ATLAS 550 System Manual - Adtran

More documents

Recommendations

Info

Section 4 User Interface Guide ATLAS 550 System Manual DIAL PLAN (E1/PRA) > NETWORK TERM (PRA) > IFCE CONFIG (PRA) > SWAP ANI/DNIS Write security: 3; Read security: 5 Swaps the ANI and DNIS numbers received from the network. ANI (Automatic Number Identification) is the billing number of the calling party, and DNIS (Dialed Number Identification Service) is the called party number. DIAL PLAN (E1/PRA) > NETWORK TERM (PRA) > IFCE CONFIG (PRA) > B CHANNEL SELECTION Write security: 3; Read security: 5 Determines how the ATLAS 550 switchboard uses B channels for call routing. The Circular method can be used for call load balancing among the available B channels on this interface. DIAL PLAN (E1/PRA) > USER TERM (PRA) Write security: 3; Read security: 5 This menu allows the user to define option parameters for ports which emulate a PRA connection. DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) Write security: 3; Read security: 5 Specifies the configuration parameters for the endpoint. DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > SWITCH TYPE Write security: 3; Read security: 5 Defines the type of PRA switch that the ATLAS 550 emulates. If connected to another ATLAS 550, both need to be set to the same switch type. The following option is available: • ETSI/DSS1 With this swap, the ATLAS 550 switchboard uses ANI to route the call. The accept number in the dial plan must use the ANI number, not the DNIS number. NORMAL Always start with the last channel configured (i.e., for a full PRI channel 23 would be used if available). CIRCULAR Contiguous channels from last to first. DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > FIRST DS0 Write security: 3; Read security: 5 Defines the first DS0 for this endpoint.The ATLAS 550 uses DS0s, starting with this selection, to send and receive calls to and from the network. The outgoing calls which are allowed or restricted over these DS0s are set by OUT#ACCEPT (see Dial Plan > Network Term > Out#Accept on page 251) and OUT#REJECT (see Dial Plan > Network Term > Out#Rej on page 252). DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > NUMBER OF DS0S Write security: 3; Read security: 5 Specifies the number of DS0s ATLAS 550 uses for this endpoint. 276 © 2004 ADTRAN, Inc. 61200305L2-1B
ATLAS 550 System Manual Section 4 User Interface Guide DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > STRIP MSD Write security: 3; Read security: 5 Strips a selected quantity (choose from NONE, 1, 2, and 3) of the most significant digits (MSD) of a dialed number prior to being forwarded out of the port. Example: A network port could be set to accept all calls beginning with 9 (9$), and then with STRIP MSD set to 1, all digits would be sent toward the network except the leading 9. STRIP MSD does not affect CALL ACCEPT criteria. All of the digits (including the MSDs that are subsequently stripped) are used as accept criterion. DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > NETWORK SPECIFIC FACILITY VOICE AND DATA Write security: 3; Read security: 5 Enables the sending of appropriate information to the PSTN. Currently not supported for E1/PRA use. DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > CALLED DIGITS TRANSFERRED Write security: 3; Read security: 5 Defines the number of digits to forward from the called number. When attached to a PBX, the PBX may be provisioned to expect to receive fewer than all of the called digits of the incoming call; however, this option would normally be set to ALL. Choose from NONE, THREE, FOUR, SEVEN, or ALL. DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > OUTGOING CALLER ID Write security: 3; Read security: 5 Defines the number to use to provide Caller ID to the network for outgoing calls sent through this endpoint. Choose from SEND AS