Design and Construction Handbook - Los Angeles World Airports

More documents

Recommendations

Info

Guide Specification 5. Intelligibility Performance; objective measurements of intelligibility, as referenced in IEC standard 60268-16, shall be performed in all representative acoustical environments. Representative acoustical environments are defined as major functional areas such as Baggage Claim areas, Departures Ticketing Lobby, Departures Hold Rooms, etc. Measurements are to meet or exceed standards established by IEC 60849 which calls for a ‘Common Intelligibility Scale’ greater than or equal to 0.7 (STI equivalent of 0.5). Measurements shall be carried out according to all provisions and limitations as provided by IEC 60849. B. Ambient Noise Analysis System: 1. Shall be adjusted in each zone to provide variable attenuation in the range of 0 to -10dB. To be calibrated to correspond with minimum and maximum expected ambient noise levels, but not to exceed 10dB, + or – 3dB, above maximum ambient noise level, as measured when area is full of people. Ambient Noise Analysis System must be calibrated by a manufacturer-approved consultant, and calibration process must include at least 2 follow-up visits which measure all representative acoustical environments. Observations and measurements must be submitted in written form. 2. Contractor shall confirm that ambient microphone positions are not located in close proximity to noise emitting equipment which turns on and off intermittently, providing false ambient noise information to the system. C. Monitor/Test System: Shall perform routine, automatic diagnostic tests utilizing a selfgenerated test tone. Refer to manufacturer’s instructions and recommendations for settings. D. Each output zone shall be adjusted at the corresponding power amplifier and using the system software so that volume levels (using an appropriate pink noise source) from zone to adjacent zone are within 3dB of each other, before any Ambient Noise System auto-attenuation takes place. E. General Network Requirements: 1. A 100Mbps switched Ethernet network is required for general audio, switched at a layer 2 (MAC) protocol level throughout. 2. Microphone Station to ACS - One dedicated VLAN at 100Mbps. 3. Digital Amplifier to ACS - One dedicated VLAN at 100Mbps. 4. ACS to ACS - One dedicated VLAN at 100Mbps. 5. Quality of Service - QoS shall be used to give the time sensitive CobraNet data precedence over less sensitive computer traffic, insuring that other transactions occurring over the network do not affect audio delivery. 2.2 MAJOR EQUIPMENT A. Schedule of major equipment (or equivalent): PAGING SYSTEMS 27 51 13 - 19 Communication Systems
Guide Specification Description Mfr. Model Speakers: Ceiling Loudspeaker – 6.5” Atlas PAGING SYSTEMS 27 51 13 - 20 FAP 62T with and without custom hanger Ceiling Loudspeaker – 8” Atlas FAP 82T w. hanger Ceiling-mount speaker system EAW CP621 Wall speaker Amplifier and DSP Section: Atlas Sound SM42T-W Titan Mainframe System 120VAC IED TITANSYS-L Titan DSP Software IED T-DSP Titan Monitor/Test Software IED T-MON Titan Backup power amp switching software IED T-BACK Power Amp Card Dual 70-Volt 200W IED IED6272L 120VAC Power Amp Card 70-Volt 400W 120VAC Ambient Analysis Sensor Collector IED IED IED6470L IED6540TSYS- L Ambient Sensor Collector Software IED T-AMB Ambient Sensor - 2 Gang Plate IED IED0540S Headend Section: ACS "System" (includes cardframe, CPU, power supplies, and "R" card) IED IEDA500ACS- L Backup CPU/Hard Drive Card IED 510CPU Digital Frame link Card- Multimode with Back ST IED 510N and NT Microphone station input card and strip IED 500C and FT ACS Configuration Computer IED 591R-S1 UPS for ACS APC SU3000RMXL3U with one SUA48R3XLBP Relay input card (for Fire Alarm Interface) IED 508BI0 Telephone Interface IED 508T ACS Software IED IED0631 FAS Software IED Model 632 Network Switch with (2) single-mode fiber mini-GBICs and 10/100 ports HP Procurve 4104gl Communication Systems
Page 1 and 2:
Design and Construction Handbook Ap
Page 3 and 4:
1.31.6 Utilities 1.31.7 Product, Ma
Page 5 and 6:
22.11.00 Facility Water Distributio
Page 7 and 8:
Supplemental Drawings (To be issued
Page 9 and 10:
1.0 General Requirements 1.1 Scope,
Page 11 and 12:
inclusive of all information availa
Page 13 and 14:
The 2008 Los Angeles Electrical Cod
Page 15 and 16:
Design and Construction Handbook 15
Page 17 and 18:
1.15 Tenant Projects Approvals - Te
Page 19 and 20:
Issues Addressed Design Impacts to
Page 21 and 22:
e responsible for assisting in the
Page 23 and 24:
c. Egress Plan • Update Occupant
Page 25 and 26:
• Locate and identify employee ch
Page 27 and 28:
• Update sprinkler layout. • In
Page 29 and 30:
g. Zone Plan (if required). • Ind
Page 31 and 32:
• Identify all primary materials
Page 33 and 34:
• Locate all receptacles • Loca
Page 35 and 36:
3. Final Construction schedule, inc
Page 37 and 38:
Page 39 and 40:
Mechanical Drawings: a. Sheet Index
Page 41 and 42:
Communication Drawings: a. Sheet In
Page 43 and 44:
• Make certain that the signature
Page 45 and 46:
1. Piping shall be coordinated with
Page 47 and 48:
other facilities. Constantly secure
Page 49 and 50:
d. The face of the barricade expose
Page 51 and 52:
e) No unapproved signage such as wa
Page 53 and 54:
Page 55 and 56:
1.31.6 Utilities A. Pursuant to Sec
Page 57 and 58:
Utility Shutdowns A. Utility shutdo
Page 59 and 60:
Deviations: The Submittals shall cl
Page 61 and 62:
miscellaneous items, as included he
Page 63 and 64:
5) The Contractor shall comply with
Page 65 and 66:
1. Sediments or other surface water
Page 67 and 68:
Temporary Light, Power, Water, and
Page 69 and 70:
equirements listed and any other re
Page 71 and 72:
unauthorized persons to Airport-res
Page 73 and 74:
C. The Contractor shall notify the
Page 75 and 76:
E. All materials, parts, and equipm
Page 77 and 78:
N. See appendix B for typical items
Page 79 and 80:
or other characteristics, including
Page 81 and 82:
Page 83:
GUIDE SPECIFICATIONS INTRODUCTION I
Page 86 and 87:
Guide Specification bolts, and item
Page 88 and 89:
Guide Specification 2. Wall Bracket
Page 90 and 91:
Guide Specification 3.4 METAL BASE
Page 92 and 93:
Guide Specification 1.5 CLOSEOUT SU
Page 94 and 95:
Guide Specification 2.3 ILLUMINATIO
Page 96 and 97:
Guide Specification B. Glass Column
Page 98 and 99:
Guide Specification SECTION 06 40 2
Page 100 and 101:
Guide Specification humidity at lev
Page 102 and 103:
Guide Specification B. Solid-Surfac
Page 104 and 105:
Page 106 and 107:
Guide Specification 1.4 DELIVERY, S
Page 108 and 109:
Guide Specification 7. Exit Device
Page 110 and 111:
Guide Specification a. Three anchor
Page 112 and 113:
Guide Specification hardware. Facto
Page 114 and 115:
Guide Specification 3.2 ADJUSTING A
Page 116 and 117:
Guide Specification 1.3 INFORMATION
Page 118 and 119:
Guide Specification a. Welded Steel
Page 120 and 121:
Guide Specification b. Stud-Wall Ty
Page 122 and 123:
Guide Specification B. Stainless-St
Page 124 and 125:
Guide Specification B. Examine roug
Page 126 and 127:
Guide Specification D. Glazing: Ins
Page 128 and 129:
Guide Specification DOOR HARDWARE 0
Page 130 and 131:
Guide Specification 1.5 COORDINATIO
Page 132 and 133:
Guide Specification 2.2 HINGING MET
Page 134 and 135:
Guide Specification 1. 1100 Series
Page 136 and 137:
Guide Specification B. Size: Furnis
Page 138 and 139:
Guide Specification 1. All modifica
Page 140 and 141:
Page 142 and 143:
Guide Specification a. Diameter: 1/
Page 144 and 145:
Guide Specification NOTE: On the dr
Page 146 and 147:
Guide Specification 3.5 INSTALLING
Page 148 and 149:
GYPSUM BOARD 09 29 00 - 1 Guide Spe
Page 150 and 151:
Guide Specification NOTE: d. On the
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Guide Specification 1. Locate sampl
Page 160 and 161:
Guide Specification 2. Latex Additi
Page 162 and 163:
Guide Specification F. Movement (Ex
Page 164 and 165:
Guide Specification c. Immediately
Page 166 and 167:
Page 168 and 169:
Guide Specification Testing of Vola
Page 170 and 171:
Page 172 and 173:
Guide Specification 1. Build mockup
Page 174 and 175:
Guide Specification D. Control-Join
Page 176 and 177:
Guide Specification B. Installation
Page 178 and 179:
Page 180 and 181:
Guide Specification 1.6 PROTECTION
Page 182 and 183:
Guide Specification 1. Sizes shall
Page 184 and 185:
Guide Specification NOTE: the mix d
Page 186 and 187:
Guide Specification 4. Curing: Allo
Page 188 and 189:
Guide Specification 1. Probe Manufa
Page 190 and 191:
Guide Specification b. Stop Strips:
Page 192 and 193:
Guide Specification thoroughly. App
Page 194 and 195:
Guide Specification 1. Each carpet
Page 196 and 197:
Guide Specification F. Density: Gre
Page 198 and 199:
Guide Specification C. Butt carpet
Page 200 and 201:
Guide Specification 4. Mitered Carp
Page 202 and 203:
Guide Specification 4. Mannington 5
Page 204 and 205:
Guide Specification characteristics
Page 206 and 207:
Guide Specification END OF SECTION
Page 208 and 209:
Guide Specification 4. ICI Paints 5
Page 210 and 211:
Guide Specification 3.3 APPLICATION
Page 212 and 213:
SIGNAGE 10 14 23 - 1 Guide Specific
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
SIGNAGE 10 14 23 - 11 Guide Specifi
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
2.2 CORNER GUARDS A. Surface-Mounte
Page 236 and 237:
2. Provide full height units. Do no
Page 238 and 239:
Guide Specification 1.4 COORDINATIO
Page 240 and 241:
Guide Specification 2. Mounting: Fl
Page 242 and 243:
Guide Specification 2.6 CUSTODIAL A
Page 244 and 245:
Guide Specification 1. Review metho
Page 246 and 247:
Guide Specification B. Cabinet Door
Page 248 and 249:
Page 250 and 251:
Guide Specification 1. Shelf: Same
Page 252 and 253:
Guide Specification 3.3 INSTALLATIO
Page 254 and 255:
Guide Specification 1.7 WARRANTY A.
