Protege System Controller Reference Manual

More documents

Recommendations

Info

Selecting a Elevator to Modify Each elevator is assigned a unique door number from 001 to 250. Your system will be limited to specific number of elevators that are defined in the selected profile. For information on profiles refer to the Advanced Programming Section (see page 207). Elevator to modify: EL001 Type the appropriate 3-digit elevator number or use the [] and [] keys to scroll the available elevator numbers. When the desired elevator number appears on the screen, press [ENTER] to program the selected elevator number. The maximum number of elevators that can be programmed is limited by your system's memory and configured profile. Elevator Name If the selected elevator has a name associated (some elevators do not have a name associated with them) the name programming screen will be shown. EL001 Name *Elevator 001 To scroll elevators by name use the [] and [] keys. To modify or enter a new name for the selected elevator use the keypad as explained in section Entering Text and Names (see page 341) and press [ENTER]. By default the elevator name will be prefixed by an '*' this indicates that the name is an editable name in the system. Some elevators do not have names, this is limited by the system memory and the profile configured. General Options General options configure the elevator for various operational modes and functions. EL001 General [--------] To modify options, use the keypad as explained in section Entering Data Options (see page 344). Option 1 – Destination Reporting Mode Enabled • Enabled the elevator will operate in DRM mode allowing only one button to be selected by the user when the present their card. i When using the DRM mode the PRT-PX16 modules that are used for elevator control must have a PRT-PX16-DRI board attached to allow the connection of button feedback inputs. • Disabled the elevator will operate in normal mode with one badge activating the appropriate floor relays for the user. Option 2, 3, 4, 5, 6, 7 and 8 - Reserved • Reserved do not modify Enabling/disabling or modifying the settings of reserved options is not recommended. 144 PRT-CTRL-SE Protege System Controller Reference Manual | PRT-CTRL-SE
Reader Expander The reader expander selection programs the elevator to send the activation of floor information and floor selection to the reader expander programmed. You must also set the port number in the next screen to the appropriate port driving this elevator. EL001 Reader None Use the [1] and [3] keys to scroll the reader expanders that are available and press [ENTER] to select the expander displayed. For more information about the list control data entry refer to the section List Control Data Entry (see page 344). Reader Port The reader port selection programs the elevator to communicate on this port with the expander number selected above. You must also set the reader expander number in the previous screen. EL001 Port None Use the [1] and [3] keys to scroll the reader port and press [ENTER] to select the port displayed. For more information about the list control data entry refer to the section List Control Data Entry (see page 344). Floor Open Time The floor open time configures the amount of time that a floor will be activated for when it has been selected or the amount of time the floor relay will be activated for when the user has presented a card. EL001 Open time: 005 secs To modify the Floor open time (000 to 255 Seconds), use the keypad as explained in section Entering Decimal Numbers (see page 341) and press [ENTER]. Destination Select Time The destination select time configures the amount of time that user has to select a floor when they present their card. EL001 Select time: 005 secs To modify the floor select time (000 to 255 Seconds), use the keypad as explained in section Entering Decimal Numbers (see page 341) and press [ENTER]. Floor Configuration Each floor in an elevator can be assigned options, an unlock schedule and an area. These options configure how the floor will function. You must select the floor to modify for the elevator that you are programming. EL001 Floor to modify: FL001 Type the appropriate 3-digit floor number or use the [] and [] keys to scroll the available floors for the elevator. When the desired floor number appears on the screen, press [ENTER] to program the selected floor. PRT-CTRL-SE Protege System Controller Reference Manual | PRT-CTRL-SE 145
