Specifications - Lord and Son Construction, Inc.

More documents

Recommendations

Info

Asbestos Abatement and Management Inspection Report Bldg _________ Start Date____________ Completion Date_________ Required Asbestos Abatement and Mgt Procedures Pre - Job 10 Day Notification and return acknowledgment from MDEQ Asbestos Hazard Abatement Plan (to be certified by a Certified Industrial Hygienist, Management Planner, or Project Designer) Asbestos Work Plan (scope of work, removal procedures, worker protection, air monitoring, disposal location, containment procedures) MDEQ Asbestos Abatement Certification for the Company Supervisor’s qualifications and MDEQ Certification CURRENT MDEQ State Certifications (applications will not be accepted) for all individuals working on the site Certificates of Worker Release for all individuals Physicals and respiratory fit test for all individuals Required Asbestos Abatement and Mgt Procedures During Work Containment area, negative air machine, and critical barriers in place and approved by CSC/CEV Asbestos POC Received/ Approved Complete Comments LEC/MSD Form #3 – 1/30/07
Containment area and critical barriers secure Workers wearing personal protective equipment (PPE) Asbestos-containing material bagged appropriately Air monitoring conducted on workers Air monitoring conducted outside abatement area Daily log review (assurance of no uncertified individuals performing abatement work) Asbestos Abatement and Management Procedures Post - Job Asbestos POC and Bioenvironmental (when required) walk-though and approval of completed abatement & area cleaned of asbestos fibers (cleaning procedures in Asbestos Management and Operations Plan) Air sampling results submitted for approval by asbestos POC prior to removal of containment area and critical barriers Asbestos waste handled and disposed of in accordance with State law – asbestos POC must review waste prior to leaving Air Sampling Results Daily Report Logs Daily Worker Sign-In/Out Sheets Waste manifest (must be signed by KAFB personnel) Complete LEC/MSD Form #3 – 1/30/07
Page 1 and 2:
FINAL DESIGN SUBMITTAL FOR: RENOVAT
Page 3 and 4:
Division 9 - Finishes Section 09 22
Page 5 and 6:
SECTION 00102 LIST OF DRAWINGS PART
Page 7 and 8:
SECTION 00103 SUMMARY OF PROJECT WO
Page 9 and 10:
SECTION 01000 GENERAL REQUIREMENTS
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
SECTION 01001 HVAC COORDINATION COM
Page 19 and 20:
SECTION 01001 HVAC COORDINATION COM
Page 21 and 22:
SECTION 01140 WORK RESTRICTIONS PAR
Page 23 and 24:
SECTION 01150 QUALITY REQUIREMENTS
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
SECTION 01330 SUBMITTAL PROCEDURES
Page 33 and 34:
SECTION 01330A PROJECT SCHEDULE PAR
Page 35 and 36: SECTION 01330A PROJECT SCHEDULE 3.6
Page 37 and 38: SECTION 01355A ENVIRONMENTAL PROTEC
Page 39 and 40: PART 2 PRODUCTS (NOT USED) SECTION
Page 41 and 42: SECTION 01500 TEMPORARY CONSTRUCTIO
Page 47 and 48: SECTION 01732 Selective demolition
Page 49 and 50: SECTION 01732 Selective demolition
Page 51 and 52: SECTION 01770N CLOSEOUT PROCEDURES
Page 53 and 54: SECTION 01779 TESTING AND ACCEPTANC
Page 55 and 56: SECTION 01780A CLOSEOUT SUBMITTALS
Page 57 and 58: SECTION 01780A CLOSEOUT SUBMITTALS
Page 59 and 60: SECTION 01782 OPERATION AND MAINTEN
Page 61 and 62: SECTION 01782 OPERATION AND MAINTEN
Page 63 and 64: SECTION 02000 GENERAL DEMOLITION Pr
Page 65 and 66: SECTION 02000 GENERAL DEMOLITION B.
