AT Commands Reference Manual - wireless netcontrol GmbH

More documents

Recommendations

Info

Hardware Information +MUANTYPE: 2 OK ATS97, Antenna Diagnostic This command indicates the status of the antenna physical connection to the H24 RF connector. This information is also provided by a dedicated hardware signal, which is output on pin 41 (ANT_DET) of the interface connector. Note: Before use ATS97 command, antenna type shall be determined. (see See “+MUANTYPE, Set the Type of Antenna Used”). Improper antenna type determination may cause wrong antenna status report. Three antenna types are supported: • Type 0: Infinite Impedance Type - IIT (Active resistance is > 3.1 MOhm). • Type 1: Medium Impedance Type - MIT ( 6.8 KOhm < Active resistance is < 3.1 MOhm). Medium Impedance type is divided into two subtypes: • Medium-Low Impedance antenna - MLI (< 310 Ohm approximately); • Medium-High Impedance antenna - MHI (> 310 Ohm approximately); • Type 2: Zero Impedance Type - ZIT (Active resistance is < 6.8 KOhm). Limitations 1. For Type 0: Only "Grounded" state is recognizable - Other states will be reported as a "Normal". 2. For Type 1: All statuses may be recognized. 3. For Type 2: Only "Disconnected" state is recognizable - Other states will be reported as a "Normal". These limitations refer to both: ANT_DET pin state and response to ATS97 command (see below). ANT_DET Pin 41 on 70 pin connector reflects antenna state. 1. When antenna state is "N" - Normal, ANT_DET pin is HIGH (2.6V). 2. When antenna state is "D" - Disconnected or "G" - Grounded, ANT_DET pin is LOW (0V). Report delaying ANT_DET report may be delayed by 4 sec max. Such a delay is relevant only for Medium Impedance Type - MIT (Type 1) and depending on both: antenna sub-type and status change. The cases of such a delay are signed by "delayed" in the table below. Antenna Type Change of State Delay of ANT_DET Pin LIA (Low impedance) N => D or D => N Immediate N => G or G => N D => G or G => D Delayed Immediate 3-192 H24 - AT Commands Reference Manual April 15, 2010
Chapter 3: AT Commands Reference Antenna Type Change of State Delay of ANT_DET Pin HIA (High Impedance) N => D or D => N Delayed N => G or G => N D => G or G => D Immediate Immediate Command Type Syntax Response/Action Remarks Execute ATS97 OK Deprecated; Implemented only for backward compatibility with older Motorola modules. Read ATS97? OK or: +CME ERROR: The Read command indicates antenna connection status. Note: When antenna type is unknown (factory default state), an error will be returned to read command. The following table shows the ATS97 parameters. Table 3-123: ATS97 Parameters Description 000 The antenna is not connected 001 The antenna is connected 002 The antenna is grounded Example // Connect the antenna ATS97? 001 ATS97 OK ATS97=? ERROR // Disconnect the antenna ATS97? 000 April 15, 2010 H24 - AT Commands Reference Manual 3-193
Page 1 and 2:
Technical Information Motorola H24
Page 3:
Trademarks MOTOROLA and the Stylize
Page 6 and 7:
Table of Contents Audio . . . . . .
Page 8 and 9:
Table of Contents Fax Commands . .
