AT Commands Reference Manual - wireless netcontrol GmbH

More documents

Recommendations

Info

Firmware Update Over the Air (FOTA) +MFOTAIND, Send Unsolicited FOTA Indications Toward the DTE When set, the module will send all the indications mentioned in Table 3-155. By default, FOTA unsolicited information report is Disabled. Command Type Syntax Response/Action Remarks Set AT+MFOTAIND= OK or: +CME ERROR: The Set command enables/disables Unsolicited indications. See Table 3-155. Read AT+MFOTAIND? + MFOTAIND: < EN-ind >, OK Returns value. Test AT+FOTAIND=? + FOTAIND: (list of < EN-ind >s) Unsolicited Report +FOTAIND +FOTAIND: , OMA state and FOTA information reports during FOTA process. The following table shows the +MFOTIND parameters. Table 3-155: +MFOTAIND Parameters Description 0 - Disable FOTA unsolicited informational report. 1 - Enable FOTA unsolicited informational report. The default value is 0. Enables the Module to indicate the DTE with FOTA progress. Relevant to Non transparent mode. 3-234 H24 - AT Commands Reference Manual April 15, 2010
Chapter 3: AT Commands Reference Table 3-155: +MFOTAIND Parameters (Cont.) Description 10 Idle/Start - No pending operation. 20 Download Failed. 30 Download has started. 40 Download complete - Successfully. 50 Ready to Update - Have data and awaiting command to start update. 60 Update progressing - update has started. 70 Update Failed / Have Data - Update failed but have update package. 80 Update Failed / No Data - Update failed and no update package available. 90 Update Successful / Have Data - Update complete and data still available. 100 Update Successful / No Data - Data deleted or removed after a successful Update. 5 DM Session started. 6 DM session in progress. 7 DM Session completed. 8 xx DM session interrupted, xx (fail reason see Table 3-156). 9 Unable to connect to server. 10 Bootstrap completed. 11 Access failed. 12,xx Download failed, xx (fail reason see Table 3-156). 13,xx Software update xx% completed. 14 Download in progress. 15 SW download completed. 16 SW update complete. 17 SW update failed. 18 No update package available. 19 SW installation has started. The following table shows the failure reasons. Table 3-156: Failure Reasons Failure Reason 0 Success. 16 Unspecific error. 17 Memory error. 18 Not allowed or bad parameters. 19 Attempt to call TRG_RDM_run with non-resume trigger when suspended. 32 SyncML message Protocol or version error. 8194 Workspace buffer too small. 24576 Buffer overflow. 24577 Badly formatted input. 24578 Tree node already exists. 24579 Tree node is missing. April 15, 2010 H24 - AT Commands Reference Manual 3-235
Page 1 and 2:
Technical Information Motorola H24
Page 3:
Trademarks MOTOROLA and the Stylize
Page 6 and 7:
Table of Contents Audio . . . . . .
Page 8 and 9:
Table of Contents Fax Commands . .
