Brocade MLX Series and Brocade NetIron XMR Hardware ...

More documents

Recommendations

Info

4Installing a Brocade NetIron XMR 32000 routerUsing the insertion or extraction toolDue to the high density of cables that the Brocade NetIron XMR 32000 router can support, it maybe difficult to insert and remove the RJ45 and optical connectors. An insertion or extraction toolhas been provided in the Brocade NetIron XMR 32000 accessory kit to make this task easier. Referto Figure 194.FIGURE 194Insertion or extraction Tool211 Hooked tab 2 Stepped tabUse the tool to grasp the boot or the plug of the modular connector at the narrow end (the endclosest to the attached cable), and insert the connector into the proper interface module. Graspingthe boot or plug at the wide end during insertion may cause the tool to be difficult to release andremove.When using the tool to extract the boot or plug of a modular connector, cover the entire length ofthe boot or plug with the tool. Notice that one end of the tool has a “hook” side. Use this side tocompress the locking tab while you remove the connector.Brocade NetIron XMR 32000 cable managementBrocade NetIron XMR 32000 cable management is designed to ensure access to the powersupplies at the bottom of the router, and to keep the air inlet clear in the center of the router (this isessential for proper cooling). Cable management hardware at the top, bottom and sides of therouter help you route the cables in the proper direction.In general, cables from the outer interface modules are routed horizontally and away from therouter. Cables from the remaining modules in the upper half of the router are routed up, thenoutwards along the channels.The modules in the lower half of the router are routed downwards, above the power supplies.Figure 195 shows the cable routing, with the upper and lower cable management covers removedfor clarity.Cable management notesThe following rules apply when setting up cable management for a heavily- or fully-loaded system:• All cables must be firmly connected, supported, and contained.• Use cable cinches, spaced approximately every 24 inches, to secure all of the cables for eachmodule into a single bundle. This is especially important at the ends nearest the moduleconnections. Each cable cinch holds up to 8 MRJ21 cables, or 48 RJ45 cables.280 Brocade MLX Series and NetIron XMR Hardware Installation Guide53-1002373-02
Installing a Brocade NetIron XMR 32000 router 4• For additional security, use cable ties to secure cables to the cable management systemhardware on the sides of the unit (Refer to Figure 1.8).• The cable routing slots at the top and bottom of the unit are strong enough to hold manycables, but the more cable cinches and cable ties you use, the more secure your cablemanagement system will be.• If you bundle the cables correctly, you will be able to move the bundles to the side to accessthe modules for service, without disturbing the connections. Refer to Figure 204.• Always route the cables for the outer-most modules out the sides of the unit. Route the cablesfor the innermost modules through the top or through the bottom cable management hardwareon the unit.FIGURE 195:Brocade NetIron XMR 32000 cable routing schemeCAUTIONBe sure not to exceed the minimum recommended bend radius for the cables: 2 in. for MRJ-21cables, and 1.5 in. for Category 5 (RJ45) and fiber-optic cables.Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 28153-1002373-02
Page 1 and 2:
53-1002373-0226 September 2011®Bro
Page 3 and 4:
ContentsAbout This DocumentAudience
Page 5 and 6:
Installing a Brocade MLXe-32 router
Page 9 and 10:
Managing the cooling system. . . .
Page 11 and 12:
Dangers . . . . . . . . . . . . . .
Page 13 and 14:
About This DocumentAudienceThis doc
Page 15 and 16:
Document conventionsDocument conven
Page 17 and 18:
Document conventionsGetting technic
Page 19 and 20:
Product OverviewChapter1Brocade rou
Page 21 and 22:
Hardware features 1Brocade MLXe-8 r
Page 23 and 24:
Hardware features 1Figure 3 display
Page 25 and 26:
AC OKDC OKALMAC OKDC OKALMAC OKDC O
Page 27 and 28:
Hardware features 1Brocade MLX-8 ro
Page 29 and 30:
Hardware features 1Brocade MLX-32 r
Page 31 and 32:
Hardware features 1Brocade NetIron
Page 33 and 34:
Hardware features 1Brocade NetIron
Page 35 and 36:
Router modules 11-32 Interface slot
Page 37 and 38:
Router modules 1Figure 14 shows the
Page 39 and 40:
Router modules 1Management module L
Page 41 and 42:
Router modules 1TABLE 3 Interface m
Page 43 and 44:
Router modules 1Before you install
Page 45 and 46:
Router modules 1TABLE 6Router typeP
Page 47 and 48:
Router modules 1Gen-1 10Gx2 and 10G
Page 49 and 50:
Router modules 1Power supply requir
Page 51 and 52:
Router modules 1For an up to date l
Page 53 and 54:
Router modules 1FIGURE 20Port RX an
Page 55 and 56:
Router modules 1NOTEWhen you instal
Page 57 and 58:
Router modules 1NOTEWhen you are re
Page 59 and 60:
Router modules 1The front panel inc
Page 61 and 62:
Router modules 1Power supply requir
Page 63 and 64:
Router modules 1NOTEAll POS modules
Page 65 and 66:
Router modules 1POS module LEDsPOS
Page 67 and 68:
lRouter modules 1TABLE 23Part numbe
Page 69 and 70:
Router modules 1• 8-slot router:
Page 71 and 72:
Router modules 1• 32-slot router:
Page 73 and 74:
Router modules 1FIGURE 35Rear fan l
Page 75 and 76:
Router modules 1The fan control mod
Page 77 and 78:
Router modules 1FIGURE 39Front fan
Page 79 and 80:
Supported software features 1The 32
Page 81 and 82:
Installing a Brocade MLXe RouterCha
Page 83 and 84:
Installation precautions 2Power pre
Page 85 and 86:
Installing 2x100GbE interface modul
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Mounting Brocade MLXe-4, -8, or -16
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Activating the power source 2• Fo
Page 161 and 162:
Verifying proper operation 2TABLE 3
Page 163 and 164:
Verifying proper operation 2TABLE 3
Page 165 and 166:
Installing a Brocade MLX RouterChap
Page 167 and 168:
Installation precautions 3Power pre
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Installing a Brocade MLX-4 router 3
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Installing a Brocade MLX-16 router
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Attaching a management station 3Rem
Page 247 and 248: Verifying proper operation 3Insert
Page 249 and 250: Verifying proper operation 3TABLE 3
Page 251 and 252: Verifying proper operation 3Brocade
Page 253 and 254: Installing a Brocade NetIron XMR Ro
Page 255 and 256: Installation precautions 4CAUTIONUs
Page 257 and 258: Installing 2x100GbE interface modul
Page 259 and 260: Installing 2x100GbE interface modul
Page 261 and 262: Installing a Brocade NetIron XMR 40
Page 297: Installing a Brocade NetIron XMR 32
Page 315 and 316: Activating the power source 4Attach
Page 321 and 322: Using Brocade Structured Cabling Co
Page 323 and 324: mRJ21 procedures 5Cable cinch with
Page 325 and 326: RJ45 procedures 5Cable cinch with e
Page 327 and 328: RJ45 procedures 5Cable cinch with f
Page 329 and 330: RJ45 procedures 5Cable cinch with e
Page 331 and 332: Connecting a Router to a Network De
Page 333 and 334: Configuring IP addresses 6Support o
Page 335 and 336: Understanding management port funct
Page 337 and 338: Connecting the router to a network
Page 339 and 340: Managing Routers and ModulesChapter
Page 341 and 342: Managing the device 7• MUX index
Page 343 and 344: Managing the device 7To display thi
Page 345 and 346: Managing the device 7TABLE 46Fields
Page 347 and 348: Managing switch fabric modules 7Man
Page 349 and 350:
Managing the cooling system 7Managi
Page 351 and 352:
Managing the cooling system 7Table
Page 353 and 354:
Managing the cooling system 7Fan Sp
Page 355 and 356:
Managing the cooling system 7Displa
Page 357 and 358:
Managing interface modules 7If you
Page 359 and 360:
Managing interface modules 7Specify
Page 361 and 362:
Managing interface modules 7Syntax:
Page 363 and 364:
Enabling and disabling management m
Page 365 and 366:
Displaying management module CPU us
Page 367 and 368:
Maintenance and Field ReplacementCh
Page 369 and 370:
Replacing an interface module 8FIGU
Page 371 and 372:
Replacing a fiber-optic transceiver
Page 373 and 374:
Replacing a power supply 8NOTEA thr
Page 375 and 376:
Replacing a power supply 8running w
Page 377 and 378:
Replacing fan assemblies 87. For a
Page 379 and 380:
Replacing fan assemblies 8FIGURE 23
Page 381 and 382:
Page 383 and 384:
Replacing fan assemblies 8Replacing
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Replacing fan assemblies 85. Replac
Page 393 and 394:
Page 395 and 396:
Replacing fan assemblies 86. Place
Page 397 and 398:
Hardware SpecificationsChapter9This
Page 399 and 400:
Hardware specifications for Brocade
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Port specifications for all router
Page 411 and 412:
Power cords 9TABLE 68CountryPower c
Page 413 and 414:
Brocade MLXe Chassis bundlesAppendi
Page 415 and 416:
Brocade MLXe Chassis bundlesAPart n
Page 417 and 418:
Brocade MLXe Chassis bundlesATABLE
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Regulatory StatementsAppendixBU.S.A
Page 429 and 430:
Power cords (Japan Denan)BPower cor
Page 431 and 432:
BrazilBBrazilThe following Brocade
Page 433 and 434:
Caution and Danger NoticesAppendixC
Page 435 and 436:
CautionsCCAUTION For the DC input c
Page 437 and 438:
CautionsCCAUTIONFor the DC input ci
Page 439 and 440:
CautionsCCAUTIONVORSICHTMISE EN GAR
Page 441 and 442:
CautionsCCAUTIONVORSICHTRemoval of
Page 443 and 444:
CautionsCCAUTIONVORSICHTMISE EN GAR
Page 445 and 446:
DangersCDANGERGEFAHRDANGERPELIGRODi
Page 447 and 448:
DangersCDANGERAll fiber-optic inter
Page 449 and 450:
DangersCDANGERGEFAHRDANGERPELIGROTo
Page 451 and 452:
DangersCDANGERGEFAHRDANGERPELIGROTh
show all

Brocade MLX Series and Brocade NetIron XMR Hardware ...

Create successful ePaper yourself

Delete template?

Save as template?