Page 10 and 11:
Table of Contents Standard Audio Co
Page 12 and 13:
Table of Contents User Plane Protoc
Page 14 and 15:
Table of Contents Serial Driver - C
Page 16 and 17:
List of Figures xii H24 - AT Comman
Page 18 and 19:
List of Tables 3-45 +CSMP Parameter
Page 20 and 21:
List of Tables 3-151 +MFOTAWSCFG Pa
Page 22 and 23:
List of Tables xviii H24 - AT Comma
Page 24 and 25:
Applicable Documents Applicable Doc
Page 26 and 27:
Caring for the Environment Keep awa
Page 28 and 29:
Warranty Notification Warranty Noti
Page 30 and 31:
Installed Data 2. Defects or damage
Page 32 and 33:
Revision History xxviii H24 - AT Co
Page 34 and 35:
Data Operation The following diagra
Page 36 and 37:
Data Operation Figure 1-3 shows a C
Page 38 and 39:
CSD Operation • +CGEQREQ - 3G Qua
Page 40 and 41:
Improved OEM Features Another high
Page 42 and 43:
Multi Channeling Multi Channeling O
Page 44 and 45:
Short Message Service (SMS) Short M
Page 46 and 47:
Device management OTA Device manage
Page 48 and 49:
Personalization Personalization Ove
Page 50 and 51:
A-GPS A-GPS Overview gpsOne technol
Page 52 and 53:
AT Commands Summary +CRC RING This
Page 54 and 55:
AT Commands Summary +CMGS This comm
Page 56 and 57:
AT Commands Summary &D +MCWAKE +CFU
Page 58 and 59:
AT Commands Summary Table 1-1: AT C
Page 60 and 61:
AT Commands Summary Table 1-1: AT C
Page 62 and 63:
AT Commands Summary +MGPSTTFF This
Page 64 and 65:
AT Commands Protocol General System
Page 66 and 67:
AT Commands Structure Results Code
Page 68 and 69:
Command Token Types Command Token T
Page 70 and 71:
Values Values Range of Values When
Page 72 and 73:
Modem ID +CGMM, +GMM, +FMM, Request
Page 74 and 75:
Modem ID The following table shows
Page 76 and 77:
Modem ID Example AT+CIMI +CIMI: 314
Page 78 and 79:
Modem ID OK +CLAC, List of All Avai
Page 80 and 81:
Call Control If the other modem doe
Page 82 and 83:
Call Control If a DATA/FAX call was
Page 84 and 85:
Call Control The format of ATD> com
Page 86 and 87:
Call Control The following table sh
Page 88 and 89:
Call Control NO CARRIER OK Example
Page 90 and 91:
Call Control AT+CRC=? +CRC: (0-1) O
Page 92 and 93:
Call Control AT+CRC=1 OK (…incomi
Page 94 and 95:
Call Control AT+CCWA? +CCWA: 1 OK E
Page 96 and 97:
Page 98 and 99:
Call Control NO CARRIER // BUSY app
Page 100 and 101:
Page 102 and 103:
Call Control • Not provisioned (C
Page 104 and 105:
Call Control Command Type Syntax Re
Page 106 and 107:
Call Control AT+MFIC? +MFIC: 0,"SM"
Page 108 and 109:
Call Control Table 3-17: +CBST Sett
Page 110 and 111:
Call Control The ESC command +++, t
Page 112 and 113:
Call Control +MVC, Motorola Vocoder
Page 114 and 115:
Call Control Assistant (CA) will ty
Page 116 and 117:
Call Control If there are no calls
Page 118 and 119:
Call Control +CSSN, Supplementary S
Page 120 and 121:
Call Control Table 3-26: +CSSU Noti
Page 122 and 123:
Call Control Table 3-27: +CUSD Para
Page 124 and 125:
Call Control Table 3-28: CUSD Termi
Page 126 and 127:
Page 128 and 129:
Fax Class 1 Fax Commands +FCLASS, S
Page 130 and 131:
Fax Class 1 The following table sho
Page 132 and 133:
Fax Class 1 +FRM, Receive Data This
Page 134 and 135:
Fax Class 1 +FRH, Receive DATA with
Page 136 and 137:
Phonebook and Clock The following t
Page 138 and 139:
Phonebook and Clock The following t
Page 140 and 141:
Phonebook and Clock AT+CPBF="Moto"
Page 142 and 143:
Phonebook and Clock System Date and
Page 144 and 145:
Phonebook and Clock +CCLK: "05/10/2
Page 146 and 147:
SMS The following table shows the +
Page 148 and 149:
SMS +CSCA: "*ABC#",129 // Read comm
Page 150 and 151:
SMS Note: • Incoming Status-Repor
Page 152 and 153:
SMS +CSMP, Set Text Mode Parameters
Page 154 and 155:
SMS +CSDH, Show Text Mode Parameter
Page 156 and 157:
SMS +CMGW, Write Message to Memory
Page 158 and 159:
SMS OK +CMSS, Send Message From Sto
Page 160 and 161:
SMS +CSMS, Select Message Service.
