VisualDSP++ 4.5 Loader and Utilities Manual - Analog Devices

More documents

Recommendations

Info

ADSP-2106x/21160 Processor Loader Guide Table 3-15. ADSP-2106x/21160 Loader Command-Line Switches (Cont’d) Switch Description -v Outputs verbose loader utility messages and status information as the the utility processes files. -version Directs the loader utility to show its version information. Type elfloader -version to display the version of the loader drive. Add the -proc switch, for example, elfloader -proc ADSP-21062 -version to display version information of both loader drive and SHARC loader utility. Using VisualDSP++ Interface (Load Page) After selecting a Loader file as the target type on the Project page in VisualDSP++ Project Options dialog box, modify the default options on the Load: Processor page (also called loader property page). Click OK to save the selections. Selecting Build Project from the Project menu generates a loader file. For information relative to a specific processor, refer to the VisualDSP++ online help for that processor. VisualDSP++ invokes the elfloader utility to build the output file. The Load page buttons and fields correspond to loader command-line switches and parameters (see Table 3-15 on page 3-28). Use the Additional Options box to enter options that do not have dialog box equivalents. � For ADSP-21020 processors, the only permitted boot mode is JTAG: -bJTAG is automatically entered in the Additional Options box. 3-32 VisualDSP++ 4.5 Loader and Utilities Manual
4 LOADER FOR ADSP-21161 SHARC PROCESSORS This chapter explains how the loader utility (elfloader.exe) is used to convert executable (.dxe) files into boot-loadable files for ADSP-21161 SHARC processors. Refer to “Introduction” on page 1-1 for the loader utility overview; the introductory material applies to all processor families. Refer to “Loader for ADSP-2106x/21160 SHARC Processors” on page 3-1 for information about ADSP-21060, ADSP-21061, ADSP-21062, ADSP-21065L, and ADSP-21160 processors. Refer to “Loader for ADSP-2126x/2136x/2137x SHARC Processors” on page 5-1 for information about ADSP-2126x and ADSP-2136x processors. Loader operations specific to ADSP-21161 SHARC processors are detailed in the following sections. “ADSP-21161 Processor Booting” on page 4-2 Provides general information about various boot modes, including information about boot kernels. “ADSP-21161 Processor Loader Guide” on page 4-24 Provides reference information about the loader utility’s graphical user interface, command-line syntax, and switches. Refer to EE-177 SHARC SPI Booting, EE-199 Link Port Booting on the ADSP-21161 SHARC DSP, EE-209 Asynchronous Host Interface on the ADSP-21161 SHARC DSP on the Analog Devices Processor Web site for related information. VisualDSP++ 4.5 Loader and Utilities Manual 4-1
Page 1 and 2:
Analog Devices, Inc. One Technology
Page 3 and 4:
CONTENTS PREFACE Purpose of This Ma
Page 5 and 6:
CONTENTS Loader Files Without a Sec
Page 7 and 8:
CONTENTS ADSP-BF535 and ADSP-BF531/
Page 9 and 10:
Contents File Extensions ..........
Page 11 and 12:
Contents Boot Type Selection ......
Page 13 and 14:
PREFACE Thank you for purchasing Vi
Page 15 and 16:
Technical or Customer Support Prefa
Page 17 and 18:
ADSP-21367 ADSP-21368 ADSP21369 ADS
Page 19 and 20:
Preface VisualDSP++ 4.5 C/C++ Compi
Page 21 and 22:
VisualDSP++ Documentation Set Prefa
Page 23 and 24:
1 INTRODUCTION The majority of this
Page 25 and 26:
Loader Command Line Introduction If
Page 27 and 28:
Initialization Code Introduction In
Page 29 and 30:
A brief description of each phase f
Page 31 and 32:
Introduction Download the loadable
Page 33 and 34:
Introduction You can run the loader
Page 35 and 36:
PROM Boot Mode Introduction After r
Page 37 and 38:
