Specifications - State of Delaware

More documents

Recommendations

Info

SECTION 095123 - ACOUSTICAL TILE CEILINGS: continued 6. Do not support ceilings directly from permanent metal forms or floor deck. Fasten hangers to cast-in-place hanger inserts, postinstalled mechanical or adhesive anchors, or power-actuated fasteners that extend through forms into concrete. 7. When steel framing does not permit installation of hanger wires at spacing required, install carrying channels or other supplemental support for attachment of hanger wires. 8. Do not attach hangers to steel deck tabs. 9. Do not attach hangers to steel roof deck. Attach hangers to structural members. 10. Space hangers not more than 48 inches o.c. along each member supported directly from hangers unless otherwise indicated; provide hangers not more than 8 inches from ends of each member. 11. Size supplemental suspension members and hangers to support ceiling loads within performance limits established by referenced standards and publications. C. Secure bracing wires to ceiling suspension members and to supports with a minimum of four tight turns. Suspend bracing from building's structural members as required for hangers without attaching to permanent metal forms, steel deck, or steel deck tabs. Fasten bracing wires into concrete with cast-in-place or postinstalled anchors. D. Install suspension-system runners so they are square and securely interlocked with one another. Remove and replace dented, bent, or kinked members. E. Arrange acoustical tiles as follows: 1. Install tiles in a basket-weave pattern. F. Install acoustical tiles in coordination with suspension system and exposed moldings and trim. Place splines or suspension-system flanges into kerfed edges so tile-to-tile joints are closed by double lap of material. 1. Fit adjoining tile to form flush, tight joints. Scribe and cut tile for accurate fit at borders and around penetrations through tile. 2. Hold tile field in compression by inserting leaf-type, spring-steel spacers between tile and moldings, spaced 12 inches o.c. 3. Protect lighting fixtures and air ducts to comply with requirements indicated for fireresistance-rated assembly. 3.04 FIELD QUALITY CONTROL: A. Special Inspections: Engage a qualified special inspector to perform the following special inspections: 1. Compliance of seismic design. B. Perform the following tests and inspections of completed installations of acoustical tile ceiling hangers and anchors and fasteners in successive stages and when installation of ceiling suspension systems on each floor has reached 20% completion but no tiles have been installed. Do not proceed with installations of acoustical tile ceiling hangers for the next area until test results for previously completed installations of acoustical tile ceiling hangers show compliance with requirements. 1. Within each test area, testing agency will select one of every 10 power-actuated fasteners and postinstalled anchors used to attach hangers to concrete and will test them for 200 lbf of tension; it will also select one of every two postinstalled anchors used to attach bracing wires to concrete and will test them for 440 lbf of tension. 2. When testing discovers fasteners and anchors that do not comply with requirements, testing agency will test those anchors not previously tested until 20 pass consecutively and then will resume initial testing frequency. C. Acoustical tile ceiling hangers and anchors and fasteners will be considered defective if they do not pass tests and inspections. DEAN095123.DOC 095123-7
SECTION 095123 - ACOUSTICAL TILE CEILINGS: continued D. Prepare test and inspection reports. 3.05 CLEANING: A. Clean exposed surfaces of acoustical tile ceilings, including trim and edge moldings. Comply with manufacturer's written instructions for cleaning and touchup of minor finish damage. Remove and replace tiles and other ceiling components that cannot be successfully cleaned and repaired to permanently eliminate evidence of damage. END OF SECTION 095123 095123-8 DEAN095123.DOC