Page 256 and 257:
Page 258 and 259:
Guide Specification H. Shade Cloth
Page 260 and 261:
Guide Specification 4. The braking
Page 262 and 263:
Guide Specification d. Multiple "su
Page 264 and 265:
Page 266 and 267:
Guide Specification c. Single-phase
Page 268 and 269:
Guide Specification a. Clear, plumb
Page 270 and 271:
Guide Specification j. Single phase
Page 272 and 273:
Guide Specification 3. All electric
Page 274 and 275:
Guide Specification when copies of
Page 276 and 277:
Guide Specification 15) Safeties: C
Page 278 and 279:
Guide Specification safety devices
Page 280 and 281:
Guide Specification LAWA. This serv
Page 282 and 283:
Guide Specification 1) Replace: Rep
Page 284 and 285:
Guide Specification 2.1 MATERIALS A
Page 286 and 287:
Guide Specification A. General: On
Page 288 and 289:
Page 290 and 291:
Guide Specification 2. Samples shal
Page 292 and 293:
Guide Specification 1.5 DELIVERY, S
Page 294 and 295:
Guide Specification B. Optional Sec
Page 296 and 297:
Guide Specification L. Baked Enamel
Page 298 and 299:
Guide Specification Car and Hoistwa
Page 300 and 301:
Guide Specification C. Door Control
Page 302 and 303:
Guide Specification O. Terminal Lim
Page 304 and 305:
Guide Specification 2. Include as a
Page 306 and 307:
Guide Specification d. Elevator dep
Page 308 and 309:
Guide Specification 3. Protect car
Page 310 and 311:
Guide Specification a minimum dimen
Page 312 and 313:
Guide Specification F. Hall Lantern
Page 314 and 315:
Guide Specification seconds. Upon e
Page 316 and 317:
Guide Specification 9. All cabinets
Page 318 and 319:
Guide Specification C. Re-Inspectio
Page 320 and 321:
Guide Specification D. Step/Skirt P
Page 322 and 323:
Guide Specification K. Operation an
Page 324 and 325:
Guide Specification A. Installer Qu
Page 326 and 327:
Guide Specification 2.2 MATERIALS A
Page 328 and 329:
Guide Specification 3. Brake Operat
Page 330 and 331:
Guide Specification a. The motor co
Page 332 and 333:
Guide Specification 5. Step Tracks:
Page 334 and 335:
Guide Specification ends. Plates sh
Page 336 and 337:
Guide Specification building change
Page 338 and 339:
Guide Specification 35) Pit high wa
Page 340 and 341:
Guide Specification 3.4 DEMONSTRATI
Page 342 and 343:
Guide Specification 1.4 QUALITY ASS
Page 344 and 345:
Guide Specification a. Tools may be
Page 346 and 347:
Guide Specification 1.6 JOB CONDITI
Page 348 and 349:
Guide Specification C. Oil Drip Pan
Page 350 and 351:
Guide Specification G. Landing Floo
Page 352 and 353:
Guide Specification 1. Provide each
Page 354 and 355:
Guide Specification 1. Per Referenc
Page 356 and 357:
Guide Specification 1. Emergency St
Page 358 and 359:
Guide Specification F. Width: 56" (
Page 360 and 361:
Guide Specification PART 2 - PRODUC
Page 362 and 363:
Guide Specification PART 3 - EXECUT
Page 364 and 365:
Page 366 and 367:
Guide Specification 4. Joint: As sp
Page 368 and 369:
Guide Specification 3.2 MANUFACTURE
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Guide Specification 2.2 PIPING SPEC
Page 376 and 377:
Page 378 and 379:
Guide Specification 1. Type: Standa
Page 380 and 381:
Page 382 and 383:
2.4 VALVES Guide Specification a. M
Page 384 and 385:
Guide Specification B. Manual Relea
Page 386 and 387:
Guide Specification 3.3 CLEAN-AGENT
Page 388 and 389:
Guide Specification 1.3 SUBMITTALS
Page 390 and 391:
Guide Specification C. 2-1/2 inches
Page 392 and 393:
Guide Specification 2.5 BUTTERFLY V
Page 394 and 395:
Guide Specification 3.3 GENERAL REQ
Page 396 and 397:
Page 398 and 399:
Guide Specification 1. Hangers for
Page 400 and 401:
Guide Specification 2.9 FIRESTOPPIN
Page 402 and 403:
Guide Specification 2.13 PIPE POSIT
Page 404 and 405:
Guide Specification 20. Pipe Roll a
Page 406 and 407:
Guide Specification auxiliary stops
Page 408 and 409:
Guide Specification d. NPS 8 to NPS
Page 410 and 411:
Guide Specification N. Spring suppo
Page 412 and 413:
Page 414 and 415:
Guide Specification 1. Mass: Minimu
Page 416 and 417:
Guide Specification a. 0.750 inch m
Page 418 and 419:
Guide Specification 2.5 SEISMIC RES
Page 420 and 421:
Guide Specification D. Install spri
Page 422 and 423:
Guide Specification H. Drilled-in A
Page 424 and 425:
Page 426 and 427:
