 — Cool/Heat Set Point Of
Page 51 and 52: Table 38 — Run Status Cool Displa
Page 53 and 54: To use Demand Limiting, select the
Page 55 and 56: Size 050, 055, 060 Contactor OFM(s)
Page 57 and 58: Whenever the outdoor ambient temper
Page 59 and 60: Demand Level Low Heat Off Offset (L
Page 61 and 62: Limit Switch Low Temp (SW.L.T) —
Page 63 and 64: STAGE Table 49 — IGC LED Indicato
Page 65 and 66: Table 50 — Static Pressure Contro
Page 67 and 68: Table 53 — Dirty Filter Switch Po
Page 69 and 70: NOTE: If the user wishes to disable
Page 71 and 72: the economizer modulates when attem
Page 73 and 74: P = K * BP.P * (error) I = K * BP.I
Page 75 and 76: its smoke. Closing the economizer (
Page 77 and 78: Table 57 — Indoor Air Quality Con
Page 79 and 80: Table 58 — Humidity Configuration
Page 81 and 82: The default sensor is the return ai
Page 83 and 84: TEMPERATURE COMPENSATED START LOGIC
Page 85 and 86: Sensor Trim Configuration — The T
Page 87 and 88: SUPPLY FAN VFD CONFIGURATION — Th
Page 89 and 90: REMOTE SWITCH LOGIC CONFIGURATION (
Page 91 and 92: Alarms and Alarm History for for an
Page 93 and 94: Transducer Troubleshooting — The
Page 95: Table 75 — 10K Thermistor vs Resi
Page 99 and 100: PRESSURE (PSIG) Table 80 — Suctio
Page 101 and 102: Table 81 — Discharge Pressure Tra
Page 103 and 104: Table 82 — Auto View of Run Statu
Page 105 and 106: Table 84 — Cooling Information Di
Page 107 and 108: equalize compressor oil levels. If
Page 109 and 110: Table 91 — Alert and Alarm Codes
Page 111 and 112: T072 (Evaporator Discharge Reset Se
Page 113 and 114: This alarm will disable mechanical
Page 115 and 116: This is the reverse of the Pressuri
Page 117 and 118: 117 a48-8408 Fig. 19 — Typical Po
Page 119 and 120: OD ENTHALPY SWITCH LOW REMOTE OCCUP
Page 121 and 122: Fig. 23 — Typical Electric Heat U
Page 123 and 124: 123 Fig. 25 — Typical Gas Heat Se
Page 125 and 126: 125 Fig. 27 — Component Arrangeme
Page 127 and 128: ACCSY — Accessory ACC’Y — Acc
Page 129 and 130: Table 93 — Rooftop Control Board
Page 131 and 132: Table 96 — Control Expansion Modu
Page 133 and 134: LEGEND IAQ — Indoor Air Quality V
Page 135 and 136: the motor position to be configured
Page 137 and 138: TIME EWT LWT SETP Run Status Servic
Page 139 and 140: Fig. 37 — Door Latch Fig. 38 —
Page 141 and 142: SUPPLY FAN AND POWER EXHAUST MOTOR
Page 143 and 144: Routine cleaning of coil surfaces i
Page 145 and 146: Saturated Discharge Temperature (de
Page 147 and 148:
Saturated Discharge Temperature (de
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Gas System Adjustment (48P Only) GA
Page 165 and 166:
APPENDIX A — LOCAL DISPLAY TABLES
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
APPENDIX B — CCN TABLES (cont) ST
Page 179 and 180:
APPENDIX B — CCN TABLES (cont) ST
Page 181 and 182:
APPENDIX B — CCN TABLES (cont) SE
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
APPENDIX B — CCN TABLES (cont) MA
Page 189 and 190:
APPENDIX B — CCN TABLES (cont) MA
Page 191 and 192:
TESTACTC TESTCOOL TESTFANS TESTHEAT
Page 193 and 194:
APPENDIX C — UNIT STAGING TABLES
Page 195 and 196:
* 41 for Supply Fan Motor VFD, 42 f
Page 197 and 198:
Fig. B — VFD Keypad START UP WITH
Page 199 and 200:
Upload All Parameters — To upload
Page 201 and 202:
To replace the main fan for frame s
Page 203 and 204:
ALARM CODE ALARM NAME IN PANEL 2001
Page 205 and 206:
APPENDIX E — MODE SELECTION PROCE
Page 207 and 208:
CONTROLS SET POINT AND CONFIGURATIO
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
show all

Controls, Start-Up, Operation, Service and ... - Climayoreo

Create successful ePaper yourself

Delete template?

Save as template?