Page 1 and 2:
TABLE OF CONTENTS Instructions to B
Page 3 and 4:
PROJECT 62134 - TABLE OF CONTENTS:
Page 5:
PROJECT 62134 - TABLE OF CONTENTS:
Page 8 and 9:
ids on this contract and will not b
Page 10 and 11:
STATE OF DELAWARE DELAWARE NATIONAL
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36:
Page 39 and 40:
TABLE OF ARTICLES 1 THE CONTRACT DO
Page 41 and 42:
§ 5.1.5 Applications for Payment s
Page 43 and 44:
« » « » « » « » « » « »
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
BETHANY BEACH TRAINING SITE DEARNG
Page 59 and 60:
Page 61:
Page 64 and 65:
Any proceeding, legal or equitable,
Page 66 and 67:
transferees shall have the same eff
Page 68:
1 AIA ® Document G702 - 1992 Appli
Page 74 and 75:
SECTION 011000 - SUMMARY: continued
Page 76 and 77:
SECTION 011000 - SUMMARY: continued
Page 78 and 79:
SECTION 012300 - ALTERNATES: CONTIN
Page 80 and 81:
SECTION 012500 - SUBSTITUTION PROCE
Page 82 and 83:
SECTION 012600 - CONTRACT MODIFICAT
Page 84 and 85:
SECTION 012900 - PAYMENT PROCEDURES
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
SECTION 013100 - PROJECT MANAGEMENT
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
SECTION 013200 - CONSTRUCTION PROGR
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
SECTION 013300 - SUBMITTAL PROCEDUR
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
SECTION 013526 - GOVERNMENTAL SAFET
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
SECTION 014200 - REFERENCES: contin
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
SECTION 014500 - QUALITY CONTROL: c
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
SECTION 015000 - TEMPORARY FACILITI
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
SECTION 016000 - PRODUCT REQUIREMEN
Page 182 and 183:
SECTION 016000 - PRODUCT REQUIREMEN
Page 184 and 185:
SECTION 017300 - EXECUTION: continu
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
SECTION 017419 - CONSTRUCTION WASTE
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
SECTION 017700 - CLOSEOUT PROCEDURE
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
SECTION 017823 - OPERATION AND MAIN
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
SECTION 017839 - PROJECT RECORD DOC
Page 214 and 215:
SECTION 017839 - PROJECT RECORD DOC
Page 216 and 217:
SECTION 017900 - DEMONSTRATION AND
Page 218 and 219:
SECTION 017900 - DEMONSTRATION AND
Page 220 and 221:
SECTION 018113.13 - SUSTAINABLE DES
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
LEED 2009 for New Construction and
Page 232 and 233:
SECTION 019113 GENERAL COMMISSIONIN
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
SECTION 024116 - STRUCTURE DEMOLITI
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
SECTION 033000 - CAST-IN-PLACE CONC
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
SECTION 042000 - UNIT MASONRY: cont
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
DIVISION 05 - METALS SECTION 051200
Page 284 and 285:
SECTION 051200 - STRUCTURAL STEEL F
Page 286 and 287:
SECTION 051200 - STRUCTURAL STEEL F
Page 288 and 289:
SECTION 053100 - STEEL DECKING PART
Page 290 and 291:
SECTION 053100 - STEEL DECKING: con
Page 292 and 293:
SECTION 054000 - COLD-FORMED METAL
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
SECTION 055000 - METAL FABRICATIONS
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
DIVISION 06 - WOOD AND PLASTICS SEC
Page 312 and 313:
SECTION 061000 - ROUGH CARPENTRY: c
Page 314 and 315:
SECTION 061000 - ROUGH CARPENTRY: c
Page 316 and 317:
SECTION 064023 - INTERIOR ARCHITECT
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
SECTION 070910 BUILDING ENVELOPE EN
Page 326 and 327:
PART 2 - PRODUCTS Not Applicable f.
