Manual - 8500A Series Peak Power Meter - Giga-tronics
Manual - 8500A Series Peak Power Meter - Giga-tronics
Manual - 8500A Series Peak Power Meter - Giga-tronics
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Summary of Commands<br />
A.5 Graph Mode Commands<br />
Function<br />
Select Graph Mode (from<br />
single channel operation only)<br />
Autoscale<br />
Select 8501A Internal Trigger<br />
and Level<br />
Select 8502A Internal Trigger<br />
and Level<br />
Select External Trigger<br />
<strong>Peak</strong> Averaging<br />
Enter Reference Delay<br />
Clear Reference Delay<br />
GPIB Plot (Paper)<br />
GPIB Plot (Transparency)<br />
Code Number Entry for Plot<br />
Part Number Entry for Plot<br />
Abort (Stop) Plotting Activity<br />
Enter Plotter GPIB Address<br />
Set Initial Delay for<br />
Autoscaling (normal PPM<br />
operation)<br />
Set Averaging Value for<br />
Autoscaling (normal PPM<br />
operation)<br />
Command Sequence<br />
[GRAPH]<br />
[AUTOSCALE]<br />
[MENU] (1) [F1] [nn.nn] [dBm] [mW]<br />
[MENU] (1) [F1] [A] or [B] [nn.nn] [dBm] [mW]<br />
[MENU] (1) [F2]<br />
[MENU] (2) [F2] nnn [UNITS]<br />
[MENU] (4) [F1] (for ch A) or [F2] (for ch B) [nn.nn] [UNITS]<br />
[MENU] (4) [F1] (for ch A) or [F2] (for ch B) [0] [UNITS]<br />
[MENU] (2) [F3] [F1]<br />
[MENU] (2) [F3] [F2]<br />
[MENU] (5) [F1] [nnnn] [UNITS] (nnnn = up to 12 digits)<br />
[MENU] (5) [F2] [nnnn] [UNITS] (nnnn = up to 12 digits)<br />
[MENU] (6) [F1]<br />
[MENU] (6) [F2] [nn] [UNITS]<br />
[MENU] (09) [F2] [nn.nn] [UNITS]<br />
[MENU] (09) [F3] [nnn] [UNITS]<br />
*Set Initial Delay<br />
for Autoscaling<br />
(1018B emulation operation) [MENU] (11) [F2] [nn.nn] [UNITS]<br />
*Set Averaging Value<br />
for Autoscaling<br />
(1018B emulation operation) [MENU] (11) [F3] [nnn] [UNITS]<br />
*Valid only after 1018B Emulation has been entered<br />
A.5.1<br />
A.5.2<br />
Change Between Cursor, Marker, and Pulse Sub-Modes<br />
PULSE/CURSOR/MARKER<br />
Triple toggle<br />
Cursor Sub-Mode Commands<br />
Function<br />
Change Start Delay Move<br />
cursor to STRT DLY line on<br />
display, enter change using<br />
Change Window Delay Move<br />
cursor to DLY WIND line on<br />
display, enter change using<br />
Command Sequence<br />
[nn.nn] [UNITS] or spin knob<br />
[nn.nn] [UNITS] or spin knob<br />
<strong>Manual</strong> No. 20790, Rev C, November 1998 A-3<br />
Superceded by Revision D, March 2009
Change language