Page 162 and 163:
Page 164 and 165:
SMS In PDU mode, either positive (R
Page 166 and 167:
SMS Example AT+CPMS? +CPMS: "SM",3,
Page 168 and 169:
SMS Example AT+CNMI=1,,,2 // Set t
Page 170 and 171:
SMS +CMGR, +MMGR, Read Message Thes
Page 172 and 173:
SMS Table 3-60: +CMGR/+MMGR Paramet
Page 174 and 175:
SMS OK AT+CMGF=1 OK AT+CMGR=0 // Re
Page 176 and 177:
Page 178 and 179:
SMS than 0, the parameter is pract
Page 180 and 181:
SMS Command Type Syntax Response/Ac
Page 182 and 183:
SMS Notes: Example • A combinatio
Page 184 and 185:
SMS Table 3-66: Layout of SMS-DELIV
Page 186 and 187:
SMS Table 3-69: of SMS-COMMAND Mes
Page 188 and 189:
SMS Table 3-71: of SMS-STATUS-REPO
Page 190 and 191:
SMS DCS handling Sending or Storing
Page 192 and 193:
SMS ### Store in TEXT mode SMS enco
Page 194 and 195:
Page 196 and 197:
Network Network Network Commands +C
Page 198 and 199:
Network • GSM supports RLP Versio
Page 200 and 201:
Network +CGREG, GPRS Network Regist
Page 202 and 203:
Network +CGREG: 2, 1, A065, 988b OK
Page 204 and 205:
Network Notes: 1. The access techno
Page 206 and 207:
Network OK AT+COPS=3,2 AT+COPS? +CO
Page 208 and 209:
Network +CPOL, Preferred Operators
Page 210 and 211:
Network OK AT+CPOL? +CPOL: 000,000,
Page 212 and 213: Network The following table shows t
Page 214 and 215: Network OK //exec command AT+MBAND
Page 216 and 217: Network Table 3-88: +MCI Parameters
Page 218 and 219: Network "2G",631,,,1,,,,,, "2G",627
Page 220 and 221: Network +WS46, Get Wireless Network
Page 222 and 223: Network +MPDS: 1 OK AT+MPDS? +MPDS:
Page 224 and 225: Network The following table shows t
Page 226 and 227: Hardware Information Hardware Infor
Page 228 and 229: Hardware Information The following
Page 230 and 231: Hardware Information +IPR: (1-8,10-
Page 234 and 235: Hardware Information +MCWAKE, GPRS
Page 236 and 237: Hardware Information Setting report
Page 238 and 239: Hardware Information AT+CFUN? +CFUN
Page 240 and 241: Hardware Information Command Type S
Page 244 and 245: Hardware Information Table 3-105: G
Page 246 and 247: Hardware Information +MIOI, Motorol
Page 248 and 249: Hardware Information +MPCMC, Contin
Page 250 and 251: Hardware Information +MVREF, Motoro
Page 252 and 253: Hardware Information +MFTM: (0-1) O
Page 254 and 255: Hardware Information Table 3-113: +
Page 256 and 257: Hardware Information AT+TGFCC = 1,0
Page 264 and 265: Audio Audio General Audio Mode - Yo
Page 266 and 267: Audio +CLVL: 5 OK AT+CLVL=? +CLVL:
Page 268 and 269: Audio +CRTT, Ring Type Selection Th
Page 270 and 271: Audio OK AT+VTD? +VTD: 5 OK AT+VTD=
Page 272 and 273: Audio +MACSTG, Set CODEC ST Gain Se
Page 274 and 275: Audio The following table shows the
Page 276 and 277: Audio +MAGRST, Restore Default Gain