Page 67 and 68: SECTION 02000 GENERAL DEMOLITION no
Page 69 and 70: fibers. Filters should be of 99.97%
Page 71 and 72: with 40 CFR 61, B., 61.22, d.; shal
Page 73 and 74: PART 2 - PRODUCTS 2.1 GENERAL A. De
Page 75 and 76: 7. Maintain emergency and fire exit
Page 77 and 78: . Do not shut down negative air sys
Page 79 and 80: 3.5 SECOND CLEANING - GENERAL A. Se
Page 81 and 82: Thereafter, during the removal proc
Page 83 and 84: E. Phase Contrast Microscopy: (for
Page 85: Once the submittals are approved in
Page 89 and 90: Client: Log-In: Eley Guild Hardy Ar
Page 99 and 100: 1.5 PROJECT CONDITIONS A. Governmen
Page 101 and 102: 3.3 PREPARATION c. Tubes shall be r
Page 103 and 104: SECTION 04 20 00 - UNIT MASONRY PAR
Page 105 and 106: with expansion anchors. C. Air Infi
Page 107 and 108: SECTION 06 10 00 - ROUGH CARPENTRY
Page 109 and 110: 2.2 ACCESSORIES 3. General Plywood
Page 111 and 112: C. Installation of Plywood: 1. Gene
Page 113 and 114: 2.2 MATERIALS A. General: Solid pol
Page 115 and 116: 1/4 inch thick sheet product. Panel
Page 117 and 118: SECTION 07 21 00 - THERMAL INSULATI
Page 119 and 120: . Install batts at all cracks aroun
Page 121 and 122: 2.2 MATERIALS B. Georgia Pacific Co
Page 123 and 124: SECTION 07 52 16 - MODIFIED BITUMIN
Page 125 and 126: D. Review in Depth: Project Manual,
Page 127 and 128: Documents. C. Roofing Manufacturer
Page 129 and 130: . “Dens-Deck”; Georgia Pacific
Page 131 and 132: . PolyFleece is 100% polyester, 2.4
Page 133 and 134: 2. Provide at ALL roof curbs in lie
Page 135 and 136: A. Install pipestands and other sup
Page 137 and 138:
SECTION 07 92 00 - JOINT SEALANTS P
Page 139 and 140:
PART 3 - EXECUTION 3.1 PRECONSTRUCT
Page 141 and 142:
SECTION 08 11 13 - HOLLOW METAL DOO
Page 143 and 144:
3. Close top and bottom edges as in
Page 145 and 146:
3.3 ADJUSTING B. Placing Frames 1.
Page 147 and 148:
1.3 QUALITY ASSURANCE A. General: C
Page 149 and 150:
F. Pair and Set Match: Provide for
Page 151 and 152:
1. Clearances: Provide 1/8 inch at
Page 153 and 154:
1.4 WARRANTY A. Provide manufacture
Page 155 and 156:
SECTION 08 34 59 - VAULT DOORS PART
Page 157 and 158:
SECTION 08 71 00 - DOOR HARDWARE PA
Page 159 and 160:
D. Templates for doors, frames, and
Page 161 and 162:
c. Metals: Construct lock cylinder
Page 163 and 164:
e. All surface closers shall be cer
Page 165 and 166:
B. Base Metals: Produce hardware un
Page 167 and 168:
C. Door Hardware Supplier's Field S
Page 169 and 170:
with significant edge damage or oth
Page 171 and 172:
B. Glazing 3.3 CLEANING 3.4 PROTECT
Page 173 and 174:
2. Protective Coating: ASTM A 653/A
Page 175 and 176:
PART 3 - EXECUTION 3.1 INSTALLATION
Page 177 and 178:
SECTION 09 29 00 - GYPSUM BOARD PAR
Page 179 and 180:
2.2 MATERIALS A. Mold and Mildew Re
Page 181 and 182:
3.3 INSTALLATION A. General: 1. Ins
Page 183 and 184:
2. Control Joints: a. Install contr
Page 185 and 186:
SECTION 09 30 00 - TILING PART 1 -
Page 187 and 188:
B. General: 1. Color as indicated o
Page 189 and 190:
3.3 PROTECTION fixtures from effect