2.3 STENCILS Guide Specification c.
Page 428 and 429:
Guide Specification B. Valve Lockou
Page 430 and 431:
Guide Specification 2. Near each br
Page 432 and 433:
Page 434 and 435:
Guide Specification C. Mockups: Bef
Page 436 and 437:
Guide Specification H. TYPE P-8: AS
Page 438 and 439:
Guide Specification E. Closed Cell
Page 440 and 441:
Guide Specification D. Mineral Fibe
Page 442 and 443:
Guide Specification 3. Service Temp
Page 444 and 445:
Guide Specification C. Woven Polyes
Page 446 and 447:
Guide Specification C. Stainless-St
Page 448 and 449:
Guide Specification N. Heat Traced
Page 450 and 451:
Guide Specification PIPING SYSTEM D
Page 452 and 453:
Page 454 and 455:
Guide Specification 1. Mechanical-J
Page 456 and 457:
Guide Specification B. Remote Regis
Page 458 and 459:
Guide Specification 3. Stem: Copper
Page 460 and 461:
Guide Specification a. Watts. b. Zu
Page 462 and 463:
Guide Specification C. Refrigerator
Page 464 and 465:
Guide Specification 3. Refrigerator
Page 466 and 467:
Page 468 and 469:
Page 470 and 471:
Guide Specification 2.3 SANITARY SE
Page 472 and 473:
Guide Specification 1. Copper Pipin
Page 474 and 475:
Guide Specification 13. Type, for E
Page 476 and 477:
Guide Specification B. Cast Iron: A
Page 478 and 479:
Guide Specification 1. Structural D
Page 480 and 481:
Guide Specification D. Keep open en
Page 482 and 483:
Guide Specification sanitary sewer
Page 484 and 485:
Guide Specification 7. NPS 6: 12 fe
Page 486 and 487:
Guide Specification Q. Install expa
Page 488 and 489:
Page 490 and 491:
Guide Specification B. Manufacturer
Page 492 and 493:
Guide Specification B. Ductile-Iron
Page 494 and 495:
Guide Specification 2.6 STORM WATER
Page 496 and 497:
Guide Specification C. Area Drain (
Page 498 and 499:
Guide Specification C. Cover shall
Page 500 and 501:
Guide Specification 1. Power failur
Page 502 and 503:
Guide Specification 1. Galvanized s
Page 504 and 505:
Guide Specification 3. Multiple, St
Page 506 and 507:
Guide Specification 1. Lead Sheets:
Page 508 and 509:
Page 510 and 511:
Guide Specification b. Everpure, In
Page 512 and 513:
Page 514 and 515:
Page 516 and 517:
Guide Specification 1. Rheem. 2. A.
Page 518 and 519:
Guide Specification a. Thermometer
Page 520 and 521:
Guide Specification E. Shop Drawing
Page 522 and 523:
Guide Specification a. J.R. Smith.
Page 524 and 525:
Guide Specification 1. Sloan. 2. Ch
Page 526 and 527:
Guide Specification pitched to drai
Page 528 and 529:
2.9 MOP SINKS Guide Specification A
Page 530 and 531:
Guide Specification I. Install wate
Page 532 and 533:
Page 534 and 535:
Page 536 and 537:
Guide Specification B. Product Desc
Page 538 and 539:
Page 540 and 541:
Guide Specification 6. Ends: Thread
Page 542 and 543:
Guide Specification D. Gas safety s
Page 544 and 545:
Guide Specification E. One-Piece, S
Page 546 and 547:
Guide Specification C. Install gas
Page 548 and 549:
Guide Specification e. Piping in Eq
Page 550 and 551:
Guide Specification B. Install hang
Page 552 and 553:
Guide Specification C. Source Quali
Page 554 and 555:
Guide Specification h. Insert 2 cop
Page 556 and 557:
Guide Specification D. Access to Eq
Page 558 and 559:
Guide Specification and frames shal
Page 560 and 561:
Guide Specification 4. Purge all ai
Page 562 and 563:
Guide Specification B. Product Data
Page 564 and 565:
Guide Specification 2.3 ACCESSORIES
Page 566 and 567:
Page 568 and 569:
Guide Specification 1. Manufacturer
Page 570 and 571:
Guide Specification 3.3 CHILLED-WAT
Page 572 and 573:
Page 574 and 575:
Guide Specification D. Design Data:
Page 576 and 577:
Guide Specification C. Low-Type, Si
Page 578 and 579:
Guide Specification 2.11 FIRESTOPPI
Page 580 and 581:
Guide Specification C. Construct su
Page 582 and 583:
Page 584 and 585:
Guide Specification C. Restrained S
Page 586 and 587:
Guide Specification 2.3 DUCTWORK LA
Page 588 and 589:
Guide Specification 3. Wedge Anchor