Page 278 and 279: Audio +MANS, Noise Suppression Cont
Page 280 and 281: Audio • FIR Filter • Automatic
Page 282 and 283: Access +CPIN, Enter PIN for Unlocki
Page 284 and 285: Access Table 3-143: +CPIN Parameter
Page 286 and 287: Access +EPIN, Enter SIM PIN2 to Ver
Page 288 and 289: Access Notes: 1. When SIM is not in
Page 290 and 291: Access +CPWD, Change Password This
Page 292 and 293: Access Command Type Syntax Response
Page 294 and 295: Access AT+CLCK="IR",2 +CLCK: 1,1 +C
Page 296 and 297: Access Example AT+MGSMSIM? +MGSMSIM
Page 298 and 299: Firmware Update Over the Air (FOTA)
Page 310 and 311: Modem Configuration and Profile The
Page 312 and 313:
Modem Configuration and Profile Exa
Page 314 and 315:
Modem Configuration and Profile Exa
Page 316 and 317:
Modem Configuration and Profile The
Page 318 and 319:
Page 320 and 321:
Modem Configuration and Profile Tab
Page 322 and 323:
Modem Configuration and Profile Sle
Page 324 and 325:
Modem Configuration and Profile Sle
Page 326 and 327:
Modem Configuration and Profile •
Page 328 and 329:
Modem Configuration and Profile Com
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
UI (User Interface) The following t
Page 344 and 345:
UI (User Interface) The following t
Page 346 and 347:
UI (User Interface) atd035681234; O
Page 348 and 349:
UI (User Interface) +MIND: (0-3),(0
Page 350 and 351:
UI (User Interface) Table 3-184: +M
Page 352 and 353:
UI (User Interface) Unsolicited Sta
Page 354 and 355:
UI (User Interface) Unsolicited Rep
Page 356 and 357:
GPRS/EDGE/UMTS +CGDCONT, Define PDP
Page 358 and 359:
GPRS/EDGE/UMTS at+cgdcont=3,"IP","s
Page 360 and 361:
GPRS/EDGE/UMTS The following table
Page 362 and 363:
GPRS/EDGE/UMTS Command Type Syntax
Page 364 and 365:
GPRS/EDGE/UMTS +CGQREQ, Quality of
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
GPRS/EDGE/UMTS 3G and EDGE Commands
Page 374 and 375:
Page 376 and 377:
GPRS/EDGE/UMTS Table 3-196: +CGEQRE
Page 378 and 379:
GPRS/EDGE/UMTS +CGEQMIN, 3G and EDG
Page 380 and 381:
Page 382 and 383:
GPRS/EDGE/UMTS Table 3-197: +CGEQMI
Page 384 and 385:
GPRS/EDGE/UMTS TCP/UDP IP Introduct
Page 386 and 387:
Page 388 and 389:
GPRS/EDGE/UMTS +MIPOPEN, Open a Soc
Page 390 and 391:
Page 392 and 393:
GPRS/EDGE/UMTS AT+MIPOPEN? +MIPOPEN
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
GPRS/EDGE/UMTS OK 3-332 H24 - AT Co
Page 404 and 405:
GPRS/EDGE/UMTS parameters before so
Page 406 and 407:
Page 408 and 409:
GPRS/EDGE/UMTS Example AT+MIPCONF =
Page 410 and 411:
GPRS/EDGE/UMTS +MIPRUDP, Socket Net
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
GPRS/EDGE/UMTS +MPINGSTAT, Status U
Page 418 and 419:
GPRS/EDGE/UMTS +MIPCSC, Motorola Co
Page 420 and 421:
GPRS/EDGE/UMTS Example AT+MIPCSC=?
