Manual - 8500A Series Peak Power Meter - Giga-tronics
Manual - 8500A Series Peak Power Meter - Giga-tronics
Manual - 8500A Series Peak Power Meter - Giga-tronics
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Index<br />
Output data modes 3-38<br />
Output format 3-38<br />
Output modes 3-4<br />
Plot output mode 3-8<br />
Stand alone plot output mode 3-10<br />
Status byte 3-10<br />
Temperature difference output mode 3-10<br />
Update data continuously output mode 3-7<br />
Update trigger reset output mode 3-5<br />
Output status byte information command 3-16<br />
Over and under range 3-40<br />
P<br />
Parts Lists 7-1<br />
<strong>Peak</strong> mode 2-11<br />
External triggering 2-12<br />
Internal triggering 2-12<br />
<strong>Peak</strong> Mode Commands A-3<br />
<strong>Peak</strong> power commands 3-21<br />
<strong>Peak</strong> power measurement 2-19<br />
Autoscaling procedure 2-19<br />
Autoscaling procedure, external trigger 2-20<br />
<strong>Peak</strong> power measurements (Graph mode) 2-23<br />
<strong>Peak</strong>, CW measurements 2-34<br />
<strong>Peak</strong>, peak measurements (method 1) 2-32<br />
<strong>Peak</strong>, peak measurements (method 2) 2-33<br />
Periodic Maintenance 6-1<br />
Required test equipment 6-2<br />
Plot output mode 3-8<br />
Plotter output/IEEE-488 interface 5-7<br />
Plotters supported 2-30<br />
Plotting commands 3-34<br />
<strong>Power</strong> limits 3-16<br />
<strong>Power</strong> linearity test setup 5-4<br />
<strong>Power</strong> measurement data output format 3-12<br />
Linear power data format 3-13<br />
Log (dBm) data format 3-12<br />
<strong>Power</strong> ratio measurements 2-35<br />
Ratio’ing <strong>Peak</strong> to CW signals 2-36<br />
Ratio’ing two CW signals 2-35<br />
Ratio’ing two <strong>Peak</strong> signals 2-35<br />
<strong>Power</strong> supply PC assembly (A2) 4-3<br />
A2 Test points 4-3<br />
<strong>Power</strong> warning - max/min power limits 2-37<br />
<strong>Power</strong>-On condition 3-3<br />
<strong>Power</strong>-On failure 6-3<br />
Self-test failure indications and possible causes 6-4<br />
<strong>Power</strong>-on self-test 2-10<br />
PPM IEEE bus functions 3-2<br />
PPM stand alone plot operation 3-43<br />
Procedure for making plots 2-30<br />
Programming notes 3-35<br />
PROM frequency correction 2-16<br />
External frequency 2-16<br />
User-supplied frequency 2-16<br />
Pulse parameters sub-mode functions 2-26<br />
Pulse rise time, width, and fall time 2-26<br />
Pulse rise time, width, and fall time 2-26<br />
Pulse shaper 4-18<br />
Pulse sub-mode commands A-5<br />
Pulse, cursor, and marker readouts 2-23<br />
R<br />
Ramp control logic 4-18<br />
Ramp generator 4-17<br />
range conditions<br />
Over and under range 3-40<br />
Ratioing <strong>Peak</strong> to CW signals 2-36<br />
Ratioing two CW signals 2-35<br />
Ratioing two <strong>Peak</strong> signals 2-35<br />
Reading and defining pulse parameters 3-25<br />
Real time clock 4-10<br />
Rear Panel Description 2-5<br />
Recall setup 2-45<br />
Receiving inspection 1-2<br />
Reference delay 2-40<br />
Reference delay, correction of carrier frequency, and<br />
offset vs 1018B direct mode 3-39<br />
Reference <strong>Power</strong> 2-25<br />
Reference power related commands 3-27<br />
Related peak power commands 3-22<br />
Remote and local lockout functions 3-4<br />
Remote Operating Modes 3-2<br />
Command string format 3-12<br />
Front panel menus 3-3<br />
Output modes 3-4<br />
<strong>Power</strong> measurement data output format 3-12<br />
<strong>Power</strong>-On condition 3-3<br />
PPM IEEE bus functions 3-2<br />
Remote and local lockout functions 3-4<br />
Remote Operation 3-1<br />
1018B Emulation 3-38<br />
1018B Emulation Commands 3-38, 3-52<br />
Data Formats 3-52<br />
GPIB Command Descriptions 3-14<br />
GPIB Command Summary 3-44<br />
Remote Operating Modes 3-2<br />
Service Requests 3-36<br />
<strong>Manual</strong> No. 20790, Rev C, November 1998<br />
Superceded by Revision D, March 2009<br />
Index-5