Page 590 and 591:
Page 592 and 593:
Guide Specification 2. Brady. 3. Ko
Page 594 and 595:
Page 596 and 597:
Guide Specification drawings with a
Page 598 and 599:
Guide Specification B. Permanently
Page 600 and 601:
Guide Specification D. Measure, adj
Page 602 and 603:
Guide Specification c. Size/model d
Page 604 and 605:
Guide Specification k. Discharge pr
Page 606 and 607:
Guide Specification h. Minimum desi
Page 608 and 609:
Guide Specification 18. ASTM C1136
Page 610 and 611:
Guide Specification H. TYPE P-8: AS
Page 612 and 613:
Guide Specification 2. Density: 1.5
Page 614 and 615:
Guide Specification b. Pittsburgh C
Page 616 and 617:
Guide Specification 1. Insulate ent
Page 618 and 619:
Guide Specification P. Prepare pipe
Page 620 and 621:
Guide Specification G. Equipment in
Page 622 and 623:
Guide Specification Transfer Air Du
Page 624 and 625:
Page 626 and 627:
Guide Specification 1.7 COMMISSIONI
Page 628 and 629:
Guide Specification 2. Piping syste
Page 630 and 631:
Guide Specification 1. Test heating
Page 632 and 633:
Guide Specification 4. System confi
Page 634 and 635:
Guide Specification 2.2 OPERATOR WO
Page 636 and 637:
Guide Specification 6. Record, eval
Page 638 and 639:
Guide Specification 5. Add, delete,
Page 640 and 641:
Guide Specification 6. Data reports
Page 642 and 643:
Guide Specification a. Start. b. Op
Page 644 and 645:
Guide Specification 2. Base on occu
Page 646 and 647:
Guide Specification 1. Calculate ou
Page 648 and 649:
Page 650 and 651:
Guide Specification 1.3 SYSTEM DESC
Page 652 and 653:
Guide Specification 1. Fittings: AS
Page 654 and 655:
Guide Specification D. Sleeve pipe
Page 656 and 657:
Guide Specification PIPE SIZE Inche
Page 658 and 659:
Guide Specification B. Type: Horizo
Page 660 and 661:
Page 662 and 663:
Guide Specification B. Line Test Pr
Page 664 and 665:
Guide Specification 2.4 REFRIGERANT
Page 666 and 667:
Guide Specification 3. Sporlan Valv
Page 668 and 669:
Guide Specification B. Internal Dia
Page 670 and 671:
Guide Specification 2. When receive
Page 672 and 673:
Page 674 and 675:
Guide Specification 1. Water meters
Page 676 and 677:
Guide Specification 5. High or low
Page 678 and 679:
Guide Specification C. Provide glyc
Page 680 and 681:
Guide Specification source and allo
Page 682 and 683:
Guide Specification Metal and Flexi
Page 684 and 685:
Guide Specification 3. AWS D9.1M/D9
Page 686 and 687:
Guide Specification 1. Ducts up to
Page 688 and 689:
Guide Specification 7. Maximum Stat
Page 690 and 691:
Guide Specification D. Unless other
Page 692 and 693:
Guide Specification 8. Unconditione
Page 694 and 695:
3.9 PAINTING Guide Specification A.
Page 696 and 697:
3.12 START UP Guide Specification 2
Page 698 and 699:
Guide Specification a. Pressure Cla
Page 700 and 701:
Guide Specification a. Rectangular
Page 702 and 703:
Guide Specification 2. UL 555C - St
Page 704 and 705:
Guide Specification 9. 90-degree st
Page 706 and 707:
Guide Specification B. Fabrication:
Page 708 and 709:
Guide Specification 3. Operator: Mi
Page 710 and 711:
Guide Specification F. Bearings: 1.
Page 712 and 713:
Guide Specification h. Upstream and
Page 714 and 715:
Guide Specification 3.2 NSTALLATION
Page 716 and 717:
Page 718 and 719:
Guide Specification C. Sheaves: Cas
Page 720 and 721:
Page 722 and 723:
Guide Specification H. Hot Water He
Page 724 and 725:
Page 726 and 727:
Guide Specification 2.5 CEILING SUP
Page 728 and 729:
Guide Specification D. Fabrication:
Page 730 and 731:
Page 732 and 733:
Guide Specification C. Media: UL 90
Page 734 and 735:
Guide Specification 9. An integral
Page 736 and 737:
Guide Specification 1.4 WARRANTY in
Page 738 and 739:
Page 740 and 741:
Page 742 and 743:
Guide Specification B. Coil Guard:
Page 744 and 745:
Guide Specification C. Install the
Page 746 and 747:
Guide Specification E. If chiller a
Page 748 and 749:
Page 750 and 751:
Guide Specification 1.4 WARRANTY c.
