ATLAS 550 System Manual - Adtran

More documents

Recommendations

Info

Section 4 User Interface Guide ATLAS 550 System Manual MODULES (BONDING) > CONFIGURATION > TXINIT TIMER (SEC) Write security: 3; Read security: 5 Specifies the length of time the originating endpoint attempts to detect the BONDING negotiation pattern from the answering endpoint before deciding the BONDING call has failed. MODULES (BONDING) > CONFIGURATION > TXFA TIMER (SEC) Write security: 3; Read security: 5 Specifies the length of time both endpoints attempt to detect the BONDING frame pattern when a call is connected before deciding the BONDING call has failed. When interoperating with other manufacturers' BONDING equipment, it may be necessary to change this time so that it matches TXADD01. MODULES (BONDING) > CONFIGURATION > TXADD01 TIMER (SEC) Write security: 3; Read security: 5 Specifies the length of time both endpoints wait for additional calls to be connected at the end of negotiation before deciding that the BONDING call has failed. The factory default setting is sufficient for most calls to connect, although when dialing overseas it may be necessary to lengthen this timer to allow for slower call routing. MODULES (BONDING) > CONFIGURATION > TXDEQ TIMER (SEC) Write security: 3; Read security: 5 Specifies the length of time both endpoints attempt to equalize the network delay between the bearer channels before deciding the BONDING call has failed. MODULES (BONDING) > CONFIGURATION > TANULL TIMER (SEC) Write security: 3; Read security: 5 Specifies the length of time the answering endpoint attempts to detect the BONDING negotiation pattern from the originating endpoint before deciding the BONDING call has failed. It may be necessary to shorten this timer if the DTE equipment using the BONDING module also has timer constraints for completing non-BONDING parameter negotiation. MODULES (BONDING) > CONFIGURATION > TCID TIMER (SEC) Write security: 3; Read security: 5 Specifies the length of time both endpoints attempt to negotiate an agreeable value for bearer channels and channel capacities before deciding the BONDING call has failed. 186 © 2004 ADTRAN, Inc. 61200305L2-1B
ATLAS 550 System Manual Section 4 User Interface Guide MODULES (BONDING) > CONFIGURATION > CALL STAGGER Write security: 3; Read security: 5 Specifies the amount of delay between placing calls for outgoing BONDING sessions. The following call stagger values are available: NO STAGGER There is no delay between the call dialing of a BONDING session. 500 MS Wait approximately ½ second between the call dialing of a BONDING session. 1 SEC. Wait approximately 1 second between the call dialing of a BONDING session. 2 SEC. Wait approximately 2 seconds between the call dialing of a BONDING session. PACKET MANAGER The PACKET MANAGER submenus define and configure all layer 2 connections, including frame relay endpoints (Figure 14). These submenus include PACKET ENDPNTS, PACKET CNCTS, CNCTS SORT and FRAME RELAY IQ. Figure 14. Packet Manager Menu PACKET MANAGER > PACKET ENDPNTS Read security: 5 Defines, monitors, and tests a packet endpoint. Submenus include STATUS, PERFORMANCE, CONFIG, TEST, ENDPNT COUNT, and ENDPNTS SORT. 61200305L2-1B © 2004 ADTRAN, Inc. 187
Page 1 and 2:
61200305L2-1B August 2004 ATLAS 550
Page 3 and 4:
ATLAS 550 System Manual Revision Hi
Page 5 and 6:
ATLAS 550 System Manual Compliance
Page 7 and 8:
ATLAS 550 System Manual Industry Ca
Page 9 and 10:
ATLAS 550 System Manual Affidavit f
Page 11 and 12:
ATLAS 550 System Manual Warranty an
Page 13 and 14:
ATLAS 550 System Manual Customer Se
Page 15 and 16:
Table of Contents Section 1 System
Page 17 and 18:
SYSTEM DESCRIPTION Provides an over
Page 19 and 20:
ATLAS 550 System Manual Section 1 S
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
ENGINEERING GUIDELINES Provides equ
Page 27 and 28:
ATLAS 550 System Manual Section 2 E
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
NETWORK TURNUP PROCEDURE Provides s
Page 53 and 54:
ATLAS 550 System Manual Section 3 N
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
USER INTERFACE GUIDE Provides detai
Page 65 and 66:
ATLAS 550 System Manual Section 4 U
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136: ATLAS 550 System Manual Section 4 U
Page 185: ATLAS 550 System Manual Section 4 U
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
DETAIL LEVEL PROCEDURES DLP-1 Conne
Page 311 and 312:
DLP-1 Connecting a VT100 Terminal o
Page 313 and 314:
DLP-2 Logging in to the ATLAS 550 I
Page 315 and 316:
DLP-3 Setting IP Parameters for the
Page 317 and 318:
DLP-4 Verifying Communications Over
Page 319 and 320:
ATLAS 550 System Manual Section 5 D
Page 321 and 322:
DLP-5 Adding and Removing Users and
Page 323 and 324:
DLP-6 Updating the Firmware Using T
Page 325 and 326:
Page 327 and 328:
DLP-7 Updating the Firmware Using X
Page 329 and 330:
Page 331 and 332:
DLP-8 Saving the Current Configurat
Page 333 and 334:
DLP-9 Loading a Configuration Using
Page 335 and 336:
DLP-10 Saving and Transferring a Cu
Page 337 and 338:
DLP-11 Loading a Configuration Usin
Page 339 and 340:
DLP-12 Connecting the ATLAS 550 to
Page 341 and 342:
DLP-13 Using the ADTRAN Utility Sys
Page 343 and 344:
Page 345 and 346:
DLP-14 Connecting the Alarm Contact
Page 347 and 348:
Page 349 and 350:
DLP-15 Using the Alarm Connections
Page 351 and 352:
CONFIGURATION GUIDES CFG-1 Dial Bac
Page 353 and 354:
CFG-1 Dial Backup for Dedicated T1
Page 355 and 356:
ATLAS 550 System Manual Section 7,
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
SYSTEM EVENT LOGGING Explains the S
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
ADTRAN UTILITIES Provides instructi
Page 381 and 382:
ATLAS 550 System Manual Section 8 A
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
MIBS Provides a listing of SNMP Man
Page 391 and 392:
ATLAS 550 System Manual Section 9 M
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
show all

ATLAS 550 System Manual - Adtran

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?