Xilinx Constraints Guide

More documents

Recommendations

Info

Chapter 4: Xilinx Constraints DCI Value (DCI_VALUE) Architecture Support Applicable Elements DCI Value (DCI_VALUE) determines which buffer behavioral models are associated with the IOBs of a design in the generation of an IBS file using IBISWriter. Supports Virtex®-4, Virtex-5, Virtex-6, and Spartan®-3 devices. IOBs Propagation Rules Applies to the IOB to which it is attached. Syntax Examples The following examples show how to use this constraint with particular tools or methods. If a tool or method is not listed, you cannot use this constraint with it. UCF and NCF Syntax INST pin_name DCI_VALUE = integer; where • Legal values are integers 25 through 100 with an implied units of ohms. • The default value is 50 ohms. Constraints Guide 94 www.xilinx.com UG625 (v. 13.2) July 6, 2011
Default (DEFAULT) Chapter 4: Xilinx Constraints The Default (DEFAULT) constraint allows you to set a new default value for several constraints. A specific constraint overrides the DEFAULT constraint value where applicable. Termination is the constraint name for the following: • KEEPER • FLOAT • PULLDOWN • PULLUP Architecture Support The DEFAULT constraint applies to the following constraints and their architectures: • KEEPER, PULLDOWN Applies to all FPGA devices and the CoolRunner-II CPLD device. • PULLUP Applicable Elements Applies to all FPGA devices and the CoolRunner XPLA3 and CoolRunner-II CPLD devices. For the applicable elements for each of the constraints supported by DEFAULT, see: • KEEPER • FLOAT • PULLDOWN • PULLUP Propagation Rules For the propagation rules for each of the constraints supported by DEFAULT, see: • KEEPER • FLOAT • PULLDOWN • PULLUP Constraint Syntax For the syntax rules for each of the constraints supported by DEFAULT, see: • KEEPER • FLOAT • PULLDOWN • PULLUP Syntax Examples The following examples show how to use this constraint with particular tools or methods. If a tool or method is not listed, you cannot use this constraint with it. Constraints Guide UG625 (v. 13.2) July 6, 2011 www.xilinx.com 95
Page 1 and 2:
Constraints Guide UG625 (v. 13.2) J
Page 3 and 4:
Table of Contents Revision History
Page 5 and 6:
IBUF_DELAY_VALUE (Input Buffer Dela
Page 7 and 8:
Constraint Types Attributes and Con
Page 9 and 10:
Grouping Constraints for Timing Cha
Page 11 and 12:
The name qualifier can include the
Page 13 and 14:
Physical Constraints Mapping Note T
Page 15 and 16:
Placement Constraints Chapter 1: Co
Page 17 and 18:
Routing Directives Routing directiv
Page 19 and 20:
Timing Constraints Chapter 1: Const
Page 21 and 22:
UCF Timing Constraint Support From-
Page 23 and 24:
Timing Model Constraint Priority Ch
Page 25 and 26:
Chapter 2 Entry Strategies for Xili
Page 27 and 28:
Constraint Schematic VHDL Verilog L
Page 29 and 30:
An attribute can be declared in an
Page 31 and 32:
User Constraints File (UCF) UCF Flo
Page 33 and 34:
Syntax Chapter 2: Entry Strategies
Page 35 and 36:
Entering Multiple Constraints File
Page 37 and 38:
Chapter 2: Entry Strategies for Xil
Page 39 and 40:
Running Constraints Editor As a Sta
Page 41 and 42:
Defining I/O Pin Configurations Cha
Page 43 and 44: Placement LOC Constraint Assignment
Page 45 and 46: Verilog Example -------------module
Page 47 and 48: Chapter 2: Entry Strategies for Xil
Page 49 and 50: Timing Specification Priorities Cha
Page 51 and 52: Timing Constraint Strategies Chapte