Page 752 and 753:
Guide Specification motor and motor
Page 754 and 755:
Guide Specification 1. Type: R-134a
Page 756 and 757:
Guide Specification C. Designed to
Page 758 and 759:
Guide Specification C. Enclosure: U
Page 760 and 761:
Guide Specification 12. Total power
Page 762 and 763:
Guide Specification E. Manually Res
Page 764 and 765:
Guide Specification sagging. D. Too
Page 766 and 767:
Guide Specification mechanical coup
Page 768 and 769:
Guide Specification 3.7 COMMISSIONI
Page 770 and 771:
Page 772 and 773:
Guide Specification 7. Fan airflow,
Page 774 and 775:
Guide Specification 1. Material: St
Page 776 and 777:
Guide Specification GUARANTEED MINI
Page 778 and 779:
Guide Specification 4. Handrail: St
Page 780 and 781:
Guide Specification h. Verify prope
Page 782 and 783:
Guide Specification 1. NEMA MG 1 -
Page 784 and 785:
Guide Specification 1. Zinc chromat
Page 786 and 787:
2.5 COILS Guide Specification A. Ca
Page 788 and 789:
Guide Specification d. Axles: Minim
Page 790 and 791:
Guide Specification Method for Test
Page 792 and 793:
Page 794 and 795:
Guide Specification 4. Rough-in con
Page 796 and 797:
Guide Specification K. Air Filters:
Page 798 and 799:
Page 800 and 801:
Guide Specification f. National Fir
Page 802 and 803:
Guide Specification 32. Resistive L
Page 804 and 805:
Guide Specification 1.6 MAINTENANCE
Page 806 and 807:
Guide Specification deems a critica
Page 808 and 809:
Guide Specification 1. Hubbell. 2.
Page 810 and 811:
Page 812 and 813:
Guide Specification B. Location: In
Page 814 and 815:
Guide Specification B. Inspect cabl
Page 816 and 817:
Guide Specification 3.1 CONDUCTOR A
Page 818 and 819:
Page 820 and 821:
Guide Specification 2.3 TERMINATION
Page 822 and 823:
Page 824 and 825:
Guide Specification 2.1 ROD ELECTRO
Page 826 and 827:
Guide Specification J. Install from
Page 828 and 829:
Guide Specification 1.3 DEFINITIONS
Page 830 and 831:
Guide Specification damage, by stor
Page 832 and 833:
Guide Specification 5. Mechanical F
Page 834 and 835:
Guide Specification spring lock was
Page 836 and 837:
Guide Specification A. Clean adjace
Page 838 and 839:
Guide Specification F. In Slab Abov
Page 840 and 841:
Guide Specification 2. Allied Tube
Page 842 and 843:
Guide Specification 1. Material: Ga
Page 844 and 845:
Guide Specification U. Install suit
Page 846 and 847:
Page 848 and 849:
Page 850 and 851:
Page 852 and 853:
Guide Specification 1.6 PROJECT CON
Page 854 and 855:
Guide Specification C. Design and f
Page 856 and 857:
Guide Specification clean surfaces
Page 858 and 859:
Guide Specification with structural
Page 860 and 861:
Guide Specification 3.4 MANHOLE AND
Page 862 and 863:
Page 864 and 865:
Page 866 and 867:
Guide Specification D. Holes for Ex
Page 868 and 869:
Page 870 and 871:
Guide Specification voltage between
Page 872 and 873:
Guide Specification locations. 6. I
Page 874 and 875:
Guide Specification 1.2 REFERENCES
Page 876 and 877:
Page 878 and 879:
Guide Specification 1.5 QUALITY ASS
Page 880 and 881:
Guide Specification B. Arc fault ha
Page 882 and 883:
Guide Specification description of
Page 884 and 885:
Guide Specification equipment for t
Page 886 and 887:
Page 888 and 889:
Guide Specification and type of swi
Page 890 and 891:
Guide Specification 1. Cover Mounte
Page 892 and 893:
Guide Specification 2. Separate tri
Page 894 and 895:
Page 896 and 897:
Guide Specification D. Provide 2 ex
Page 898 and 899:
Guide Specification 5. The DTC shal
Page 900 and 901:
Guide Specification 3.2 DOCUMENTATI
Page 902 and 903:
Page 904 and 905:
Guide Specification the installatio
Page 906 and 907:
Guide Specification Maximum Voltage
Page 908 and 909:
Guide Specification F. Each breaker
Page 910 and 911:
Guide Specification u. Demand and P
Page 912 and 913:
Guide Specification B. Voltage and
Page 914 and 915:
Guide Specification a. Safety: UL 6
Page 916 and 917:
Guide Specification b. Waveforms sh
Page 918 and 919:
Guide Specification a. Eight (8) di
Page 920 and 921:
Guide Specification A. The switchge
Page 922 and 923:
Guide Specification ANSI standards.