Page 1 and 2:
PRT-CTRL-SE Protege System Controll
Page 3 and 4:
Contents Protege System ___________
Page 5 and 6:
Intercom High Level Interface _____
Page 7 and 8:
DVAC Surgard Trouble Zones ________
Page 9 and 10:
Protege System Introduction This ma
Page 11 and 12:
Menu Tree Menu Reference General op
Page 13 and 14:
7. Bypass 8. System *Main Menu* 7.
Page 15 and 16:
Area Control Area control allows yo
Page 17 and 18:
Force Arming Force arming allows yo
Page 19 and 20:
24HR Disabling The Protege System c
Page 21 and 22:
• Press [MENU, 7] to access the b
Page 23 and 24:
User Programming To access the user
Page 25 and 26:
Access Level 1 End Date Setting the
Page 27 and 28:
User Card Number When user requires
Page 29 and 30:
Option 5 - Automatic Primary Area D
Page 31 and 32:
Menu Group Name If the selected men
Page 33 and 34:
• This option will not operate un
Page 35 and 36:
Menu Group Extra 2 Menu Options All
Page 37 and 38:
Block # Opt 1 Opt 2 Opt 3 Opt 4 Opt
Page 39 and 40:
Page 41 and 42:
Secondary Access Level A secondary
Page 43 and 44:
For this option to work, the Activa
Page 45 and 46:
Selecting an Elevator Group to Modi
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Hex Review To access the hex event
Page 53 and 54:
Modules To access the module progra
Page 55 and 56:
Module Polling Time The polling tim
Page 57 and 58:
Keypad Smoke Detector Reset PGM The
Page 59 and 60:
Option 1 - Unlock Controlled Door
Page 61 and 62:
Selecting a Zone Expander to Modify
Page 63 and 64:
PGM Expander To access the PGM Expa
Page 65 and 66:
Reader Expander To access the Reade
Page 67 and 68:
Option 3 - Multiple Reader Connecte
Page 69 and 70:
Format Sentrax 9000 T2 Description
Page 71 and 72:
Format Apollo 44 Bit Description De
Page 73 and 74:
Reader Port 1 Multi Badge Operation
Page 75 and 76:
• When the option is disabled and
Page 77 and 78:
• Disabled the reader will turn o
Page 79 and 80:
Reader Port 2 Reading Format The re
Page 81 and 82:
Reader Port 2 Reader Options Option
Page 83 and 84:
Option 8 - Arm User Area • Enable
Page 85 and 86:
Option 4 - 8 - Reserved • Reserve
Page 87 and 88:
To view the IP address of the modul
Page 89 and 90:
Analog Channel 1 Update Time When t
Page 91 and 92:
Selecting a Zone to Modify Each zon
Page 93 and 94: Option 4 - Zone Uses 6K8 and 2K2 EO
Page 95 and 96: Zone Fourth Area Assignment The zon
Page 97 and 98: Selecting a Trouble Zone to Modify
Page 99 and 100: Type Fire Loop Power Fault Bell/PGM
Page 101 and 102: Trouble Zone Type Third Area Assign
Page 103 and 104: Automation Control Point An automat
Page 105 and 106: Option 8 - Recycle Zone On Exit Del
Page 107 and 108: Zone Type Automation Options Automa
Page 109 and 110: Option 6 - Toggle Zone Control PGM
Page 111 and 112: Activation Schedule The activation
Page 113 and 114: Area An installation may contain an
Page 115 and 116: Re-Arm Delay Setting the re-arm del
Page 117 and 118: Area Interlock Group Assignment An
Page 119 and 120: Entry Delay PGM Pulse OFF Time The
Page 121 and 122: Disarmed PGM Pulse ON Time The disa
Page 123 and 124: Memory PGM or PGM Group You can ass
Page 125 and 126: Defer PGM Pulse OFF Time The defer
Page 127 and 128: Use this option when multiple areas
Page 129 and 130: • Disabled the area will arm rega
Page 131 and 132: Access Control To access the access
Page 133 and 134: Inside Area The inside area defines
Page 135 and 136: Pre Alarm PGM Pulse OFF Time The pr
Page 137 and 138: Option 2 - Door Open Event When On
Page 139 and 140: Option 4 - Deny Entry if Inside Are
Page 141 and 142: Door Type Name If the selected door
Page 143: Exit Options Exit options for the d
Page 147 and 148: Floor Each floor is assigned a uniq
Page 149 and 150: PGM Number 2 In PGM Group Each PGM
Page 151 and 152: Secondary Keypad Group A secondary
Page 153 and 154: Controlling Services (Starting and
Page 155 and 156: Service Mode The service mode deter
Page 157 and 158: Option 5 - PABX Requires Pause •
Page 159 and 160: Reporting Table With the size of th
Page 161 and 162: Monitor Phone Service To program th
Page 163 and 164: Call Host Attempts The call host at
Page 165 and 166: Reporting Options The Reporting Opt
Page 167 and 168: Poll Time The poll time configures
Page 169 and 170: SIA Level 2 Reporting Service To pr
Page 171 and 172: Option 3 - Reserved • Reserved do
Page 173 and 174: Option 4 - 5 Digit Zone Code • En
Page 175 and 176: Off Hook PGM The off hook PGM is ac
Page 177 and 178: Device Address When the unit is con