Page 10 and 11:
Table of Contents Standard Audio Co
Page 12 and 13:
Table of Contents User Plane Protoc
Page 14 and 15:
Table of Contents Serial Driver - C
Page 16 and 17:
List of Figures xii H24 - AT Comman
Page 18 and 19:
List of Tables 3-45 +CSMP Parameter
Page 20 and 21:
List of Tables 3-151 +MFOTAWSCFG Pa
Page 22 and 23:
List of Tables xviii H24 - AT Comma
Page 24 and 25:
Applicable Documents Applicable Doc
Page 26 and 27:
Caring for the Environment Keep awa
Page 28 and 29:
Warranty Notification Warranty Noti
Page 30 and 31:
Installed Data 2. Defects or damage
Page 32 and 33:
Revision History xxviii H24 - AT Co
Page 34 and 35:
Data Operation The following diagra
Page 36 and 37:
Data Operation Figure 1-3 shows a C
Page 38 and 39:
CSD Operation • +CGEQREQ - 3G Qua
Page 40 and 41:
Improved OEM Features Another high
Page 42 and 43:
Multi Channeling Multi Channeling O
Page 44 and 45:
Short Message Service (SMS) Short M
Page 46 and 47:
Device management OTA Device manage
Page 48 and 49:
Personalization Personalization Ove
Page 50 and 51:
A-GPS A-GPS Overview gpsOne technol
Page 52 and 53:
AT Commands Summary +CRC RING This
Page 54 and 55:
AT Commands Summary +CMGS This comm
Page 56 and 57:
AT Commands Summary &D +MCWAKE +CFU
Page 58 and 59:
AT Commands Summary Table 1-1: AT C
Page 60 and 61:
AT Commands Summary Table 1-1: AT C
Page 62 and 63:
AT Commands Summary +MGPSTTFF This
Page 64 and 65:
AT Commands Protocol General System
Page 66 and 67:
AT Commands Structure Results Code
Page 68 and 69:
Command Token Types Command Token T
Page 70 and 71:
Values Values Range of Values When
Page 72 and 73:
Modem ID +CGMM, +GMM, +FMM, Request
Page 74 and 75:
Modem ID The following table shows
Page 76 and 77:
Modem ID Example AT+CIMI +CIMI: 314
Page 78 and 79:
Modem ID OK +CLAC, List of All Avai
Page 80 and 81:
Call Control If the other modem doe
Page 82 and 83:
Call Control If a DATA/FAX call was
Page 84 and 85:
Call Control The format of ATD> com
Page 86 and 87:
Call Control The following table sh
Page 88 and 89:
Call Control NO CARRIER OK Example
Page 90 and 91:
Call Control AT+CRC=? +CRC: (0-1) O
Page 92 and 93:
Call Control AT+CRC=1 OK (…incomi
Page 94 and 95:
Call Control AT+CCWA? +CCWA: 1 OK E
Page 96 and 97:
Page 98 and 99:
Call Control NO CARRIER // BUSY app
Page 100 and 101:
Page 102 and 103:
Call Control • Not provisioned (C
Page 104 and 105:
Call Control Command Type Syntax Re
Page 106 and 107:
Call Control AT+MFIC? +MFIC: 0,"SM"
Page 108 and 109:
Call Control Table 3-17: +CBST Sett
Page 110 and 111:
Call Control The ESC command +++, t
Page 112 and 113:
Call Control +MVC, Motorola Vocoder
Page 114 and 115:
Call Control Assistant (CA) will ty
Page 116 and 117:
Call Control If there are no calls
Page 118 and 119:
Call Control +CSSN, Supplementary S
Page 120 and 121:
Call Control Table 3-26: +CSSU Noti
Page 122 and 123:
Call Control Table 3-27: +CUSD Para
Page 124 and 125:
Call Control Table 3-28: CUSD Termi
Page 126 and 127:
Page 128 and 129:
Fax Class 1 Fax Commands +FCLASS, S
Page 130 and 131:
Fax Class 1 The following table sho
Page 132 and 133:
Fax Class 1 +FRM, Receive Data This
Page 134 and 135:
Fax Class 1 +FRH, Receive DATA with
Page 136 and 137:
Phonebook and Clock The following t
Page 138 and 139:
Phonebook and Clock The following t
Page 140 and 141:
Phonebook and Clock AT+CPBF="Moto"
Page 142 and 143:
Phonebook and Clock System Date and
Page 144 and 145:
Phonebook and Clock +CCLK: "05/10/2
Page 146 and 147:
SMS The following table shows the +
Page 148 and 149:
SMS +CSCA: "*ABC#",129 // Read comm
Page 150 and 151:
SMS Note: • Incoming Status-Repor
Page 152 and 153:
SMS +CSMP, Set Text Mode Parameters
Page 154 and 155:
SMS +CSDH, Show Text Mode Parameter
Page 156 and 157:
SMS +CMGW, Write Message to Memory
Page 158 and 159:
SMS OK +CMSS, Send Message From Sto
Page 160 and 161:
SMS +CSMS, Select Message Service.