Boot Streams Introduction The loade
Page 39 and 40:
2 LOADER/SPLITTER FOR BLACKFIN PROC
Page 41 and 42:
Loader/Splitter for Blackfin Proces
Page 43 and 44:
System Reset Configuration Register
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
D7 OUTPUT .LDR FILE 4-BYTE HEADER F
Page 51 and 52:
Page 53 and 54:
Second-Stage Loader Restrictions Lo
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
SPI Memory Detection Routine Loader
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
P0.H = HI(EBIU_SDRRC); R0 = 0x074A(
Page 79 and 80:
� Booting � SDRAM ADSP-BF536 pr
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
1-0-Byte Block Header Block Data Lo
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
� The Core B Loader/Splitter for
Page 95 and 96:
INITIALIZATION CODE (KERNEL WITH DE
Page 97 and 98:
Page 99 and 100:
FLASH MEMORY INIT CODE HEADER INIT
Page 101 and 102: where: � Command-line File Search
Page 103 and 104: Blackfin Loader Command-Line Switch
Page 105 and 106: Loader/Splitter for Blackfin Proces
Page 111 and 112: Using Base Loader Loader/Splitter f
Page 113 and 114: Table 2-11. Base Load Page Settings
Page 115 and 116: Using Second-Stage Loader Loader/Sp
Page 121 and 122: 3 LOADER FOR ADSP-2106X/21160 SHARC
Page 123 and 124: Loader for ADSP-2106x/21160 SHARC P
Page 125 and 126: Boot Mode Selection Loader for ADSP
Page 147 and 148: File Searches Loader for ADSP-2106x
Page 151: -si-revision #|none|any Loader for
Page 155 and 156: Loader for ADSP-21161 SHARC Process
Page 169 and 170: ADSP-21161 Processor Boot Streams L
Page 171 and 172: To Modify a Boot Kernel Source File
Page 175 and 176: Processor ID Numbers Loader for ADS
Page 179 and 180: File Searches Loader for ADSP-21161
Page 185 and 186: 5 LOADER FOR ADSP-2126X/2136X/2137X
Page 187 and 188: Loader for ADSP-2126x/2136x/2137x S
Page 203 and 204:
Loader for ADSP-2126x/2136x/2137x S
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
File Searches Loader for ADSP-2126x
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
6 LOADER FOR TIGERSHARC PROCESSORS
Page 237 and 238:
� EE-174: Loader for TigerSHARC P
Page 239 and 240:
Boot Kernel Modification Loader for
Page 241 and 242:
Loader for TigerSHARC Processors el
Page 243 and 244:
TigerSHARC Command-Line Switches Lo
Page 245 and 246:
Loader for TigerSHARC Processors Ta
Page 247 and 248:
7 SPLITTER FOR SHARC AND TIGERSHARC
Page 249 and 250:
� Most Splitter for SHARC and Tig
Page 251 and 252:
Splitter for SHARC and TigerSHARC P
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
A FILE FORMATS VisualDSP++ developm
Page 259 and 260:
Assembly Source Files File Formats
Page 261 and 262:
Build Files File Formats Build file
Page 263 and 264:
Memory Map Files File Formats The l
Page 265 and 266:
Table A-4. End-of-File Record Examp
Page 267 and 268:
This example shows how to include t
Page 269 and 270:
Table A-7. S1 Termination Record Ex
Page 271 and 272:
File Formats A block of data record
Page 273 and 274:
Table A-9. SPORT Data File Example
Page 275 and 276:
B UTILITIES The VisualDSP++ develop
Page 277 and 278:
elf2flt - ELF to BFLT File Converte
Page 279 and 280:
Table B-3. BFLT File Dumper Command
Page 281 and 282:
I INDEX Numerics -64 splitter switc
Page 283 and 284:
BMS pins ADSP-2106x/160 processors,
Page 285 and 286:
data initialization files (.dat), A
Page 287 and 288:
external memory (SHARC processors)
Page 289 and 290:
initialization blocks (Blackfin pro
Page 291 and 292:
loader file formats (ADSP-BF535 pro
Page 293 and 294:
P -p # loader switch for Blackfin,
Page 295 and 296:
shared memory Blackfin processors,
Page 297 and 298:
V .VAR directive, A-3 vector addres
show all

VisualDSP++ 4.5 Loader and Utilities Manual - Analog Devices

Create successful ePaper yourself

Delete template?

Save as template?