Page 191 and 192:
C. Handle acoustical ceiling units
Page 193 and 194:
3.3 INSTALLATION 3.4 CLEANING A. Ge
Page 195 and 196:
2. ASTM E 662 (Smoke Generation) Ma
Page 197 and 198:
material and a flush or “tapered
Page 199 and 200:
3.4 CLEANING 2. Lay tile from cente
Page 201 and 202:
SECTION 09 68 00 - CARPETING PART 1
Page 203 and 204:
B. Carpet Edge Guard: 1. Extruded o
Page 205 and 206:
SECTION 09 90 00 - PAINTING AND COA
Page 207 and 208:
3. Thinning instructions 4. Applica
Page 209 and 210:
PART 3 - EXECUTION 3.1 EXAMINATION
Page 211 and 212:
3.4 CLEANING 2. Mechanical items to
Page 213 and 214:
SECTION 09 97 23 - CONCRETE AND MAS
Page 215 and 216:
3.2 APPLICATION C. Do not apply the
Page 217 and 218:
PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 219 and 220:
3.2 CLEANING A. Upon completion all
Page 221 and 222:
PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 223 and 224:
G. Stile Shoe shall be one-piece, 4
Page 225 and 226:
SECTION 10 28 00 - TOILET AND BATH
Page 227 and 228:
B. Toilet Accessory Schedule Symbol
Page 229 and 230:
B. Toilet Accessory Schedule Symbol
Page 231 and 232:
SECTION 10 44 13 - FIRE EXTINGUISHE
Page 233 and 234:
SECTION 10 51 13 - METAL LOCKERS PA
Page 235 and 236:
2.) Provide necessary end closures.
Page 237 and 238:
Officer of unsatisfactory preparati
Page 239 and 240:
ASTM A 47/A 47M ASTM A 53/A 53M AST
Page 241 and 242:
Uniformly space sprinklers on branc
Page 243 and 244:
Three copies of the completed Final
Page 245 and 246:
Submit spare parts data for each di
Page 247 and 248:
2.5.3 Corrosion Resistant Sprinkler
Page 249 and 250:
manufacturer's listed range and sha
Page 251 and 252:
and booster pump) into the system a
Page 253 and 254:
The Fire Protection Specialist and
Page 255 and 256:
AWWA C652 (2002) Disinfection of Wa
Page 257 and 258:
ASTM A 516/A 516M ASTM A 518/A 518M
Page 259 and 260:
ASTM D 2466 ASTM D 2467 ASTM D 2564
Page 261 and 262:
ASTM F 442/F 442M ASTM F 477 ASTM F
Page 263 and 264:
NEMA 250 NEMA MG 1 NEMA MG 11 (2008
Page 265 and 266:
Plastic shower stalls Pumps; G Show
Page 267 and 268:
publications to the "authority havi
Page 269 and 270:
spaces below kitchen floors. Plasti
Page 271 and 272:
h. Coal-Tar Protective Coatings and
Page 273 and 274:
2.4 FIXTURES Fixtures shall be wate
Page 275 and 276:
floor or wall outlet copper alloy b
Page 277 and 278:
flashing or waterproofing membrane
Page 279 and 280:
* *2.8.2 Phenolic Resin Coatings fo
Page 281 and 282:
concrete may be provided in lieu of
Page 283 and 284:
inch brass plugs or caps shall be p
Page 285 and 286:
vernier or dial caliper, narrow-lan
Page 287 and 288:
Sleeves in nonbearing walls or ceil
Page 289 and 290:
a. Types 5, 12, and 26 shall not be
Page 291 and 292:
or one or two 1/8 bends extended to
Page 293 and 294:
carrier type. The carrier shall pro
Page 295 and 296:
joining of the surfaces by roller o
Page 297 and 298:
Painting of pipes, hangers, support
Page 299 and 300:
3.8.2 Defective Work If inspection
Page 301 and 302:
Take addition samples of water in d
Page 303 and 304:
ASTM A 47/A 47M for use with Item 5
Page 305 and 306:
5 Seamless red brass pipe, X X X AS
Page 307 and 308:
socket-welding and threaded, MSS SP
Page 309 and 310:
SECTION 22 07 19 PLUMBING PIPING IN
Page 311 and 312:
ASTM E 84 . Provide coatings and se
Page 313 and 314:
Pipe barrel insulation shall be Typ
Page 315 and 316:
Conform to ASTM C 1136 for, Type I,
Page 317 and 318:
In lieu of materials and methods pr
Page 319 and 320:
For other fittings and valves, cut
Page 321 and 322:
with a bedding mix and wrap with ga
Page 323 and 324:
ASTM B 766 ASTM C 553 ASTM D 1654 A
Page 325 and 326:
Fan Coil Unit Number FC - Identify
Page 327 and 328:
. Where materials or equipment are
Page 329 and 330:
Provide components and equipment th
Page 331 and 332:
c. Provide sealants that conform to
Page 333 and 334:
Furnish all air deflectors, except
Page 335 and 336:
2.10.5 Insulation The requirements
Page 337 and 338:
3.2.8 Duct Test Holes Provide holes
Page 339 and 340:
. Temperatures between 120 and 400
Page 341 and 342:
SECTION 23 03 00.00 20 BASIC MECHAN
Page 343 and 344:
the Contracting Officer as authoriz
Page 345 and 346:
PART 3 EXECUTION 3.1 PAINTING OF NE
Page 347 and 348:
SECTION 23 05 48 VIBRATION CONTROLS
Page 349 and 350:
within this section. Include in tes
Page 351 and 352:
mounted through 5 hp None C-CIB-1.0
Page 353 and 354:
2.3 PIPE AND DUCT VIBRATION ISOLATI
Page 355 and 356:
SECTION 23 05 93 TESTING, ADJUSTING
Page 357 and 358:
In some instances, terminology diff
Page 359 and 360:
furnishing equipment, or constructi
Page 361 and 362:
main ducts, branch main ducts, bran
Page 363 and 364:
paragraph 3.5.7, "Actual Capacity V
Page 365 and 366:
Comply with paragraph entitled "Sou
Page 367 and 368:
3.4.11.3 Prerequisite for Approval
Page 369 and 370:
ASTM C 1427 ASTM C 195 ASTM C 449 A
Page 371 and 372:
1.2.1 General Provide field-applied
Page 373 and 374:
Materials shall be delivered in the
Page 375 and 376:
Aluminum jackets shall be corrugate
Page 377 and 378:
2.2.12 Insulation Bands Insulation
Page 379 and 380:
2.4.1.2 Blanket Insulation Blanket
Page 381 and 382:
3.1.5 Welding No welding shall be d
Page 383 and 384:
a. Insulation, whether hot or cold
Page 385 and 386:
Hot Domestic Mineral Fiber ASTM C 5
Page 387 and 388:
level. Other areas that specificall
Page 389 and 390:
Factory precut or premolded insulat
Page 391 and 392:
3.2.5.1 Type of Insulation Below gr
Page 393 and 394:
j. Filter boxes. k. Mixing boxes (f
Page 395 and 396:
c. Insulation shall be impaled on t
Page 397 and 398:
ought up to standing seams, reinfor
Page 399 and 400:
c. Drip pans under chilled equipmen
Page 401 and 402:
e. Exposed insulation corners shall
Page 403 and 404:
igid housing that does not rest on
Page 405 and 406:
SECTION 23 09 23 DIRECT DIGITAL CON
Page 407 and 408:
UL 94 (1996; Rev thru Jun 2009) Tes
Page 409 and 410:
ff. Service Pin: A hardware push-bu
Page 411 and 412:
. The hardware shall perform the co
Page 413 and 414:
1.6 QUALITY CONTROL (QC) CHECKLISTS