Page 179 and 180: Miscellaneous Options The miscellan
Page 181 and 182: Communications Port Speed The commu
Page 183 and 184: ModBUS Area Control Group The area
Page 185 and 186: Data Options The data configure var
Page 187 and 188: Validation Mode The Validation Mode
Page 189 and 190: Intercom 2 Address The intercom 2 a
Page 191 and 192: Intercom Access PGM The Intercom Ac
Page 193 and 194: Reporting Protocol The reporting pr
Page 195 and 196:
Secondary Port The Secondary port c
Page 197 and 198:
Enabling/disabling or modifying the
Page 199 and 200:
Link Me (IO) The Link Me (IO) Servi
Page 201 and 202:
General Options The general options
Page 203 and 204:
Telephone Numbers To access the tel
Page 205 and 206:
Dial Attempt Number Phone Number Di
Page 207 and 208:
Dial Attempt Number Phone Number Di
Page 209 and 210:
Network Online Module View Viewing
Page 211 and 212:
• Pressing the [] key will displa
Page 213 and 214:
Zone Status Display When the zone i
Page 215 and 216:
Door Control and Status Display Eac
Page 217 and 218:
Controlling Functions (Starting and
Page 219 and 220:
Logic Action The logic action deter
Page 221 and 222:
OFF ON ON ON ON OFF • XOR Follow
Page 223 and 224:
The pulse on action will arm the ar
Page 225 and 226:
Enabled Control PGM Enabled Control
Page 227 and 228:
Heating Stage 2 PGM The heat 2 PGM
Page 229 and 230:
Register Offset Register Function 8
Page 231 and 232:
Page 233 and 234:
Function Mode The function mode det
Page 235 and 236:
Cool On PGM The cool on PGM is acti
Page 237 and 238:
Floor Temperature Register The floo
Page 239 and 240:
Page 241 and 242:
Ripple Off Time The ripple off time
Page 243 and 244:
Door Action The action determines w
Page 245 and 246:
Door Control Mode The control mode
Page 247 and 248:
Virtual Door Forced Open Zone When
Page 249 and 250:
Function Mode The function mode det
Page 251 and 252:
• Pulse On The pulse on action wi
Page 253 and 254:
Register Counter • Protege System
Page 255 and 256:
Average The average function takes
Page 257 and 258:
Compare Register Base This is the f
Page 259 and 260:
Automation Name If the selected aut
Page 261 and 262:
• Disabled the C-Bus processing w
Page 263 and 264:
Character A a Function Show the AM/
Page 265 and 266:
Host Verify ID The host verify ID i
Page 267 and 268:
Panel Options 2 Option 1 - Short of
Page 269 and 270:
System Controller Restart in Bios M
Page 271 and 272:
Parity Start Block 1 to 4 The parit
Page 273 and 274:
The second setting to edit is the s
Page 275 and 276:
in Area Warehouse Press [ENTER] to
Page 277 and 278:
The display will show the door lock
Page 279 and 280:
Time The time menu allows a keypad
Page 281 and 282:
Selecting an Schedule Entry to Modi
Page 283 and 284:
Option 5 - Friday • Enabled the p
Page 285 and 286:
Holiday Start Date Program a starti
Page 287 and 288:
Daylight Savings End Month The end
Page 289 and 290:
CP001:01 T-Zone is not BYPASSED •
Page 291 and 292:
Reporting Tables Reporting tables a
Page 293 and 294:
Zone Number Contact ID Code Reporti
Page 295 and 296:
In the above table a reporting code
Page 297 and 298:
Page 299 and 300:
In the above table a reporting code
Page 301 and 302:
Analog Input/Output Expander The An
Page 303 and 304:
Page 305 and 306:
Analog Input/Output Expander The An
Page 307 and 308:
Zone Number Alarm Code Restore Code
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
16 PGM Output Expander The 16 PGM O
Page 317 and 318:
Page 319 and 320:
Reporting Codes Custom reporting co
Page 321 and 322:
There are various options that can
Page 323 and 324:
Zone Number Description Type Group
Page 325 and 326:
Zone Number Description Type Group
Page 327 and 328:
Description Number User Names 2000
Page 329 and 330:
Description PGM Names 16 Floor Name
Page 331 and 332:
School Profile The school profile i
Page 333 and 334:
Description Number Areas 128 Access
Page 335 and 336:
Description Area Names 64 Access Le
Page 337 and 338:
Description Number Floor Names 0 El
Page 339 and 340:
Object Notation When selecting an a
Page 341 and 342:
System Type ZNT ATT DRT DTT AGT MGT
Page 343 and 344:
Programming the name or text value
Page 345 and 346:
List Data Entry List data entry is
Page 347 and 348:
Conversion When programming the Pro
Page 349 and 350:
ASCII Conversion In some cases it i
Page 351 and 352:
Contact Integrated Control Technolo
show all

Protege System Controller Reference Manual

Create successful ePaper yourself

Delete template?

Save as template?