FS6200 Server System Implementation Guide - Public Support ...

More documents

Recommendations

Info

Setting Up and Operating the ePortal Specialty Engine By default, the ISM-0 ePortal Specialty Engine is configured as the active ePortal system and the ISM-1 ePortal Specialty Engine is configured as the standby ePortal system which is used during a failover only when ISM-0 fails or the ePortal Specialty Engine of ISM-0 fails. The active and standby ePortal system can be determined by checking the Name field of the controller from the ePortal Manager website. The active ePortal system should have the -Active suffix (for example, EP0-Active or EP1-Active) in the Controller Name field and the standby ePortal system should have the -Standby suffix (for example, EP0-Standby or EP1-Standby) in the Controller Name field. You can also determine the active ePortal system from the Component View tab of the MCP Console by checking the Host Name property when you select ePortal under the components ISM and s-Par ® . As mentioned previously, the active ePortal system has the suffix -Active as a suffix in the Host Name field. The ePortal Manager is configured with the following default setting: • ISM-0 ePortal Manager is configured to use IP address 192.168.222.190 and the name EP0-Active. The MCP backend server IP address is set to 192.168.223.250. • ISM-1 ePortal Manager is configured to use IP address 192.168.222.191 and the name EP1-Standby. The MCP backend server IP address is set to 192.168.224.250. Whenever configuration changes (for example, deploying a new application, modifying virtual server or personality module, modifying controller or back-end server configuration, and so on) are made on the active ePortal system, you must create a new backup. During the failover, the standby ePortal system uses the latest backup on the active ePortal system to restore the ePortal configuration. If the backup is not up to the date on the active ePortal system, you lose any changes since the last backup when a failover occurs from the active ePortal system to the standby ePortal system. ePortal generates the following warning alert on the Management website if the configuration is changed. Also, a new backup should be generated: Need to generate a new backup In addition, the MCP back-end server usercode and password must be configured the same on both the active and standby ePortal systems for a successful failover ISM-0 ePortal to ISM-1 ePortal Failover Transition In the event of an ISM-0 failure or ePortal Specialty Engine of ISM-0 failure while the ePortal Specialty Engine of ISM-0 is an active ePortal system, perform the following steps to recover the ePortal environment into the ePortal Specialty Engine of ISM-1: 5–12 8222 3694–000
Setting Up and Operating the ePortal Specialty Engine 1. Move both ePortal public LAN network cables from ISM-0 to ISM-1. Refer to the following figure for the LAN port locations. 2. Copy the latest ePortal backup files from ePortal IP segment 223 of ISM-0 to ePortal IP segment 224 of ISM-1 by performing the following actions from a workstation that has access to the APPLIANCES share on the MCP system: a. Map a drive to the APPLIANCES directory share on the MCP system using an MCP usercode with the EPORTALCONTROLLER GROUPCODE attribute. b. Check the APPLIANCES share for a folder named Backups\223 and Backups\224. c. If there is no folder named Backups\224 in the APPLIANCES share, create a new folder under the Backups folder in the APPLIANCES share and name it 224. d. Copy the latest backup files from the Backups\223 folder to the Backups\224 folder of the APPLIANCES share. The backup files are in the format of Backup_-.zip and Backup_-.xml. Note: You need to copy both .zip and .xml files. 8222 3694–000 5–13
Page 1 and 2:
ClearPathFS6200Server SystemImpleme
Page 3 and 4:
Contents Section 1. Introduction Ab
Page 5 and 6:
MCP Firmware Environment Policy Uti
Page 7 and 8:
Updating Specialty Engines . . . .
Page 9 and 10:
Figures 2-1. FS6200 Server Hardware
Page 11 and 12:
Tables 3-1. Physical Location of HB
Page 13 and 14:
Section 1 Introduction About This G