Page 924 and 925:
Page 926 and 927:
Guide Specification I. Basic Impuls
Page 928 and 929:
Guide Specification B. Use flexible
Page 930 and 931:
Guide Specification 10. Cable termi
Page 932 and 933:
Page 934 and 935:
2.4 BUS Guide Specification H. An i
Page 936 and 937:
Guide Specification control circuit
Page 938 and 939:
Guide Specification for remote sett
Page 940 and 941:
Guide Specification 2.10 ENCLOSURES
Page 942 and 943:
Guide Specification B. The training
Page 944 and 945:
Guide Specification B. Product Data
Page 946 and 947:
Guide Specification 2.2 MOLDED CASE
Page 948 and 949:
Guide Specification C. Allow witnes
Page 950 and 951:
Page 952 and 953:
Page 954 and 955:
Guide Specification C. Submit dimen
Page 956 and 957:
Page 958 and 959:
Page 960 and 961:
Guide Specification 1.4 CLOSEOUT SU
Page 962 and 963:
Guide Specification 3.2 FIELD QUALI
Page 964 and 965:
Guide Specification 2.1 HINGED COVE
Page 966 and 967:
Page 968 and 969:
Guide Specification C. Configuratio
Page 970 and 971:
Guide Specification 3.7 CLEANING A.
Page 972 and 973:
Guide Specification A. Manufacturer
Page 974 and 975:
Guide Specification A. Manufacturer
Page 976 and 977:
Page 978 and 979:
Page 980 and 981:
Guide Specification A. Project Reco
Page 982 and 983:
Guide Specification protected by ar
Page 984 and 985:
Guide Specification E. Sequence of
Page 986 and 987:
Guide Specification switch is in no
Page 988 and 989:
Guide Specification 2.3 SOURCE QUAL
Page 990 and 991:
Page 992 and 993:
Guide Specification 4. Pushbuttons:
Page 994 and 995:
Page 996 and 997:
Page 998 and 999:
Guide Specification complete contro
Page 1000 and 1001:
Guide Specification in accordance w
Page 1002 and 1003:
Guide Specification 2.10 RADIATOR M
Page 1004 and 1005:
Guide Specification connecting to t
Page 1006 and 1007:
Page 1008 and 1009:
Page 1010 and 1011:
Guide Specification B. Design Requi
Page 1012 and 1013:
Page 1014 and 1015:
Guide Specification 1. Wiring pract
Page 1016 and 1017:
Guide Specification C. Inverter 7.
Page 1018 and 1019:
Guide Specification (3) DC Under vo
Page 1020 and 1021:
Guide Specification 5. Controls (2)
Page 1022 and 1023:
Guide Specification 2. Isolation a.
Page 1024 and 1025:
Guide Specification a. Eight sets o
Page 1026 and 1027:
Page 1028 and 1029:
Page 1030 and 1031:
Guide Specification and the followi
Page 1032 and 1033:
Guide Specification 3. Neutral to G
Page 1034 and 1035:
Page 1036 and 1037:
Guide Specification 1.11 WARRANTIES
Page 1038 and 1039:
Guide Specification 1. Philips. 2.
Page 1040 and 1041:
Page 1042 and 1043:
Guide Specification G. Submit all f
Page 1044 and 1045:
Guide Specification 14. ANSI/TIA/EI
Page 1046 and 1047:
Guide Specification 7. The listing
Page 1048 and 1049:
Guide Specification H. The Contract
Page 1050 and 1051:
Guide Specification B. Provide 4-po
Page 1052 and 1053:
Guide Specification D. Acceptable M
Page 1054 and 1055:
Guide Specification Baggage Handlin
Page 1056 and 1057:
Guide Specification 3.2 PHASES OF I
Page 1058 and 1059:
Guide Specification 3.7 SYSTEM STAR
Page 1060 and 1061:
H. I. J. K. L. M. Guide Specificati
Page 1062 and 1063:
Guide Specification 3.13 COMPUTERIZ
Page 1064 and 1065:
Guide Specification 1.3 MATERIALS O
Page 1066 and 1067:
Guide Specification E. Storage or s
Page 1068 and 1069:
Guide Specification F. Existing Ite
Page 1070 and 1071:
Guide Specification C. Refrigerant:
Page 1072 and 1073:
Page 1074 and 1075: Guide Specification F. Post changes
Page 1076 and 1077: Guide Specification 1.7 EQUIPMENT C
Page 1078 and 1079: Guide Specification Contractor is r
Page 1080 and 1081: Guide Specification PART 3 - EXECUT
Page 1082 and 1083: Guide Specification O. Spare condui
Page 1084 and 1085: Guide Specification 3.6 COMPUTERIZE
Page 1086 and 1087: Guide Specification O. NEMA Nationa
Page 1088 and 1089: Guide Specification 5. ANSI/TIA/EIA
Page 1090 and 1091: Guide Specification D. Major items
Page 1092 and 1093: Guide Specification 2. The system s
Page 1094 and 1095: Guide Specification 7. Web-Based/Cl
Page 1096 and 1097: Guide Specification 2.4 FIRESTOPPIN
Page 1098 and 1099: Guide Specification B. Upon concurr
Page 1100 and 1101: Guide Specification 7. Termination
Page 1102 and 1103: Guide Specification 1) After conclu
Page 1104 and 1105: Guide Specification C. All indoor c
Page 1106 and 1107: Guide Specification SECTION 27 51 1
Page 1108 and 1109: Guide Specification PAGING SYSTEMS
Page 1110 and 1111: Guide Specification C. System insta