Page 162 and 163:
Page 164 and 165:
SMS In PDU mode, either positive (R
Page 166 and 167:
SMS Example AT+CPMS? +CPMS: "SM",3,
Page 168 and 169:
SMS Example AT+CNMI=1,,,2 // Set t
Page 170 and 171:
SMS +CMGR, +MMGR, Read Message Thes
Page 172 and 173:
SMS Table 3-60: +CMGR/+MMGR Paramet
Page 174 and 175:
SMS OK AT+CMGF=1 OK AT+CMGR=0 // Re
Page 176 and 177:
Page 178 and 179:
SMS than 0, the parameter is pract
Page 180 and 181:
SMS Command Type Syntax Response/Ac
Page 182 and 183:
SMS Notes: Example • A combinatio
Page 184 and 185:
SMS Table 3-66: Layout of SMS-DELIV
Page 186 and 187:
SMS Table 3-69: of SMS-COMMAND Mes
Page 188 and 189:
SMS Table 3-71: of SMS-STATUS-REPO
Page 190 and 191:
SMS DCS handling Sending or Storing
Page 192 and 193:
SMS ### Store in TEXT mode SMS enco
Page 194 and 195:
Page 196 and 197:
Network Network Network Commands +C
Page 198 and 199:
Network • GSM supports RLP Versio
Page 200 and 201:
Network +CGREG, GPRS Network Regist
Page 202 and 203:
Network +CGREG: 2, 1, A065, 988b OK
Page 204 and 205:
Network Notes: 1. The access techno
Page 206 and 207:
Network OK AT+COPS=3,2 AT+COPS? +CO
Page 208 and 209:
Network +CPOL, Preferred Operators
Page 210 and 211:
Network OK AT+CPOL? +CPOL: 000,000,
Page 212 and 213:
Network The following table shows t
Page 214 and 215:
Network OK //exec command AT+MBAND
Page 216 and 217:
Network Table 3-88: +MCI Parameters
Page 218 and 219:
Network "2G",631,,,1,,,,,, "2G",627
Page 220 and 221:
Network +WS46, Get Wireless Network
Page 222 and 223:
Network +MPDS: 1 OK AT+MPDS? +MPDS:
Page 224 and 225:
Network The following table shows t
Page 226 and 227:
Hardware Information Hardware Infor
Page 228 and 229:
Hardware Information The following
Page 230 and 231:
Hardware Information +IPR: (1-8,10-
Page 232 and 233:
Page 234 and 235:
Hardware Information +MCWAKE, GPRS
Page 236 and 237:
Hardware Information Setting report
Page 238 and 239:
Hardware Information AT+CFUN? +CFUN
Page 240 and 241:
Hardware Information Command Type S
Page 242 and 243:
Page 244 and 245:
Hardware Information Table 3-105: G
Page 246 and 247:
Hardware Information +MIOI, Motorol
Page 248 and 249:
Hardware Information +MPCMC, Contin
Page 250 and 251:
Hardware Information +MVREF, Motoro
Page 252 and 253:
Hardware Information +MFTM: (0-1) O
Page 254 and 255: Hardware Information Table 3-113: +
Page 256 and 257: Hardware Information AT+TGFCC = 1,0
Page 258 and 259: Hardware Information The following
Page 260 and 261: Hardware Information The following
Page 262 and 263: Hardware Information +MUANTYPE: 2 O
Page 264 and 265: Audio Audio General Audio Mode - Yo
Page 266 and 267: Audio +CLVL: 5 OK AT+CLVL=? +CLVL:
Page 268 and 269: Audio +CRTT, Ring Type Selection Th
Page 270 and 271: Audio OK AT+VTD? +VTD: 5 OK AT+VTD=
