ATLAS 550 System Manual - Adtran

More documents

Recommendations

Info

Section 5 DLP-14 ATLAS 550 System Manual Perform the following steps below in the order listed: 1. For the alarm relay contacts labeled ALARM, determine whether the external alarm reporting device uses a normally open (NO) or normally closed (NC) circuit for alarm relay (see pinout in Table 1). The ATLAS 550 external monitor labeled RELAY MON uses an NO circuit for alarm relay (see pinout in Table 2). 2. Using standard telco cross-connect wire, determine and cut the length required to reach from the alarm headers to the alarm-reporting device(s). 3. Using wire strippers, strip 1 inch from both ends of each wire. 4. If you want the ATLAS 550 to monitor for external alarms, remove both terminal blocks; otherwise, only remove the 4-position terminal block (ALARM). 5. Using the small straight slot screwdriver, loosen the screws in the terminal block(s). 6. For the 4-position terminal block (ALARM), insert one strand into the third slot (counted from the left) for the COM connection from the ATLAS 550. 7. Insert another strand into either the first slot or the second slot for the NC or NO connections, respectively. 8. (Optional) If you wish to have the ATLAS 550 monitor for external alarms, insert one strand of wire into the first slot (counted from the left) for the Alarm Out signal of the 2-position terminal block (RELAY). Insert the other strand into the last slot for the Alarm In signal. 9. Connect the wires to the appropriate terminals on the external device(s) being used. ALL EMPTY SLOTS MUST BE COVERED WITH BLANK PANELS 1 2 NETWORK 1 Table 1. Alarm Relay Connector Pinout Pin Name Description 1 Normally Closed (NC) Opens when a selected alarm condition is present. 2 Normally Open (NO) Closes when a selected alarm condition is present. 3 Common (COM) Common connection between external circuitry and NC or NO terminal. 4 Chassis Ground (GND) 500 Series 500 Series 500 Series 3 4 O I 346 © 2004 ADTRAN, Inc. 61200305L2-1B NETWORK 2 500 Series 500 Series 500 Series ADMIN External Alarm Relay Monitor Connection 90-240VAC, 2A 50/60Hz FUSE RATING: 2A/250V SLO-BLO ETHERNET RELAY ALARM MON NC NO COM Alarm Relay Connection CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE.
ATLAS 550 System Manual Section 5 DLP-14 Table 2. External Relay Monitor Connector Pinout Pin Name Description 1 Alarm Out Outputs EIA-232 level signal for connection to external alarm contacts. 2 Alarm In Monitors signal coming from external alarm contacts. 61200305L2-1B © 2004 ADTRAN, Inc. 347
Page 1 and 2:
61200305L2-1B August 2004 ATLAS 550
Page 3 and 4:
ATLAS 550 System Manual Revision Hi
Page 5 and 6:
ATLAS 550 System Manual Compliance
Page 7 and 8:
ATLAS 550 System Manual Industry Ca
Page 9 and 10:
ATLAS 550 System Manual Affidavit f
Page 11 and 12:
ATLAS 550 System Manual Warranty an
Page 13 and 14:
ATLAS 550 System Manual Customer Se
Page 15 and 16:
Table of Contents Section 1 System
Page 17 and 18:
SYSTEM DESCRIPTION Provides an over
Page 19 and 20:
ATLAS 550 System Manual Section 1 S
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
ENGINEERING GUIDELINES Provides equ
Page 27 and 28:
ATLAS 550 System Manual Section 2 E
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
NETWORK TURNUP PROCEDURE Provides s
Page 53 and 54:
ATLAS 550 System Manual Section 3 N
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
USER INTERFACE GUIDE Provides detai
Page 65 and 66:
ATLAS 550 System Manual Section 4 U
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296: ATLAS 550 System Manual Section 4 U
Page 309 and 310: DETAIL LEVEL PROCEDURES DLP-1 Conne
Page 311 and 312: DLP-1 Connecting a VT100 Terminal o
Page 313 and 314: DLP-2 Logging in to the ATLAS 550 I
Page 315 and 316: DLP-3 Setting IP Parameters for the
Page 317 and 318: DLP-4 Verifying Communications Over
Page 319 and 320: ATLAS 550 System Manual Section 5 D
Page 321 and 322: DLP-5 Adding and Removing Users and
Page 323 and 324: DLP-6 Updating the Firmware Using T
Page 327 and 328: DLP-7 Updating the Firmware Using X
Page 331 and 332: DLP-8 Saving the Current Configurat
Page 333 and 334: DLP-9 Loading a Configuration Using
Page 335 and 336: DLP-10 Saving and Transferring a Cu
Page 337 and 338: DLP-11 Loading a Configuration Usin
Page 339 and 340: DLP-12 Connecting the ATLAS 550 to
Page 341 and 342: DLP-13 Using the ADTRAN Utility Sys
Page 345: DLP-14 Connecting the Alarm Contact
Page 349 and 350: DLP-15 Using the Alarm Connections
Page 351 and 352: CONFIGURATION GUIDES CFG-1 Dial Bac
Page 353 and 354: CFG-1 Dial Backup for Dedicated T1
Page 355 and 356: ATLAS 550 System Manual Section 7,
Page 365 and 366: SYSTEM EVENT LOGGING Explains the S
Page 367 and 368: ATLAS 550 System Manual Section 7 S
Page 379 and 380: ADTRAN UTILITIES Provides instructi
Page 381 and 382: ATLAS 550 System Manual Section 8 A
Page 389 and 390: MIBS Provides a listing of SNMP Man
Page 391 and 392: ATLAS 550 System Manual Section 9 M
Page 397 and 398:
ATLAS 550 System Manual Section 9 M
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
show all

ATLAS 550 System Manual - Adtran

Create successful ePaper yourself

Delete template?

Save as template?