Page 1112 and 1113: Guide Specification H. All audio sw
Page 1114 and 1115: Guide Specification 1. The PDRP sys
Page 1116 and 1117: Guide Specification S. Monitor/test
Page 1120 and 1121: Guide Specification 1.6 QUALITY ASS
Page 1122 and 1123: Guide Specification warranty period
Page 1126 and 1127: Guide Specification Custom software
Page 1128 and 1129: Guide Specification Fire Stop Syste
Page 1130 and 1131: Guide Specification 1. On-Site Perf
Page 1132 and 1133: Guide Specification D. Endurance Te
Page 1136 and 1137: Guide Specification 5. Absence of g
Page 1138 and 1139: Guide Specification 3. Freedom From
Page 1140 and 1141: Guide Specification inspection, LAW
Page 1142 and 1143: Guide Specification security contra
Page 1144 and 1145: Guide Specification 1. Provide shop
Page 1146 and 1147: Guide Specification 10. Record draw
Page 1148 and 1149: Guide Specification 6. 49 CFR 1520
Page 1150 and 1151: Guide Specification 5. Where applic
Page 1152 and 1153: Guide Specification Contractor is r
Page 1154 and 1155: Guide Specification 2. GE DOR model
Page 1156 and 1157: Guide Specification a. Cooper Notif
Page 1158 and 1159: Guide Specification 2.6 FIRESTOPPIN
Page 1160 and 1161: Guide Specification a. Floors - thr
Page 1162 and 1163: Guide Specification 5. All equipmen
Page 1164 and 1165: Guide Specification 3.5 INSPECTIONS
Page 1166 and 1167: Guide Specification 7. The test pro
Page 1168 and 1169: Guide Specification c. Receipt of w
Page 1170 and 1171: Guide Specification 2. The Contract
Page 1172 and 1173: Guide Specification inspection, LAW
Page 1174 and 1175:
Guide Specification camera cannot b
Page 1176 and 1177:
Guide Specification G. Installation
Page 1178 and 1179:
Guide Specification 1. In addition
Page 1180 and 1181:
Guide Specification 9. 49 CFR 1544
Page 1182 and 1183:
Page 1184 and 1185:
Guide Specification K. Following ea
Page 1186 and 1187:
Guide Specification c. CIF d. QCIF
Page 1188 and 1189:
Guide Specification 14. Dome: Dome
Page 1190 and 1191:
Guide Specification 5. Frame Rate s
Page 1192 and 1193:
Guide Specification H. Wire and Cab
Page 1194 and 1195:
Guide Specification E. The Contract
Page 1196 and 1197:
Guide Specification suggested means
Page 1198 and 1199:
Guide Specification 3.4 IDENTIFICAT
Page 1200 and 1201:
Guide Specification C. In addition
Page 1202 and 1203:
Guide Specification 7. Termination
Page 1204 and 1205:
Guide Specification VIDEO SURVEILLA
Page 1206 and 1207:
Guide Specification b. An operation
Page 1208 and 1209:
Guide Specification 14. State of Ca
Page 1210 and 1211:
Guide Specification 2. Initiating D
Page 1212 and 1213:
Guide Specification 3) Occupied Roo
Page 1214 and 1215:
Guide Specification B. Elevator Lob
Page 1216 and 1217:
Guide Specification 1. The point-to
Page 1218 and 1219:
Guide Specification panel, a separa
Page 1220 and 1221:
Guide Specification 1. The fire ala
Page 1222 and 1223:
Guide Specification 3. In the event
Page 1224 and 1225:
Guide Specification 2. Network alph
Page 1226 and 1227:
Guide Specification program control
Page 1228 and 1229:
Guide Specification 2. The percent
Page 1230 and 1231:
Guide Specification 3. The module s
Page 1232 and 1233:
Guide Specification and to insure t
Page 1234 and 1235:
Guide Specification 8. It shall be
Page 1236 and 1237:
Guide Specification 3. All non-addr
Page 1238 and 1239:
Guide Specification I. End of Line
Page 1240 and 1241:
Norman Y. Mineta San José Internat
Page 1242 and 1243:
Page 1244 and 1245:
Page 1246 and 1247:
Page 1248 and 1249:
Page 1250 and 1251:
Page 1252 and 1253:
Page 1254 and 1255:
Page 1256 and 1257:
Page 1258 and 1259:
Page 1260 and 1261:
Page 1262 and 1263:
Page 1264 and 1265:
Page 1266 and 1267:
Page 1268 and 1269:
Page 1270 and 1271:
Page 1272 and 1273:
Page 1274 and 1275:
Page 1276 and 1277:
Page 1278 and 1279:
Page 1280 and 1281:
Page 1 of 10 GENERAL CONDITIONS GC-
Page 1282 and 1283:
specified coverages shall be filed
Page 1284 and 1285:
GC-19. WAIVER 19.01 The waiver by C
Page 1286 and 1287:
Page 7 of 10 other unsuitability to
Page 1288 and 1289:
Page 1 of 10 SPECIAL CONDITIONS SC-
Page 1290 and 1291:
SC-9. OPERATION OF VEHICLES 9.01 Co
Page 1292 and 1293:
14.02 Cleaning of Site: The Contrac
Page 1294 and 1295:
Page 7 of 10 7. Annual clean down o
Page 1296 and 1297:
SC-19. REPORTS 19.01 Unless specifi
show all

Design and Construction Handbook - Los Angeles World Airports

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?