Manual - 8500A Series Peak Power Meter - Giga-tronics
Manual - 8500A Series Peak Power Meter - Giga-tronics
Manual - 8500A Series Peak Power Meter - Giga-tronics
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Index<br />
!<br />
1018B commands 3-38, 3-52<br />
1018B Emulation 3-38<br />
1018B Emulation Commands 3-38, 3-52<br />
1018B features not emulated by the PPM 3-40<br />
Analog output 3-39<br />
direct mode 3-39<br />
Front panel menus 3-39<br />
Initiating the 1018B emulation mode 2-47<br />
Mode functions B-3<br />
Output data modes 3-38<br />
Output format 3-38<br />
Over and under range 3-40<br />
<strong>Peak</strong> <strong>Power</strong> <strong>Meter</strong> Emulation 2-47<br />
Reference delay, correction of carrier frequency, and<br />
offset vs Remote state 3-39<br />
Two detectors 3-39<br />
A<br />
A2 Test points 4-3<br />
A3 Test points 4-7<br />
A4 Test Points 4-11<br />
A5 Test points 4-19<br />
A6/A7 Test points 4-23<br />
A8 Front panel interface board 5-12<br />
A8 Test points 4-26<br />
Address decoding and handshake 4-9<br />
Analog output 3-39<br />
Analog output accuracy test 5-7<br />
Analog PC assembly (A6/A7) 4-20<br />
Auto-Zero function 2-15<br />
Automatic functions of the Graph mode 3-24<br />
Automatic timing measurement commands 3-28<br />
Automatic window delay selection<br />
related commands 2-24, 3-26<br />
Autoscaling procedure 2-19<br />
Autoscaling procedure, external trigger 2-20<br />
Autozero detectors commands 3-15<br />
Auxiliary inputs/outputs 1-5<br />
B<br />
Backup battery circuit 4-11<br />
C<br />
CAGE<br />
List of Manufacturers 7-36<br />
Calibration<br />
Self-Calibration Procedure 2-14<br />
Calibration and Testing 5-1<br />
A8 Front panel interface board 5-12<br />
Analog output accuracy test 5-7<br />
Calibrator output level test 5-3<br />
Calibrator return loss test 5-3<br />
Delay accuracy test 5-6<br />
Detector return loss test 5-7<br />
Equipment Required 5-2<br />
Initialization 5-12<br />
Instrument plus power detector linearity test 5-3<br />
Plotter output/IEEE-488 interface 5-7<br />
<strong>Power</strong> linearity test setup 5-4<br />
Procedures 5-8<br />
Voltage proportional to frequency test 5-7<br />
Volume adjust 5-20<br />
Calibration commands 3-15<br />
Calibration Procedures 5-8<br />
Calibrator output level test 5-3<br />
Calibrator PC assembly (A12) 4-27<br />
Calibrator return loss test 5-3<br />
Calibrator specifications 1-5<br />
Change between cursor, marker,<br />
and pulse sub-modes A-5<br />
Cleaning 1-2<br />
Clock 4-16<br />
Clock gate 4-16<br />
Command string format 3-12<br />
Commands Applicable to All Modes A-1<br />
Commands for retrieving data from the PPM 3-23<br />
Commands to output graphic data to a controller 3-33<br />
Common mode functions 3-15<br />
Autozero detectors commands 3-15<br />
Calibration commands 3-15<br />
Hide and Unhide frequency information<br />
commands 3-15<br />
Output status byte information command 3-16<br />
<strong>Power</strong> limits 3-16<br />
<strong>Manual</strong> No. 20790, Rev C, November 1998<br />
Superceded by Revision D, March 2009<br />
Index-1