Page 415 and 416:
shall be made without prior approva
Page 417 and 418:
(2) Products installed outdoors or
Page 419 and 420:
an overall aluminum-polyester or ti
Page 421 and 422:
2.7.3.2 Mechanical Rooms and Other
Page 423 and 424:
2.8.2.4 Thermowells Thermowells sha
Page 425 and 426:
2.8.6.2 Current Sensing Relays (CSR
Page 427 and 428:
2.10.1.1 Valve Actuators Valve actu
Page 429 and 430:
c. It shall incorporate a TP/FT-10
Page 431 and 432:
complete application necessary for
Page 433 and 434:
A temperature limit switch (freezes
Page 435 and 436:
ass or acetal resin of the compress
Page 437 and 438:
the Government. Sequences of operat
Page 439 and 440:
Occupancy Output shall be determine
Page 441 and 442:
activation of any safety shall resu
Page 443 and 444:
e. Minimum Outside Air Flow Control
Page 445 and 446:
(2) Unoccupied mode: While the buil
Page 447 and 448:
systems served by this system are n
Page 449 and 450:
climatic season. When simulation is
Page 451 and 452:
APPENDIX A QC CHECKLIST This checkl
Page 453 and 454:
SECTION 23 11 25 FACILITY GAS PIPIN
Page 455 and 456:
CSA/AM Z21.15 CSA/AM Z21.24 CSA/AM
Page 457 and 458:
Welders procedures and qualificatio
Page 459 and 460:
2.2.7 Pipe Threads Provide pipe thr
Page 461 and 462:
3.3.1 Protection and Cleaning of Ma
Page 463 and 464:
Do not embed piping in concrete sla
Page 465 and 466:
fire-stopping material and sealant
Page 467 and 468:
3.17 PIPE COLOR CODE MARKING Provid
Page 469 and 470:
ASME B16.24 ASME B16.3 ASME B16.34
Page 471 and 472:
MSS SP-80 MSS SP-85 (2008) Bronze G
Page 473 and 474:
Backflow preventers External air se
Page 475 and 476:
1.6.2 Guards Couplings, motor shaft
Page 477 and 478:
2.1.6.1 Steel Pipe ASTM A 53/A 53M,
Page 479 and 480:
inches shall have throttling handle
Page 481 and 482:
the same composition. Provide conti
Page 483 and 484:
Select pumps so that the operating
Page 485 and 486:
Sleeves shall be of sufficient leng
Page 487 and 488:
3.2.16 Cleaning of Systems As insta
Page 489 and 490:
SECTION 23 25 00 CHEMICAL TREATMENT
Page 491 and 492:
accordingly, furnishing required of
Page 493 and 494:
One test kit of each type required
Page 495 and 496:
Install corrosion coupon and rack s
Page 497 and 498:
NFPA 90A (2008; Errata 2009) Standa
Page 499 and 500:
Flexible Duct Materials Power Opera
Page 501 and 502:
2.2 COMPONENTS 2.2.1 Round Sheet Me
Page 503 and 504:
polyvinylchloride film. Duct shall
Page 505 and 506:
Clean free of oil, grease, and dele
Page 507 and 508:
Install access doors and panels in
Page 509 and 510:
133 and 14 2 by 2 by 3/16, Two 2 by
Page 511 and 512:
Flanges shall be continuously welde
Page 513 and 514:
with lesser spans as required by du
Page 515 and 516:
3.4.3 Inspection 3.5 DUCTWORK CLEAN
Page 517 and 518:
ASTM A 653/A 653M ASTM B 209 ASTM B
Page 519 and 520:
For Type CB-PRV ventilator provide
Page 521 and 522:
SECTION 23 37 13 DIFFUSERS, REGISTE
Page 523 and 524:
2.2.1 Type DRC Provide type DRC com
Page 525 and 526:
Provide aluminum construction. 2.2.
