ATLAS 550 System Manual - Adtran

More documents

Recommendations

Info

Section 4 User Interface Guide ATLAS 550 System Manual DIAL PLAN > USER TERM > IN#ACCEPT > SEARCH Write security: 3; Read security: 5 Instructs ATLAS 550 in which order to search for an accept number match. Normally, all searches are set to primary. The secondary search selection forces ATLAS 550 to only accept a call at this endpoint if all primary endpoints are unavailable. PRIMARY SEARCH All long distance calls should go out a PRI directly to an IXC (MCI, ATT, etc.), and local calls should go out a T1 to the LEC. It may be desirable to place long distance calls on the local exchange if all of the IXC trunks are unavailable (busy or in alarm). In this case, the primary accept number for the local exchange would be N$, and the secondary accept would be 1$. SECONDARY SEARCH The same accept rules apply for all secondary number searches as for primary searches. DIAL PLAN > USER TERM > IN#ACCEPT > DATA 64K, DATA 56K, AUDIO, SPEECH Write security: 3; Read security: 5 Reflects the bearer capability of the attached user equipment (typically a TA). If the attached TA can only handle digital calls, then a voice call sent to this endpoint would be rejected. DIAL PLAN > USER TERM > IN#ACCEPT > TREAT CALL AS Write security: 3; Read security: 5 Allows the incoming call to be treated as the selected call type, regardless of the actual incoming call type. The default selection, AS RECEIVED, effectively disables the feature by using the actual call type. Other options include DATA 64K and DATA 56K. DIAL PLAN > USER TERM > OUT#REJ Write security: 3; Read security: 5 Defines the parameters for the outgoing calls that ATLAS 550 will not send to the network. DIAL PLAN > USER TERM > OUT#REJ > REJECT NUMBER Identifies which numbers this endpoint will not pass on toward the network. Use when the outgoing call filter is different for different users sharing this endpoint. The wildcards are identical as in OUT#ACCEPT (see Dial Plan > Network Term > Out#Accept on page 251). [0,1]-$ rejects all long distance calls, but only for this User termination. If permitted in the Network termination endpoint, this user could not dial long distance numbers while other users could. DIAL PLAN > USER TERM > OUT#REJ > DATA 64K, DATA 56K, AUDIO, SPEECH Rejects outgoing calls based on call type. For example, setting the reject number to $, Digital 56/64 to ENABLED, and Audio and Speech to DISABLED, rejects all digital calls while not rejecting analog calls. This list may remain blank if the accept list meets desired filtering. 256 © 2004 ADTRAN, Inc. 61200305L2-1B
ATLAS 550 System Manual Section 4 User Interface Guide DIAL PLAN > USER TERM > IFCE CONFIG Write security: 3; Read security: 5 Specifies the configuration parameters for the endpoint.The selections displayed in this field are based on the type of module selected in the SLOT/SVC option. For detailed information on submenus for a particular module type, please refer to the dial plan interface configuration menu discussion for the appropriate network, option, or resource module. Some of the options available in this submenu change depending on the type of modules selected in the SLOT/SVC or PORT/PEP fields. For more information on these submenus, refer to the individual module interface configuration menu discussions in this section. DIAL PLAN > USER TERM > SUBST TEMPL Write security: 3; Read security: 5 The substitution template allows the ATLAS 550 to select calls (based on telephone number) and substitute a user-defined number for the received digits after the call has been processed by the switchboard. Substitution templates are created for each entry in the DIAL PLAN. DIAL PLAN > USER TERM > SUBST TEMPL > ORIGINAL# Write security: 3; Read security: 5 Designates the number(s) to be the search criteria for the substitution template. The pattern can be a specific number, or wildcards can be used as part of the number specification. X = Any single digit N = Any single digit 2 through 9 $ = Any number of digits of any value 9 = This specific number [1,2,3...] = A single digit in this group Example: 963-812[012] would be 963-8120 to 963-8122. DIAL PLAN > USER TERM > SUBST TEMPL > SUBSTITUTED# Write security: 3; Read security: 5 Designates the number to be substituted for the number(s) defined in the ORIGINAL# field. The pattern can be a specific number, or wildcards can be used as a part of the number specification. X = Any single digit N = Any single digit 2 through 9 $ = Any number of digits of any value 9 = This specific number [1,2,3...] = A single digit in this group Punctuation characters ( ) - + are ignored and a comma is interpreted as a .5 second pause in the dial string. 61200305L2-1B © 2004 ADTRAN, Inc. 257
Page 1 and 2:
61200305L2-1B August 2004 ATLAS 550
Page 3 and 4:
ATLAS 550 System Manual Revision Hi
Page 5 and 6:
ATLAS 550 System Manual Compliance
Page 7 and 8:
ATLAS 550 System Manual Industry Ca
Page 9 and 10:
ATLAS 550 System Manual Affidavit f
Page 11 and 12:
ATLAS 550 System Manual Warranty an
Page 13 and 14:
ATLAS 550 System Manual Customer Se
Page 15 and 16:
Table of Contents Section 1 System
Page 17 and 18:
SYSTEM DESCRIPTION Provides an over
Page 19 and 20:
ATLAS 550 System Manual Section 1 S
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
ENGINEERING GUIDELINES Provides equ
Page 27 and 28:
ATLAS 550 System Manual Section 2 E
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
NETWORK TURNUP PROCEDURE Provides s
Page 53 and 54:
ATLAS 550 System Manual Section 3 N
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
USER INTERFACE GUIDE Provides detai
Page 65 and 66:
ATLAS 550 System Manual Section 4 U
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206: ATLAS 550 System Manual Section 4 U
Page 255: ATLAS 550 System Manual Section 4 U
Page 307 and 308:
Page 309 and 310:
DETAIL LEVEL PROCEDURES DLP-1 Conne
Page 311 and 312:
DLP-1 Connecting a VT100 Terminal o
Page 313 and 314:
DLP-2 Logging in to the ATLAS 550 I
Page 315 and 316:
DLP-3 Setting IP Parameters for the
Page 317 and 318:
DLP-4 Verifying Communications Over
Page 319 and 320:
ATLAS 550 System Manual Section 5 D
Page 321 and 322:
DLP-5 Adding and Removing Users and
Page 323 and 324:
DLP-6 Updating the Firmware Using T
Page 325 and 326:
Page 327 and 328:
DLP-7 Updating the Firmware Using X
Page 329 and 330:
Page 331 and 332:
DLP-8 Saving the Current Configurat
Page 333 and 334:
DLP-9 Loading a Configuration Using
Page 335 and 336:
DLP-10 Saving and Transferring a Cu
Page 337 and 338:
DLP-11 Loading a Configuration Usin
Page 339 and 340:
DLP-12 Connecting the ATLAS 550 to
Page 341 and 342:
DLP-13 Using the ADTRAN Utility Sys
Page 343 and 344:
Page 345 and 346:
DLP-14 Connecting the Alarm Contact
Page 347 and 348:
Page 349 and 350:
DLP-15 Using the Alarm Connections
Page 351 and 352:
CONFIGURATION GUIDES CFG-1 Dial Bac
Page 353 and 354:
CFG-1 Dial Backup for Dedicated T1
Page 355 and 356:
ATLAS 550 System Manual Section 7,
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
SYSTEM EVENT LOGGING Explains the S
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
ADTRAN UTILITIES Provides instructi
Page 381 and 382:
ATLAS 550 System Manual Section 8 A
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
MIBS Provides a listing of SNMP Man
Page 391 and 392:
ATLAS 550 System Manual Section 9 M
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
show all

ATLAS 550 System Manual - Adtran

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?