Brocade MLX Series and Brocade NetIron XMR Hardware ...

More documents

Recommendations

Info

8Replacing a power supplyFIGURE 230Removing and replacing a power supply in a 32-slot device.23AC OKDC OKALMPwrActivePwrActive41PwrActivePwrActive5PwrActivePwrActivePwrActivePwrActive67891 Power supply indicators 6 Latch handle locked2 AC OK 7 Power supply blank cover3 DC OK 8 Pull down on plunger to remove4 ALM 9 Power supply5 Latch handle open4. Insert the new power supply into the empty power supply slot, using the guides provided oneither side of the slot.CAUTIONCarefully follow the mechanical guides on each side of the power supply slot and make sure thepower supply is properly inserted in the guides. Never insert the power supply upside down.5. After you insert the power supply, push gently on the power supply faceplate until the powersupply is fully seated.6. Pull up on the handle on the power supply faceplate to lock the power supply in place.358 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide53-1002373-02
Replacing fan assemblies 87. For a 4-slot device only, use the screwdriver to secure the two screws on either side of thepower supply faceplate.8. For a 2400W DC power supply only, crimp the #4 AWG power supply wire in the power lugs.9. For a 3000W DC power supply only, crimp the #2 AWG power supply wire in the power lugs.10. Connect the AC power cord or DC power lugs to the power supply faceplate.11. Connect the power to the AC or DC source.LEDs on the power supply faceplate show the status of the power supply with the following colors:• For a DC supply, the DC IN and DC OUT LEDs should be green, indicating the power supply isproviding power to the device components.• For an AC supply, the AC OK and DC OK LEDs should be green, indicating the power supply isproviding power to the device components (refer to Figure 230).• If the ALM LED is lit (amber), the power supply has failed.For information about troubleshooting this problem, refer to Table 39 on page 229.Replacing fan assembliesYou can replace a fan or a fan control module while the router is powered on and running. The fansand fan control modules are located on the rear panel of the router.NOTEFan trays are hot swappable. However, a hot-swap procedure should be completed within fiveminutes so the device will continue to function correctly without any fans. It is recommended thatyou disconnect the power supply from AC or DC power before installing or removing the fan tray.Replacing fan assemblies in all 32-slot routersThis section describes how to replace fan assemblies in MLXe, MLX, and XMR 32-slot routers.CAUTIONRemoving the rear fan modules on a 32-slot router provides access to bus bars and backplane.Avoid contact with these parts. There are hazardous energy levels at these locations.A 32-slot router has ten fan assemblies located at the rear of the router. They are numbered asindicated in Figure 231.You can remove and replace a fan assembly while the router is powered on and running.CAUTIONTo avoid overheating of the router, remove one fan assembly at a time, and replace it promptly.Wait for the LED on the fan assembly being replaced to turn green before replacing another fanassembly. Do not remove all fans from the device at once.Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 35953-1002373-02
Page 1 and 2:
53-1002373-0226 September 2011®Bro
Page 3 and 4:
ContentsAbout This DocumentAudience
Page 5 and 6:
Installing a Brocade MLXe-32 router
Page 9 and 10:
Managing the cooling system. . . .
Page 11 and 12:
Dangers . . . . . . . . . . . . . .
Page 13 and 14:
About This DocumentAudienceThis doc
Page 15 and 16:
Document conventionsDocument conven
Page 17 and 18:
Document conventionsGetting technic
Page 19 and 20:
Product OverviewChapter1Brocade rou
Page 21 and 22:
Hardware features 1Brocade MLXe-8 r
Page 23 and 24:
Hardware features 1Figure 3 display
Page 25 and 26:
AC OKDC OKALMAC OKDC OKALMAC OKDC O
Page 27 and 28:
Hardware features 1Brocade MLX-8 ro
Page 29 and 30:
Hardware features 1Brocade MLX-32 r
Page 31 and 32:
Hardware features 1Brocade NetIron
Page 33 and 34:
Hardware features 1Brocade NetIron
Page 35 and 36:
Router modules 11-32 Interface slot
Page 37 and 38:
Router modules 1Figure 14 shows the
Page 39 and 40:
Router modules 1Management module L
Page 41 and 42:
Router modules 1TABLE 3 Interface m
Page 43 and 44:
Router modules 1Before you install
Page 45 and 46:
Router modules 1TABLE 6Router typeP
Page 47 and 48:
Router modules 1Gen-1 10Gx2 and 10G
Page 49 and 50:
Router modules 1Power supply requir
Page 51 and 52:
Router modules 1For an up to date l
Page 53 and 54:
Router modules 1FIGURE 20Port RX an
Page 55 and 56:
Router modules 1NOTEWhen you instal
Page 57 and 58:
Router modules 1NOTEWhen you are re
Page 59 and 60:
Router modules 1The front panel inc
Page 61 and 62:
Router modules 1Power supply requir
Page 63 and 64:
Router modules 1NOTEAll POS modules
Page 65 and 66:
Router modules 1POS module LEDsPOS
Page 67 and 68:
lRouter modules 1TABLE 23Part numbe
Page 69 and 70:
Router modules 1• 8-slot router:
Page 71 and 72:
Router modules 1• 32-slot router:
Page 73 and 74:
Router modules 1FIGURE 35Rear fan l
Page 75 and 76:
Router modules 1The fan control mod
Page 77 and 78:
Router modules 1FIGURE 39Front fan
Page 79 and 80:
Supported software features 1The 32
Page 81 and 82:
Installing a Brocade MLXe RouterCha
Page 83 and 84:
Installation precautions 2Power pre
Page 85 and 86:
Installing 2x100GbE interface modul
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Mounting Brocade MLXe-4, -8, or -16
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Activating the power source 2• Fo
Page 161 and 162:
Verifying proper operation 2TABLE 3
Page 163 and 164:
Page 165 and 166:
Installing a Brocade MLX RouterChap
Page 167 and 168:
Installation precautions 3Power pre
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Installing a Brocade MLX-4 router 3
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Installing a Brocade MLX-16 router
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Attaching a management station 3Rem
Page 247 and 248:
Verifying proper operation 3Insert
Page 249 and 250:
Page 251 and 252:
Verifying proper operation 3Brocade
Page 253 and 254:
Installing a Brocade NetIron XMR Ro
Page 255 and 256:
Installation precautions 4CAUTIONUs
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Installing a Brocade NetIron XMR 40
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Activating the power source 4Attach
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Using Brocade Structured Cabling Co
Page 323 and 324:
mRJ21 procedures 5Cable cinch with
Page 325 and 326: RJ45 procedures 5Cable cinch with e
Page 327 and 328: RJ45 procedures 5Cable cinch with f
Page 329 and 330: RJ45 procedures 5Cable cinch with e
Page 331 and 332: Connecting a Router to a Network De
Page 333 and 334: Configuring IP addresses 6Support o
Page 335 and 336: Understanding management port funct
Page 337 and 338: Connecting the router to a network
Page 339 and 340: Managing Routers and ModulesChapter
Page 341 and 342: Managing the device 7• MUX index
Page 343 and 344: Managing the device 7To display thi
Page 345 and 346: Managing the device 7TABLE 46Fields
Page 347 and 348: Managing switch fabric modules 7Man
Page 349 and 350: Managing the cooling system 7Managi
Page 351 and 352: Managing the cooling system 7Table
Page 353 and 354: Managing the cooling system 7Fan Sp
Page 355 and 356: Managing the cooling system 7Displa
Page 357 and 358: Managing interface modules 7If you
Page 359 and 360: Managing interface modules 7Specify
Page 361 and 362: Managing interface modules 7Syntax:
Page 363 and 364: Enabling and disabling management m
Page 365 and 366: Displaying management module CPU us
Page 367 and 368: Maintenance and Field ReplacementCh
Page 369 and 370: Replacing an interface module 8FIGU
Page 371 and 372: Replacing a fiber-optic transceiver
Page 373 and 374: Replacing a power supply 8NOTEA thr
Page 375: Replacing a power supply 8running w
Page 379 and 380: Replacing fan assemblies 8FIGURE 23
Page 383 and 384: Replacing fan assemblies 8Replacing
Page 391 and 392: Replacing fan assemblies 85. Replac
Page 395 and 396: Replacing fan assemblies 86. Place
Page 397 and 398: Hardware SpecificationsChapter9This
Page 399 and 400: Hardware specifications for Brocade
Page 409 and 410: Port specifications for all router
Page 411 and 412: Power cords 9TABLE 68CountryPower c
Page 413 and 414: Brocade MLXe Chassis bundlesAppendi
Page 415 and 416: Brocade MLXe Chassis bundlesAPart n
Page 417 and 418: Brocade MLXe Chassis bundlesATABLE
Page 427 and 428:
Regulatory StatementsAppendixBU.S.A
Page 429 and 430:
Power cords (Japan Denan)BPower cor
Page 431 and 432:
BrazilBBrazilThe following Brocade
Page 433 and 434:
Caution and Danger NoticesAppendixC
Page 435 and 436:
CautionsCCAUTION For the DC input c
Page 437 and 438:
CautionsCCAUTIONFor the DC input ci
Page 439 and 440:
CautionsCCAUTIONVORSICHTMISE EN GAR
Page 441 and 442:
CautionsCCAUTIONVORSICHTRemoval of
Page 443 and 444:
CautionsCCAUTIONVORSICHTMISE EN GAR
Page 445 and 446:
DangersCDANGERGEFAHRDANGERPELIGRODi
Page 447 and 448:
DangersCDANGERAll fiber-optic inter
Page 449 and 450:
DangersCDANGERGEFAHRDANGERPELIGROTo
Page 451 and 452:
DangersCDANGERGEFAHRDANGERPELIGROTh
show all

Brocade MLX Series and Brocade NetIron XMR Hardware ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?