Page 527 and 528:
SECTION 23 52 43.00 20 LOW PRESSURE
Page 529 and 530:
. Gas-Fired Units: ANSI Z83.3, CSA
Page 531 and 532:
Provide and locate on wall outside
Page 533 and 534:
Provide alarm bell not less than 4
Page 535 and 536:
Separate waste in accordance with t
Page 537 and 538:
Government approval is required for
Page 539 and 540:
certification program that encompas
Page 541 and 542:
Manufacturer:_______Model No.:_____
Page 543 and 544:
d. Controls package e. Scroll, reci
Page 545 and 546:
2.5.4.4 Safety Controls with Manual
Page 547 and 548:
starter type, wiring, and accessori
Page 549 and 550:
shall be applied in such a manner t
Page 551 and 552:
if the leak is the result of defect
Page 553 and 554:
Controller shall be verified to be
Page 555 and 556:
(5) The actual on-site setting of a
Page 557 and 558:
ASME B16.21 ASME B16.22 ASME B16.26
Page 559 and 560:
HYDRAULIC INSTITUTE (HI) HI 1.1-1.2
Page 561 and 562:
listed in paragraph "Water Analysis
Page 563 and 564:
1.4.2 Administrative Interpretation
Page 565 and 566:
Flanges shall conform to ASME B16.1
Page 567 and 568:
Filler metal shall conform to AWS A
Page 569 and 570:
integral pointer on the valve which
Page 571 and 572:
Gauges, ASME B40.100 with throttlin
Page 573 and 574:
Each pump casing shall be designed
Page 575 and 576:
2.9.2 Chilled and Condenser Water W
Page 577 and 578:
thickness of one mil; and two coats
Page 579 and 580:
. List of qualified welders, brazer
Page 581 and 582:
grooving tool setup to verify compl
Page 583 and 584:
3.1.10.7 Vertical Pipe Supports Ver
Page 585 and 586:
3.1.12.3 Fire-Rated Penetrations Pe
Page 587 and 588:
-- End of Section -- Section 23 64
Page 589 and 590:
NATIONAL ELECTRICAL MANUFACTURERS A
Page 591 and 592:
to ASTM A 653/A 653M and that is co
Page 593 and 594:
Provide single-wheel fans. Locate f
Page 595 and 596:
2.7.4 Chilled Water coils Provide 0
Page 597 and 598:
After systems have been cleaned and
Page 599 and 600:
1.2 SUBMITTALS Government approval
Page 601 and 602:
3RD 4TH 5TH 6TH 7TH Frequency 250 5
Page 603 and 604:
Install equipment as indicated and
Page 605 and 606:
Section 33 82 00 TELECOMMUNICATIONS
Page 607 and 608:
1.9 MANUFACTURER'S NAMEPLATE Each i
Page 609 and 610:
SECTION 26 05 00.00 40 COMMON WORK
Page 611 and 612:
1.2 DEFINITIONS a. Unless otherwise
Page 613 and 614:
Submit manufacturer's instructions
Page 615 and 616:
2.1.4 Intermediate Metal Conduit In
Page 617 and 618:
ated. Fluorescent lamps shall be st
Page 619 and 620:
CONDUCTOR Neutral Equipment Grounds
Page 621 and 622:
3.11 FIELD TESTING Perform PT&I tes
Page 623 and 624:
cables rated 2,001 volts and above
Page 625 and 626:
Section D of AEIC C8 or AEIC CS8, a
Page 627 and 628:
a. Minimum bending radius, in inche
Page 629 and 630:
___________________________________
Page 631 and 632:
to 40 GHz IPC - ASSOCIATION CONNECT
Page 633 and 634:
Protective Devices G SD-10 Operatio
Page 635 and 636:
starters at a maximum of 120 volts
Page 637 and 638:
Preferred Radio Influence Basic Nom
Page 639 and 640:
atmospheres in NEMA Type 12 dusttig
Page 641 and 642:
secured. Provide nonrenewable cartr
Page 643 and 644:
switch rated for 600 volts, 20 ampe
Page 645 and 646:
2.8.2 Directional Overcurrent Relay
Page 647 and 648:
kilowatt demand of the totalized sy
Page 649 and 650:
SECTION 26 09 23.00 40 LIGHTING CON
Page 651 and 652:
Provide photoconductive control dev
Page 653 and 654:
adjustable sensitivity, and adjusta
Page 655 and 656:
SECTION 26 12 19.10 THREE-PHASE PAD
Page 657 and 658:
ORGANISATION FOR ECONOMIC CO-OPERAT
Page 659 and 660:
f. Provide acceptance test reports
Page 661 and 662:
handle(s), access to oil-immersed b
Page 663 and 664:
interrupting rating of the expulsio
Page 665 and 666:
kVA DECIBELS (MAX 75 51 112.5 55 15
Page 667 and 668:
Paint entire transformer assembly M
Page 669 and 670:
2. State test voltage levels. 3. Pr
Page 671 and 672:
3.6.1 Cast-In-Place Concrete Cast-i
Page 673 and 674:
and on moving and sliding surfaces.