Page 328 and 329:
3.4 NON-CONFORMANCE A. All deficien
Page 330 and 331:
SECTION 072100 - THERMAL INSULATION
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
SECTION 073113 - ASPHALT SHINGLES P
Page 338 and 339:
SECTION 073113 - ASPHALT SHINGLES:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
SECTION 075419 - POLYVINYL-CHLORIDE
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
SECTION 076200 - SHEET METAL FLASHI
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
SECTION 079200 - JOINT SEALANTS: co
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
DIVISION 08 - DOORS AND WINDOWS SEC
Page 376 and 377:
SECTION 081113 - HOLLOW METAL DOORS
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
SECTION 081416 - FLUSH WOOD DOORS:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
SECTION 083113 - ACCESS DOORS AND F
Page 392 and 393:
SECTION 083113 - ACCESS DOORS AND F
Page 394 and 395:
SECTION 084113 - ALUMINUM-FRAMED EN
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
SECTION 085113 - ALUMINUM WINDOWS:
Page 410 and 411:
Page 412 and 413:
Page 414 and 415:
SECTION 087100 - DOOR HARDWARE PART
Page 416 and 417:
SECTION 087100 - DOOR HARDWARE: con
Page 418 and 419:
Page 420 and 421:
Page 422 and 423: SECTION 087100 - DOOR HARDWARE: con
Page 430 and 431: SECTION 088000 - GLAZING: continued
Page 442 and 443: SECTION 089000 - LOUVERS AND VENTS:
Page 448 and 449: SECTION 092216 - NON-STRUCTURAL MET
Page 450 and 451: SECTION 092216 - NON-STRUCTURAL MET
Page 452 and 453: SECTION 092900 - GYPSUM BOARD PART
Page 454 and 455: SECTION 092900 - GYPSUM BOARD: cont
Page 460 and 461: SECTION 093000 - PORCELAIN TILE PAR
Page 462 and 463: SECTION 093000 - PORCELAIN TILE: co
Page 464 and 465: SECTION 093000 - PORCELAIN TILE: co
Page 466 and 467: SECTION 095123 - ACOUSTICAL TILE CE
Page 474 and 475: SECTION 096513 - RESILIENT BASE AND
Page 480 and 481: SECTION 096519 - RESILIENT TILE FLO
Page 482 and 483: SECTION 096519 - RESILIENT TILE FLO
Page 484 and 485: SECTION 096813 - TILE CARPETING PAR
Page 486 and 487: SECTION 096813 - TILE CARPETING: co
Page 488 and 489: SECTION 096813 - TILE CARPETING: co
Page 490 and 491: SECTION 099113 - EXTERIOR PAINTING
Page 492 and 493: SECTION 099113 - EXTERIOR PAINTING:
Page 494 and 495: SECTION 099113 - EXTERIOR PAINTING:
Page 496 and 497: SECTION 099123 - INTERIOR PAINTING
Page 498 and 499: SECTION 099123 - INTERIOR PAINTING:
Page 506 and 507: SECTION 101100 - MARKERBOARDS AND T
Page 508 and 509: SECTION 101400 - SIGNAGE PART 1 - G
Page 510 and 511: SECTION 101400 - SIGNAGE: continued
Page 516 and 517: SECTION 102113 - TOILET COMPARTMENT
Page 518 and 519: SECTION 102113 - TOILET COMPARTMENT
Page 520 and 521: SECTION 102226 - FOLDING PANEL PART
Page 522 and 523:
SECTION 102226 - OPERABLE PARTITION
Page 524 and 525:
Page 526 and 527:
Page 528 and 529:
SECTION 102800 - TOILET, BATH, AND