Page 422 and 423:
GPRS/EDGE/UMTS Table 3-217: +MIPSSL
Page 424 and 425:
GPRS/EDGE/UMTS Table 3-219: Status
Page 426 and 427:
A-GPS Command Type Syntax Response/
Page 428 and 429:
A-GPS The following table shows the
Page 430 and 431:
A-GPS Using the read command H24 su
Page 432 and 433:
A-GPS Command Type Syntax Response/
Page 434 and 435:
A-GPS Example hot state. Once hot s
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
RS232 Multiplexer Feature RS232 Mul
Page 442 and 443:
RS232 Multiplexer Feature MUX State
Page 444 and 445:
RS232 Multiplexer Feature +CMUX, MU
Page 446 and 447:
Connectivity Configuration Connecti
Page 448 and 449:
Multi Channeling Multi Channeling M
Page 450 and 451:
Multi Channeling AT Commands per Ch
Page 452 and 453:
Multi Channeling +CLCK v +CLIP v v
Page 454 and 455:
Multi Channeling +CUSD v Unsolicite
Page 456 and 457:
Multi Channeling +MIPSETS v U +MIPS
Page 458 and 459:
Multi Channeling Table 3-237: Multi
Page 460 and 461:
Multi Channeling 3-390 H24 - AT Com
Page 462 and 463:
Recommended H24 Initialization afte
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
SMS SMS Managing Stored Messages in
Page 470 and 471:
SMS AT+CMGF=0 OK AT+CMGR=129 +CMGR:
Page 472 and 473:
Call Control Call Control The follo
Page 474 and 475:
Call Control atd>"ME"1117 +CME ERRO
Page 476 and 477:
Data Call Data Call Switching Modes
Page 478 and 479:
Packet Data Using the ATD* Command
Page 480 and 481:
Sleep Mode Sleep Mode Note: Note:Th
Page 482 and 483:
TCP/IP: MIP Commands Using Cases OK
Page 484 and 485:
TCP/IP: MIP Commands Using Cases +M
Page 486 and 487:
TCP/IP: MIP Commands Using Cases Ne
Page 488 and 489:
TCP/IP: MIP Commands Using Cases Af
Page 490 and 491:
TCP/IP: MIP Commands Using Cases OK
Page 492 and 493:
TCP/IP: MIP Commands Using Cases re
Page 494 and 495:
TCP/IP: MIP Commands Using Cases Fo
Page 496 and 497:
Firmware Update Over the Air (FOTA)
Page 498 and 499:
5-2 H24 - AT Commands Reference Man
Page 500 and 501:
AT Commands Alphabetical Summary +C
Page 502 and 503:
AT Commands Alphabetical Summary +C
Page 504 and 505:
AT Commands Alphabetical Summary +F
Page 506 and 507:
AT Commands Alphabetical Summary +M
Page 508 and 509:
AT Commands Alphabetical Summary +M
Page 510 and 511:
Character Set Table CS1: (GSM -> UC
Page 512 and 513:
Character Set Table CS1: (GSM -> UC
Page 514 and 515:
Character Set Table CS2: (GSM IRA)
Page 516 and 517:
Character Set Table CS2: (GSM IRA)
Page 518 and 519:
Character Set Table CS3: (UCS-2 Ful
Page 520 and 521:
Character Set Table CS4: (IRA table
Page 522 and 523:
Page 524 and 525:
Page 526 and 527:
USB Compositions 1. CDC/ACM Class i
Page 528 and 529:
ACM Driver - Modem Interface Select
Page 530 and 531:
Serial Driver - Control Interface A
Page 532 and 533:
USB Power Management Then, find you
Page 534 and 535:
D E F G C CTS D DA D DCD D DCE D DC
Page 536 and 537:
Abbreviation Full Name I L M O P I
Page 538 and 539:
Abbreviation Full Name T U V T TBD
Page 540 and 541:
B - B Index +CSSN, Supplementary Se
Page 542 and 543:
G - P Index Xon, 3-339 G GPRS Attac
Page 544 and 545:
V - W Index User Interface Commands
Page 546 and 547:
W - W Index April 15, 2010 H24 - AT
Page 548 and 549:
Page 550 and 551:
Page 552:
show all

AT Commands Reference Manual - wireless netcontrol GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?