Page 272 and 273: Audio +MACSTG, Set CODEC ST Gain Se
Page 274 and 275: Audio The following table shows the
Page 276 and 277: Audio +MAGRST, Restore Default Gain
Page 278 and 279: Audio +MANS, Noise Suppression Cont
Page 280 and 281: Audio • FIR Filter • Automatic
Page 282 and 283: Access +CPIN, Enter PIN for Unlocki
Page 284 and 285: Access Table 3-143: +CPIN Parameter
Page 286 and 287: Access +EPIN, Enter SIM PIN2 to Ver
Page 288 and 289: Access Notes: 1. When SIM is not in
Page 290 and 291: Access +CPWD, Change Password This
Page 292 and 293: Access Command Type Syntax Response
Page 294 and 295: Access AT+CLCK="IR",2 +CLCK: 1,1 +C
Page 296 and 297: Access Example AT+MGSMSIM? +MGSMSIM
Page 298 and 299: Firmware Update Over the Air (FOTA)
Page 310 and 311: Modem Configuration and Profile The
Page 312 and 313: Modem Configuration and Profile Exa
Page 314 and 315: Modem Configuration and Profile Exa
Page 320 and 321: Modem Configuration and Profile Tab
Page 322 and 323: Modem Configuration and Profile Sle
Page 324 and 325: Modem Configuration and Profile Sle
Page 326 and 327: Modem Configuration and Profile •
Page 328 and 329: Modem Configuration and Profile Com
Page 342 and 343: UI (User Interface) The following t
Page 344 and 345: UI (User Interface) The following t
Page 346 and 347: UI (User Interface) atd035681234; O
Page 348 and 349: UI (User Interface) +MIND: (0-3),(0
Page 350 and 351: UI (User Interface) Table 3-184: +M
Page 352 and 353: UI (User Interface) Unsolicited Sta
Page 354 and 355:
UI (User Interface) Unsolicited Rep
Page 356 and 357:
GPRS/EDGE/UMTS +CGDCONT, Define PDP
Page 358 and 359:
GPRS/EDGE/UMTS at+cgdcont=3,"IP","s
Page 360 and 361:
GPRS/EDGE/UMTS The following table
Page 362 and 363:
GPRS/EDGE/UMTS Command Type Syntax
Page 364 and 365:
GPRS/EDGE/UMTS +CGQREQ, Quality of
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
GPRS/EDGE/UMTS 3G and EDGE Commands
Page 374 and 375:
Page 376 and 377:
GPRS/EDGE/UMTS Table 3-196: +CGEQRE
Page 378 and 379:
GPRS/EDGE/UMTS +CGEQMIN, 3G and EDG
Page 380 and 381:
Page 382 and 383:
GPRS/EDGE/UMTS Table 3-197: +CGEQMI
Page 384 and 385:
GPRS/EDGE/UMTS TCP/UDP IP Introduct
Page 386 and 387:
Page 388 and 389:
GPRS/EDGE/UMTS +MIPOPEN, Open a Soc
Page 390 and 391:
Page 392 and 393:
GPRS/EDGE/UMTS AT+MIPOPEN? +MIPOPEN
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
GPRS/EDGE/UMTS OK 3-332 H24 - AT Co
Page 404 and 405:
GPRS/EDGE/UMTS parameters before so
Page 406 and 407:
Page 408 and 409:
GPRS/EDGE/UMTS Example AT+MIPCONF =
Page 410 and 411:
GPRS/EDGE/UMTS +MIPRUDP, Socket Net
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
GPRS/EDGE/UMTS +MPINGSTAT, Status U
Page 418 and 419:
GPRS/EDGE/UMTS +MIPCSC, Motorola Co
Page 420 and 421:
GPRS/EDGE/UMTS Example AT+MIPCSC=?