Page 530 and 531:
Page 532 and 533:
Page 534 and 535:
SECTION 104413 - FIRE EXTINGUISHER
Page 536 and 537:
SECTION 104413 - FIRE EXTINGUISHER
Page 538 and 539:
DIVISION 11 - EQUIPMENT SECTION 115
Page 540 and 541:
SECTION 115213 - AUDIO-VISUAL EQUIP
Page 542 and 543:
DIVISION 12 - FURNISHINGS SECTION 1
Page 544 and 545:
SECTION 122113 - HORIZONTAL LOUVER
Page 546 and 547:
SECTION 124813 - ENTRANCE FLOOR MAT
Page 548 and 549:
SECTION 124813 - ENTRANCE FLOOR MAT
Page 550 and 551:
SECTION 133423 - FABRICATED STRUCTU
Page 552 and 553:
Page 554 and 555:
Page 556 and 557:
SECTION 211000 - FIRE-SUPPRESSION P
Page 558 and 559:
Page 560 and 561:
Page 562 and 563:
Page 564 and 565:
Page 566 and 567:
Page 568 and 569:
Page 570 and 571:
SECTION 213113 - ELECTRIC-DRIVE, CE
Page 572 and 573:
Page 574 and 575:
Page 576 and 577:
9. During the startup and initial c
Page 578 and 579:
DIVISION 22 - PLUMBING SECTION 2209
Page 580 and 581:
SECTION 220910 PLUMBING SYSTEMS COM
Page 582 and 583:
SECTION 220910 PLUMBING SYSTEMS COM
Page 584 and 585:
SECTION 221116 - DOMESTIC WATER PIP
Page 586 and 587:
Page 588 and 589:
Page 590 and 591:
Page 592 and 593:
Page 594 and 595:
Page 596 and 597:
Page 598 and 599:
SECTION 221316 - SANITARY WASTE AND
Page 600 and 601:
Page 602 and 603:
Page 604 and 605:
SECTION 221319 - SANITARY WASTE PIP
Page 606 and 607:
Page 608 and 609:
Page 610 and 611:
SECTION 223300 - ELECTRIC WATER HEA
Page 612 and 613:
SECTION 224000 - PLUMBING FIXTURES
Page 614 and 615:
SECTION 224000 - PLUMBING FIXTURES:
Page 616 and 617:
Page 618 and 619:
Page 620 and 621:
Page 622 and 623:
Page 624 and 625:
SECTION 224700 - DRINKING FOUNTAINS
Page 626 and 627:
SECTION 224700 - DRINKING FOUNTAINS
Page 628 and 629:
DIVISION 23 - HVAC SECTION 230500 -
Page 630 and 631:
SECTION 230500 - BASIC MECHANICAL M
Page 632 and 633:
Page 634 and 635:
Page 636 and 637:
Page 638 and 639:
SECTION 230513 - MOTORS PART 1 - GE
Page 640 and 641:
SECTION 230513 - MOTORS: continued
Page 642 and 643:
SECTION 230519 - METERS AND GAUGES:
Page 644 and 645:
SECTION 230523 - VALVES PART 1 - GE
Page 646 and 647:
SECTION 230523 - VALVES: continued
Page 648 and 649:
Page 650 and 651:
Page 652 and 653:
SECTION 230529 - HANGERS AND SUPPOR
Page 654 and 655:
Page 656 and 657:
Page 658 and 659:
Page 660 and 661:
SECTION 230548 - MECHANICAL VIBRATI
Page 662 and 663:
Page 664 and 665:
Page 666 and 667:
SECTION 230553 - MECHANICAL IDENTIF
Page 668 and 669:
Page 670 and 671:
Page 672 and 673:
SECTION 230593 - TESTING, ADJUSTING
Page 674 and 675:
Page 676 and 677:
Page 678 and 679:
Page 680 and 681:
Page 682 and 683:
Page 684 and 685:
Page 686 and 687:
Page 688 and 689:
SECTION 230700 - MECHANICAL INSULAT
Page 690 and 691:
Page 692 and 693:
Page 694 and 695:
Page 696 and 697:
Page 698 and 699:
Page 700 and 701:
Page 702 and 703:
Page 704 and 705:
Page 706 and 707:
SECTION 230900 - HVAC INSTRUMENTATI
Page 708 and 709:
Page 710 and 711:
Page 712 and 713:
Page 714 and 715:
Page 716 and 717:
Page 718 and 719:
SECTION 230910 MECHANICAL SYSTEMS C
Page 720 and 721:
Page 722 and 723:
Page 724 and 725:
Page 726 and 727:
Page 728 and 729:
SECTION 232113 - HYDRONIC PIPING: c
Page 730 and 731:
Page 732 and 733:
Page 734 and 735:
Page 736 and 737:
Page 738 and 739:
SECTION 232114 - OUTDOOR GEOTHERMAL
Page 740 and 741:
Page 742 and 743:
Page 744 and 745:
Page 746 and 747:
Page 748 and 749:
Page 750 and 751:
SECTION 232123 - HYDRONIC PUMPS PAR
Page 752 and 753:
SECTION 232123 - HYDRONIC PUMPS: co
Page 754 and 755:
SECTION 232300 - REFRIGERANT PIPING
Page 756 and 757:
Page 758 and 759:
Page 760 and 761:
Page 762 and 763:
SECTION 233113 - METAL DUCTS PART 1
Page 764 and 765:
SECTION 233113 - METAL DUCTS: conti
Page 766 and 767:
Page 768 and 769:
Page 770 and 771:
SECTION 233300 - DUCT ACCESSORIES P
Page 772 and 773:
SECTION 233300 - DUCT ACCESSORIES:
Page 774 and 775:
SECTION 233300 - DUCT ACCESSORIES:
Page 776 and 777:
SECTION 233423 - POWER VENTILATORS
Page 778 and 779:
SECTION 233423 POWER VENTILATORS: c
Page 780 and 781:
SECTION 233700 - AIR TERMINAL UNITS
Page 782 and 783:
SECTION 233700 - AIR TERMINAL UNITS
Page 784 and 785:
SECTION 233713 - DIFFUSERS, REGISTE
Page 786 and 787:
SECTION 237314 - INDOOR DEDICATED O
Page 788 and 789:
Page 790 and 791:
Page 792 and 793:
Page 794 and 795:
Page 796 and 797:
SECTION 238126 - SPLIT-SYSTEM AIR-C
Page 798 and 799:
SECTION 238126 - SPLIT-SYSTEM AIR-C
Page 800 and 801:
SECTION 238146 - WATER-SOURCE HEAT
Page 802 and 803:
Page 804 and 805:
Page 806 and 807:
SECTION 238240 - PROPELLER UNIT HEA
Page 808 and 809:
SECTION 238241 - WALL AND CEILING H
Page 810 and 811:
DIVISION 26 - ELECTRICAL SECTION 26
Page 812 and 813:
SECTION 260000 - BASIC ELECTRICAL R
Page 814 and 815:
SECTION 260000 - BASIC ELECTRICAL R
Page 816 and 817:
SECTION 260516 - WIRES AND CABLES:
Page 818 and 819:
SECTION 260516 - WIRES AND CABLES:
Page 820 and 821:
SECTION 260526 - GROUNDING: continu
Page 822 and 823:
SECTION 260526 - GROUNDING: continu
Page 824 and 825:
SECTION 260529 - SUPPORTING DEVICES
Page 826 and 827:
SECTION 260529 - SUPPORTING DEVICES
Page 828 and 829:
SECTION 260533 - RACEWAYS: continue
Page 830 and 831:
Page 832 and 833:
Page 834 and 835:
Page 836 and 837:
SECTION 260534 - ELECTRICAL BOXES A
Page 838 and 839:
SECTION 260534 - ELECTRICAL BOXES A
Page 840 and 841:
SECTION 260536 - CABLE TRAY PART 1
Page 842 and 843:
SECTION 260536 - CABLE TRAY: contin
Page 844 and 845:
SECTION 260553 - ELECTRICAL IDENTIF
Page 846 and 847:
Page 848 and 849:
Page 850 and 851:
SECTION 260910 - ELECTRICAL SYSTEMS
Page 852 and 853:
SECTION 260910 - ELECTRICAL SYSTEMS
Page 854 and 855:
SECTION 262213 - TRANSFORMERS: cont
Page 856 and 857:
SECTION 262213 - TRANSFORMERS: cont
Page 858 and 859:
SECTION 262416 - PANELBOARDS: conti
Page 860 and 861:
Page 862 and 863:
Page 864 and 865:
SECTION 262726 - WIRING DEVICES: co
Page 866 and 867:
SECTION 262726 - WIRING DEVICES: co
Page 868 and 869:
SECTION 262730 - ELECTRICAL CONNECT
Page 870 and 871:
SECTION 262730 - ELECTRICAL CONNECT
Page 872 and 873:
SECTION 262816 - CIRCUIT AND MOTOR
Page 874 and 875:
SECTION 262900 - MOTOR CONTROLLERS,
Page 876 and 877:
Page 878 and 879:
Page 880 and 881:
Page 882 and 883:
Page 884 and 885:
SECTION 263600 - TRANSFER SWITCHES:
Page 886 and 887:
SECTION 263600 - TRANSFER SWITCHES:
Page 888 and 889:
SECTION 264100 - LIGHTNING PROTECTI
Page 890 and 891:
SECTION 264300 - TRANSIENT VOLTAGE
Page 892 and 893:
SECTION 264300 - TRANSIENT VOLTAGE
Page 894 and 895:
SECTION 265000 - INTERIOR LIGHTING
Page 896 and 897:
Page 898 and 899:
Page 900 and 901:
SECTION 265200 - EMERGENCY LIGHTING
Page 902 and 903:
SECTION 265610 - EXTERIOR LIGHTING
Page 904 and 905:
Page 906 and 907:
Page 908 and 909:
SECTION 271100 - COMMUNICATIONS EQU
Page 910 and 911:
SECTION 271100 - COMMUNICATIONS EQU
Page 912 and 913:
SECTION 271300 - COMMUNICATIONS BAC
Page 914 and 915:
Page 916 and 917:
Page 918 and 919:
Page 920 and 921:
Page 922 and 923:
SECTION 271500 - COMMUNICATIONS HOR
Page 924 and 925:
Page 926 and 927:
Page 928 and 929:
Page 930 and 931:
Page 932 and 933:
DIVISION 28 - ELECTRONIC SAFETY AND
Page 934 and 935:
SECTION 283100 - FIRE ALARM SYSTEMS
Page 936 and 937:
Page 938 and 939:
Page 940 and 941:
Page 942 and 943:
SECTION 311000 SITE CLEARING: conti
Page 944 and 945:
SECTION 312000 - EARTH MOVING PART
Page 946 and 947:
SECTION 312000 - EARTH MOVING: cont
Page 948 and 949:
Page 950 and 951:
Page 952 and 953:
Page 954 and 955:
SECTION 312319 - DEWATERING PART 1
Page 956 and 957:
SECTION 312319 - DEWATERING: contin
Page 958 and 959:
SECTION 312500 - EROSION AND SEDIME
Page 960 and 961:
SECTION 315000 - EXCAVATION SUPPORT
Page 962 and 963:
SECTION 315000 - EXCAVATION SUPPORT
Page 964 and 965:
DIVISION 32 - EXTERIOR IMPROVEMENTS
Page 966 and 967:
SECTION 320523 - CONCRETE SIDEWALKS
Page 968 and 969:
SECTION 321200 - FLEXIBLE PAVING: c
Page 970 and 971:
SECTION 321200 - FLEXIBLE PAVING: c
Page 972 and 973:
SECTION 321613 - CONCRETE CURB AND
Page 974 and 975:
SECTION 321723 - PAVEMENT MARKING P
Page 976 and 977:
SECTION 329200 - TURF AND GRASSES P
Page 978 and 979:
SECTION 329200 - TURF AND GRASSES:
Page 980 and 981:
DIVISION 33 - UTIILITIES SECTION 33
Page 982 and 983:
SECTION 331100 - WATER UTILITY DIST
Page 984 and 985:
SECTION 331200 - WATER UTILITY DIST
Page 986 and 987:
SECTION 333100 - SANITARY UTILITY S
Page 988 and 989:
Page 990 and 991:
Page 992 and 993:
SECTION 334100 - STORM UTILITY DRAI
Page 994:
SECTION 334900 - STORM DRAINAGE STR
show all

Specifications - State of Delaware

Create successful ePaper yourself

Delete template?

Save as template?