Page 675 and 676:
SECTION 26 20 00 INTERIOR DISTRIBUT
Page 677 and 678:
TELECOMMUNICATIONS INDUSTRY ASSOCIA
Page 679 and 680:
1.3 SUBMITTALS Government approval
Page 681 and 682:
1.4.3.1 Alternative Qualifications
Page 683 and 684:
zinc-coated after fabrication. Tray
Page 685 and 686:
2.7.5 Cord Sets and Power-Supply Co
Page 687 and 688:
directories for existing panels mod
Page 689 and 690:
2.15.2 Premium Efficiency Polyphase
Page 691 and 692:
2.16.3 Control Circuits Control cir
Page 693 and 694:
Each phase to neutral ( L-N ) Neutr
Page 695 and 696:
3.1.4.2 Restrictions Applicable to
Page 697 and 698:
system. Conduit and box systems sha
Page 699 and 700:
3.1.6.3 Extension Rings Extension r
Page 701 and 702:
3.1.12.3 Resistance Maximum resista
Page 703 and 704:
3.5 FIELD QUALITY CONTROL Furnish t
Page 705 and 706:
Statements signed by responsible of
Page 707 and 708:
eakers can be installed at any loca
Page 709 and 710:
Panelboards shall be given continui
Page 711 and 712:
shall conform to NFPA 70, NFPA 780,
Page 713 and 714:
2.2.3 Connections and Terminations
Page 715 and 716:
to ground using the fall-of-potenti
Page 717 and 718:
and grounding electrodes are not re
Page 719 and 720:
SECTION 26 51 00 INTERIOR LIGHTING
Page 721 and 722:
UL 935 (2001; Reprint Jun 2010) Sta
Page 723 and 724:
approval. The sample shall be retai
Page 725 and 726:
Current crest factor shall be 1.7 (
Page 727 and 728:
2.2 SUSPENDED FIXTURES Provide hang
Page 729 and 730:
2.11 SUPPORT HANGERS FOR LIGHTING F
Page 731 and 732:
specified. Pendants shall be finish
Page 733 and 734:
SD-07 Certificates Materials and Eq
Page 735 and 736:
3.1.1 Horizontal Cable Installation
Page 737 and 738:
SECTION 27 05 28.36 40 CABLE TRAYS
Page 739 and 740:
PART 3 EXECUTION Comply with NEMA V
Page 741 and 742:
(Earthing) and Bonding Requirements
Page 743 and 744:
1.3.9 Pathway A physical infrastruc
Page 745 and 746:
laminated schematic of the as-insta
Page 747 and 748:
years experience in the manufacturi
Page 749 and 750:
PART 2 PRODUCTS 2.1 COMPONENTS Comm
Page 751 and 752:
2.4.5 Patch Panels Provide ports fo
Page 753 and 754:
this section. 3.1.1.1 Backbone Cabl
Page 755 and 756:
or to meet the indicated or specifi
Page 757 and 758:
SECTION 28 16 01.00 10 SMALL INTRUS
Page 759 and 760:
Submit the following: a. System blo
Page 761 and 762:
1.5.4 Line Supervision 1.5.4.1 Sign
Page 763 and 764:
2.1.2.2 Interior Electronics System
Page 765 and 766:
facility. 2.1.8 Alarm Output The al
Page 767 and 768:
at least 8 alarm inputs which allow
Page 769 and 770:
i. Download and upload data to and
Page 771 and 772:
. Calibrate and test all equipment,
Page 773 and 774:
UL 464 UL 521 UL 6 UL 797 UL 864 (2
Page 775 and 776:
elays for HVAC shutdown. An overrid
Page 777 and 778:
. National Institute for Certificat
Page 779 and 780:
that can provide service within 24
Page 781 and 782:
2.5 BATTERY CHARGER Battery charger
Page 783 and 784:
2.7.3 Combination Smoke and Heat De
Page 785 and 786:
terminal then clamped in place unde
Page 787 and 788:
3.5.2 Additions to Existing Facilit
Page 789:
l. Stray voltage. m. Loop resistanc
show all

Specifications - Lord and Son Construction, Inc.

Create successful ePaper yourself

Delete template?

Save as template?