Page 53 and 54: Chapter 3: Timing Constraint Strate
Page 55 and 56: The global OFFSET IN constraint for
Page 57 and 58: The PERIOD constraint syntax for th
Page 59 and 60: Example Chapter 3: Timing Constrain
Page 61 and 62: Chapter 3: Timing Constraint Strate
Page 63 and 64: The global OFFSET OUT constraints f
Page 65 and 66: Multi-Cycle Paths Chapter 3: Timing
Page 67 and 68: Xilinx Constraints Each Xilinx® co
Page 69 and 70: RANGE Chapter 4: Xilinx Constraints
Page 71 and 72: Chapter 4: Xilinx Constraints Range
Page 73 and 74: COMPRESSION GROUP PLACE Chapter 4:
Page 75 and 76: Defining From Timing Groups Chapter
Page 77 and 78: BEL (BEL) The BEL (BEL) constraint:
Page 79 and 80: BLKNM (Block Name) Architecture Sup
Page 81 and 82: BUFG (BUFG) The BUFG (BUFG) constra
Page 83 and 84: Clock Dedicated Route (CLOCK_DEDICA
Page 85 and 86: COMPGRP (Component Group) Architect
Page 87 and 88: • S_SELECTMAP16 Slave SelectMAP M
Page 89 and 90: Verilog Syntax Chapter 4: Xilinx Co
Page 93: PCF Syntax CONFIG DCI_CASCADE = ",
Page 97 and 98: Example (* KEEPER = “TRUE” *) D
Page 99 and 100: DIFF_TERM (Diff_Term) Architecture
Page 101 and 102: DIRECTED_ROUTING (Directed Routing)
Page 103 and 104: DISABLE (Disable) The DISABLE (Disa
Page 105 and 106: DRIVE (Drive) The DRIVE (Drive) con
Page 107 and 108: XCF Syntax MODEL “entity_name”
Page 109 and 110: ENABLE (Enable) The ENABLE (Enable)
Page 111 and 112: ENABLE_SUSPEND (Enable Suspend) Arc
Page 115 and 116: Constraints Editor Syntax Chapter 4
Page 117 and 118: VHDL Syntax Declare the VHDL constr
Page 119 and 120: UCF and NCF Syntax NET “signal_na
Page 121 and 122: Chapter 4: Xilinx Constraints You a
Page 123 and 124: Constraints Editor Syntax Chapter 4
Page 125 and 126: HBLKNM (Hierarchical Block Name) Ar
Page 127 and 128: HIODELAY_GROUP (HIODELAY Group) Arc
Page 129 and 130: VHDL Syntax Declare the VHDL constr
Page 131 and 132: HU_SET (HU Set) The HU_SET (HU Set)
Page 133 and 134: IBUF_DELAY_VALUE (Input Buffer Dela
Page 135 and 136: IFD_DELAY_VALUE (IFD Delay Value) T
Page 137 and 138: IN_TERM (In Term) Architecture Supp
Page 139 and 140: INREG (Input Registers) Architectur
Page 141 and 142: IOB (IOB) The IOB constraint: • I
Page 143 and 144: IOBDELAY (Input Output Block Delay)
Page 145 and 146:
IODELAY_GROUP (IODELAY Group) Limit
Page 147 and 148:
IOSTANDARD (Input Output Standard)
Page 149 and 150:
Pinout and Area Constraints Editor
Page 151 and 152:
Verilog Syntax Chapter 4: Xilinx Co
Page 153 and 154:
Architecture Support Applicable Ele
Page 155 and 156:
Keeper (KEEPER) Architecture Suppor
Page 157 and 158:
LOC (Location) The LOC (Location) c
Page 159 and 160:
Chapter 4: Xilinx Constraints The w
Page 161 and 162:
LOC Range Constraint Examples Const
Page 163 and 164:
PlanAhead Syntax Chapter 4: Xilinx
Page 165 and 166:
Schematic LOC=P17 Chapter 4: Xilinx
Page 167 and 168:
Example One Chapter 4: Xilinx Const
Page 169 and 170:
Slices Prohibited Example Two Chapt
Page 171 and 172:
LOCK_PINS (Lock Pins) Architecture
Page 173 and 174:
where value is any chosen name unde
Page 175 and 176:
MAP (Map) Architecture Support Appl
Page 177 and 178:
Specify the Verilog constraint as f
Page 179 and 180:
Architecture Support Applicable Ele
Page 181 and 182:
MAXDELAY (Maximum Delay) Architectu
Page 183 and 184:
PCF Syntax item MAXDELAY = maxvalue
Page 185 and 186:
MAXSKEW (Maximum Skew) The MAXSKEW
Page 187 and 188:
FPGA Editor Syntax Chapter 4: Xilin
Page 189 and 190:
MIODELAY_GROUP (MIODELAY Group) Arc
Page 191 and 192:
VHDL Syntax Declare the VHDL constr
Page 193 and 194:
UCF and NCF Syntax Chapter 4: Xilin
Page 195 and 196:
where Chapter 4: Xilinx Constraints
Page 197 and 198:
Falling Edge Constraints Chapter 4:
Page 199 and 200:
PlanAhead Syntax Chapter 4: Xilinx
Page 201 and 202:
where Chapter 4: Xilinx Constraints
Page 203 and 204:
UCF Syntax NET “clock” TNM_NET
Page 205 and 206:
Page 207 and 208:
Attribute OUT_TERM: string; Specify
Page 209 and 210:
TIMESPEC PERIOD Method Chapter 4: X
Page 211 and 212:
Examples of a Primary Clock with De
Page 213 and 214:
where • period is the required cl
Page 215 and 216:
New PERIOD Specifications Output Pi
Page 217 and 218:
Post CRC (POST_CRC) Architecture Su
Page 219 and 220:
Post CRC Frequency (POST_CRC_FREQ)
Page 221 and 222:
Post CRC Signal (POST_CRC_SIGNAL) A
Page 223 and 224:
PRIORITY (Priority) Architecture Su
Page 225 and 226:
The following are not supported: Ch
Page 227 and 228:
PULLDOWN (Pulldown) Architecture Su
Page 229 and 230:
PULLUP (Pullup) Architecture Suppor
Page 231 and 232:
PWR_MODE (Power Mode) Architecture
Page 233 and 234:
REG (Registers) The REG (Registers)
Page 235 and 236:
RLOC (Relative Location) The Relati
Page 237 and 238:
RLOC = X3Y4 Chapter 4: Xilinx Const
Page 239 and 240:
Linking Sets Set Linkage Chapter 4:
Page 241 and 242:
Chapter 4: Xilinx Constraints by th
Page 243 and 244:
Linking Two HU_SET Sets Chapter 4:
Page 245 and 246:
Specify the VHDL constraint as foll
Page 247 and 248:
Chapter 4: Xilinx Constraints Diffe
Page 249 and 250:
H_SET (H Set) Chapter 4: Xilinx Con
Page 251 and 252:
Chapter 4: Xilinx Constraints The n
Page 253 and 254:
Syntax Examples Chapter 4: Xilinx C
Page 255 and 256:
RLOC_RANGE (Relative Location Range
Page 257 and 258:
where the relative X values (m1 and
Page 259 and 260:
Page 261 and 262:
UCF and NCF Syntax NET “mysignal
Page 263 and 264:
Page 265 and 266:
VHDL Syntax Chapter 4: Xilinx Const
Page 267 and 268:
SLOW (Slow) The SLOW (Slow) constra
Page 269 and 270:
STEPPING (Stepping) Architecture Su
Page 271 and 272:
VHDL Syntax Chapter 4: Xilinx Const
Page 273 and 274:
Page 275 and 276:
Constraints Editor Syntax Chapter 4
Page 277 and 278:
Chapter 4: Xilinx Constraints The f
Page 279 and 280:
TIMEGRP (Timing Group) The TIMEGRP
Page 281 and 282:
Defining Latch Subgroups by Gate Se
Page 283 and 284:
Chapter 4: Xilinx Constraints When
Page 285 and 286:
PCF Syntax TIMEGRP name; TIMEGRP na
Page 287 and 288:
Separators FROM-TO Syntax TIMESPEC
Page 289 and 290:
TNM (Timing Name) Chapter 4: Xilinx
Page 291 and 292:
Chapter 4: Xilinx Constraints A qua
Page 293 and 294:
TNM_NET (Timing Name Net) The TNM_N
Page 295 and 296:
Schematic Syntax • Attach to a ne
Page 297 and 298:
TPSYNC (Timing Point Synchronizatio
Page 299 and 300:
UCF and NCF Syntax NET “net_name
Page 301 and 302:
Using TPTHRU in a FROM TO Constrain
Page 303 and 304:
TSidentifier (Timing Specification
Page 305 and 306:
Ignoring Paths Note This form is no
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Chapter 4: Xilinx Constraints If yo
Page 315 and 316:
Use Low Skew Lines (USELOWSKEWLINES
Page 317 and 318:
VCCAUX (VCCAUX) Architecture Suppor
Page 319 and 320:
Page 321 and 322:
VREF (VREF) The VREF (VREF) constra
Page 323 and 324:
XBLKNM (XBLKNM) Architecture Suppor
Page 325:
Additional Resources Appendix • X
show all

Xilinx Constraints Guide

Create successful ePaper yourself

Delete template?

Save as template?