PROVIDED, SUBSTITUTE IF NOT PRESENT, or SUBSTITUTE ALWAYS. The Caller ID number must be specific (i.e., no wildcards). DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > SOURCE ID Write security: 3; Read security: 5 Simplifies the creation of a dial plan in applications where the criterion for switching calls to a certain endpoint is a function of which endpoint originated the call. DEFAULT VALUE = 0. Zero is the default ID for all endpoints and all accept numbers. With default values, all calls are routed based only on the dialed number. Multiple endpoints can have the same SOURCE ID. When creating the CALL ACCEPT list, specify a SOURCE ID(s) as well as a dialed number or range of dialed numbers to accept. Example: An application requires that all calls that originate from Port 1 of the ATLAS 550 in Slot 1 be switched to Port 2 of that same module. Assign a unique SOURCE ID (e.g., 7) to Port 1 of the module, and then configure Port 2 to only accept calls from that unique SOURCE ID (7). 61200305L2-1B © 2004 ADTRAN, Inc. 277
Page 1 and 2:
61200305L2-1B August 2004 ATLAS 550
Page 3 and 4:
ATLAS 550 System Manual Revision Hi
Page 5 and 6:
ATLAS 550 System Manual Compliance
Page 7 and 8:
ATLAS 550 System Manual Industry Ca
Page 9 and 10:
ATLAS 550 System Manual Affidavit f
Page 11 and 12:
ATLAS 550 System Manual Warranty an
Page 13 and 14:
ATLAS 550 System Manual Customer Se
Page 15 and 16:
Table of Contents Section 1 System
Page 17 and 18:
SYSTEM DESCRIPTION Provides an over
Page 19 and 20:
ATLAS 550 System Manual Section 1 S
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
ENGINEERING GUIDELINES Provides equ
Page 27 and 28:
ATLAS 550 System Manual Section 2 E
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
NETWORK TURNUP PROCEDURE Provides s
Page 53 and 54:
ATLAS 550 System Manual Section 3 N
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
USER INTERFACE GUIDE Provides detai
Page 65 and 66:
ATLAS 550 System Manual Section 4 U
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226: ATLAS 550 System Manual Section 4 U
Page 275: ATLAS 550 System Manual Section 4 U
Page 309 and 310: DETAIL LEVEL PROCEDURES DLP-1 Conne
Page 311 and 312: DLP-1 Connecting a VT100 Terminal o
Page 313 and 314: DLP-2 Logging in to the ATLAS 550 I
Page 315 and 316: DLP-3 Setting IP Parameters for the
Page 317 and 318: DLP-4 Verifying Communications Over
Page 319 and 320: ATLAS 550 System Manual Section 5 D
Page 321 and 322: DLP-5 Adding and Removing Users and
Page 323 and 324: DLP-6 Updating the Firmware Using T
Page 325 and 326: ATLAS 550 System Manual Section 5 D
Page 327 and 328:
DLP-7 Updating the Firmware Using X
Page 329 and 330:
ATLAS 550 System Manual Section 5 D
Page 331 and 332:
DLP-8 Saving the Current Configurat
Page 333 and 334:
DLP-9 Loading a Configuration Using
Page 335 and 336:
DLP-10 Saving and Transferring a Cu
Page 337 and 338:
DLP-11 Loading a Configuration Usin
Page 339 and 340:
DLP-12 Connecting the ATLAS 550 to
Page 341 and 342:
DLP-13 Using the ADTRAN Utility Sys
Page 343 and 344:
Page 345 and 346:
DLP-14 Connecting the Alarm Contact
Page 347 and 348:
Page 349 and 350:
DLP-15 Using the Alarm Connections
Page 351 and 352:
CONFIGURATION GUIDES CFG-1 Dial Bac
Page 353 and 354:
CFG-1 Dial Backup for Dedicated T1
Page 355 and 356:
ATLAS 550 System Manual Section 7,
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
SYSTEM EVENT LOGGING Explains the S
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
ADTRAN UTILITIES Provides instructi
Page 381 and 382:
ATLAS 550 System Manual Section 8 A
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
MIBS Provides a listing of SNMP Man
Page 391 and 392:
ATLAS 550 System Manual Section 9 M
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
show all

ATLAS 550 System Manual - Adtran

Create successful ePaper yourself

Delete template?

Save as template?