Page 15 and 16:
Section 2 System Overview This sect
Page 17 and 18:
• Two Processor Memory and Module
Page 19 and 20:
MCP Console s-Par Component Descrip
Page 21 and 22:
ePortal Specialty Engine The ePorta
Page 23 and 24:
Section 3 Customizing the Server Co
Page 25 and 26:
Determining Correspondence between
Page 27 and 28:
Table 3-1. Physical Location of HBA
Page 29 and 30:
• The MCP is running. • The pat
Page 31 and 32:
e. Log on to the environment. f. Cl
Page 33 and 34:
The default IP address for the intr
Page 35 and 36:
Table 3-6. Default Networking Value
Page 37 and 38:
Changing the Network Services EVLAN
Page 39 and 40:
IEEE 802.1Q VLANs allow a single ne
Page 41 and 42:
and BIP protocols. Communications b
Page 43 and 44:
4. To modify a network processor ob
Page 45 and 46:
You must replace or modify the prec
Page 47 and 48:
Table 3-8. MCP Networking Values fo
Page 49 and 50: Table 3-9. MCP Networking Values fo
Page 51 and 52: Table 3-9. MCP Networking Values fo
Page 53 and 54: Using Sample BNA Initialization Fil
Page 55 and 56: Some of the procedures in MCP Imple
Page 57 and 58: Section 4 Operating the Server This
Page 59 and 60: Powering Off the Platform Hardware
Page 61 and 62: Controlling the MCP Environment Acc
Page 63 and 64: • Domain Name System (DNS) Client
Page 65 and 66: Table 4-1. Unisys-Defined Firewall
Page 67 and 68: Table 4-2. Firewall Rules for JProc
Page 69 and 70: The utility scripts enable you to m
Page 71 and 72: Notes: Syntax Usage • Refer to th
Page 73 and 74: Sample Commands • ChangeRulesForM
Page 75 and 76: Note: The .\ notation before the sc
Page 77 and 78: Differences from Previous MCP Syste
Page 79 and 80: If you do not receive this response
Page 81 and 82: Networking Commands and Inquiries C
Page 83 and 84: • Total processor utilization rep
Page 85 and 86: I/O Time • ACQUIRE • FREE • O
Page 87 and 88: Operating the Server PING commands
Page 89 and 90: Section 5 Setting Up and Operating
Page 91 and 92: Ensuring That the Necessary Disk Sp
Page 93 and 94: ; , REMOTEADDRESS = 000000000000 ,
Page 95 and 96: This command is optional. By defaul
Page 97 and 98: 6. Perform the following actions to
Page 99: 1. From the Component View tab, exp
Page 103 and 104: Assigning ePortal Specialty Engine
Page 105 and 106: Setting Up and Operating the ePorta
Page 107 and 108: Restoring ePortal The following act
Page 109 and 110: Section 6 Setting Up and Operating
Page 111 and 112: • Microsoft Network Client This f
Page 113 and 114: Applying JProcessor Security Policy
Page 115 and 116: Section 7 Backing Up MCP Firmware C
Page 117 and 118: Section 8 Updates This section disc
Page 119 and 120: Updating MCP Firmware MCP Firmware
Page 121 and 122: Job (USERCODE) EPORTALNOTE ACCEPT:
Page 123 and 124: 17. Go back into update settings (s
Page 125 and 126: Section 9 Troubleshooting and Recov
Page 127 and 128: Accessing the Unisys Product Suppor
Page 129 and 130: Taking a Platform Firmware Livedump
Page 131 and 132: Hardware Failure Symptoms Criticali
Page 133 and 134: Workaround Use the platform managem
Page 135 and 136: • If your TCP/IP or BNA connectio
Page 137 and 138: • Obtain a Network Services firmw
Page 139 and 140: The response to the NW NP command
Page 141 and 142: Restarting a JProcessor Specialty E
Page 143 and 144: Gathering Diagnostic Information Th
Page 145 and 146: 1. Create an unprivileged MCP userc
Page 147 and 148: The topic “I/O Configuration” i
Page 149 and 150: cd “C:\Program Files\Unisys\MCP F
Page 151 and 152:
Restarting Platform Services Note:
Page 153 and 154:
Appendix A Building Network Initial
Page 155 and 156:
• NW TCPIP TCPIPIDENTITY NW TCPIP
Page 157 and 158:
Building Network Initialization Fil
Page 159 and 160:
Sample BNA Initialization File % On
Page 161 and 162:
Index A accessing the Unisys Suppor
Page 163 and 164:
MCP PING commands through intraplat
Page 165 and 166:
MAICP4 dump data, 9-13 Maintenance
Page 167 and 168:
elocating the MCP APPLIANCES share,
Page 170:
© 2012 Unisys Corporation. All rig
show all

FS6200 Server System Implementation Guide - Public Support ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?