Page 422 and 423:
GPRS/EDGE/UMTS Table 3-217: +MIPSSL
Page 424 and 425:
GPRS/EDGE/UMTS Table 3-219: Status
Page 426 and 427:
A-GPS Command Type Syntax Response/
Page 428 and 429:
A-GPS The following table shows the
Page 430 and 431:
A-GPS Using the read command H24 su
Page 432 and 433:
A-GPS Command Type Syntax Response/
Page 434 and 435:
A-GPS Example hot state. Once hot s
Page 436 and 437:
Page 438 and 439:
Page 440 and 441:
RS232 Multiplexer Feature RS232 Mul
Page 442 and 443:
RS232 Multiplexer Feature MUX State
Page 444 and 445:
RS232 Multiplexer Feature +CMUX, MU
Page 446 and 447:
Connectivity Configuration Connecti
Page 448 and 449:
Multi Channeling Multi Channeling M
Page 450 and 451:
Multi Channeling AT Commands per Ch
Page 452 and 453:
Multi Channeling +CLCK v +CLIP v v
Page 454 and 455:
Multi Channeling +CUSD v Unsolicite
Page 456 and 457:
Multi Channeling +MIPSETS v U +MIPS
Page 458 and 459:
Multi Channeling Table 3-237: Multi
Page 460 and 461:
Multi Channeling 3-390 H24 - AT Com
Page 462 and 463:
Recommended H24 Initialization afte
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
SMS SMS Managing Stored Messages in
Page 470 and 471:
SMS AT+CMGF=0 OK AT+CMGR=129 +CMGR:
Page 472 and 473:
Call Control Call Control The follo
Page 474 and 475:
Call Control atd>"ME"1117 +CME ERRO
Page 476 and 477:
Data Call Data Call Switching Modes
Page 478 and 479:
Packet Data Using the ATD* Command
Page 480 and 481:
Sleep Mode Sleep Mode Note: Note:Th
Page 482 and 483:
TCP/IP: MIP Commands Using Cases OK
Page 484 and 485:
TCP/IP: MIP Commands Using Cases +M
Page 486 and 487:
TCP/IP: MIP Commands Using Cases Ne
Page 488 and 489:
TCP/IP: MIP Commands Using Cases Af
Page 490 and 491:
TCP/IP: MIP Commands Using Cases OK
Page 492 and 493:
TCP/IP: MIP Commands Using Cases re
Page 494 and 495:
TCP/IP: MIP Commands Using Cases Fo
Page 496 and 497:
Firmware Update Over the Air (FOTA)
Page 498 and 499:
5-2 H24 - AT Commands Reference Man
Page 500 and 501:
AT Commands Alphabetical Summary +C
Page 502 and 503:
AT Commands Alphabetical Summary +C
Page 504 and 505:
AT Commands Alphabetical Summary +F
Page 506 and 507:
AT Commands Alphabetical Summary +M
Page 508 and 509:
AT Commands Alphabetical Summary +M
Page 510 and 511:
Character Set Table CS1: (GSM -> UC
Page 512 and 513:
Character Set Table CS1: (GSM -> UC
Page 514 and 515:
Character Set Table CS2: (GSM IRA)
Page 516 and 517:
Character Set Table CS2: (GSM IRA)
Page 518 and 519:
Character Set Table CS3: (UCS-2 Ful
Page 520 and 521:
Character Set Table CS4: (IRA table
Page 522 and 523:
Page 524 and 525:
Page 526 and 527:
USB Compositions 1. CDC/ACM Class i
Page 528 and 529:
ACM Driver - Modem Interface Select
Page 530 and 531:
Serial Driver - Control Interface A
Page 532 and 533:
USB Power Management Then, find you
Page 534 and 535:
D E F G C CTS D DA D DCD D DCE D DC
Page 536 and 537:
Abbreviation Full Name I L M O P I
Page 538 and 539:
Abbreviation Full Name T U V T TBD
Page 540 and 541:
B - B Index +CSSN, Supplementary Se
Page 542 and 543:
G - P Index Xon, 3-339 G GPRS Attac
Page 544 and 545:
V - W Index User Interface Commands
Page 546 and 547:
W - W Index April 15, 2010 H24 - AT
Page 548 and 549:
Page 550 and 551:
Page 552:
show all

AT Commands Reference Manual - wireless netcontrol GmbH

Create successful ePaper yourself

Delete template?

Save as template?