Protege System Controller Reference Manual

More documents

Recommendations

Info

• Not Pulse Off The not pulse off action will unlock the door only when the input one has transitioned from an ON to an OFF state. The output will not be modified further from this state and will not be modified if it is turned ON by another function. Input One Output LOCKED Input One PGM Input one selects the input source to the door control process that is being configured. All door control functions use at least one input source. Input one must be programmed with a valid input source, if an input source is selected that is not valid when the function is started an error will be generated and the function suspended. An input source can be a PGM (Programmable Output). FN001 Input one pgm: --000:00 To modify the input PGM, use the settings as explained in section Entering PGM and PGM Groups (see page 345). Control Door The control door selects the door to control as a result of the action being performed by the programmable function. To control a door group leave the control door option set to none and proceed to the Control Door Group entry screen. Selecting both a door and a door group will result in only the door being controlled and the door group being ignored. FN001 Door None Use the [1] and [3] keys to scroll the action types until you reach the door that you want to control and then press [ENTER] to proceed to the next programmable option for the door control function. For more information about the list control data entry refer to the section List Control Data Entry (see page 344). Control Door Group The control door group selects the area group to control as a result of the action being performed by the programmable function. To control a door leave the control door group set at none and program a door in the control door section. Programming a door and a door group will result in the door group not being used. FN001 Door Grp None Use the [1] and [3] keys to scroll the door groups until you reach the required group and then press [ENTER] to proceed to the next programmable option for the door control function. For more information about the list control data entry refer to the section List Control Data Entry (see page 344). 244 PRT-CTRL-SE Protege System Controller Reference Manual | PRT-CTRL-SE
Door Control Mode The control mode selects how the door will be controlled in the control door or control door group setting. This allows a door to be unlocked for the door unlock time, unlock latched or unlocked in the fire alarm mode. FN001 Door Mode Menu Timed Use the [1] and [3] keys to scroll the door control mode until you reach the setting that you want to use and then press [ENTER] to proceed to the next programmable option for the door control function. For more information about the list control data entry refer to the section List Control Data Entry (see page 344). Door Mode Menu Timed Menu Latched Fire Control Lockdown Lockdown (Entry Allowed) Lockdown (Exit Allowed) Lockdown (Entry and Exit Allowed) Description The Door will be unlocked for the door unlock time that is programmed for the door. Use this mode when you want to unlock the door for unlock time. The door will lock after the unlock time has expired. The door will be latched in the unlocked state and will remain unlocked until controlled from: A LCD Keypad Protege System Management Suite Scheduled Action Area Status A Programmable function. The door will be latched in the fire control unlock state and will remain unlocked until controlled from: A LCD Keypad Protege System Management Suite A Programmable function that is programmed to deactivate the fire alarm control. Door Lockdown will be started for the door or door group and will remain Protege an LCD Keypad or when the PGM input goes off if the function is operating in a Test and Follow mode. Door Lockdown with Entry Allowed will be started for the door or door group and will remain locked down until it is cancelled from the Protege System Management Suite, an LCD Keypad or when the PGM input goes off if the function is operating in a Test and Follow mode. Door Lockdown with Exit Allowed will be started for the door or door group and will remain locked down until it is cancelled from the Protege System Management Suite, an LCD Keypad or when the PGM input goes off if the function is operating in a Test and Follow mode. Door Lockdown with Entry and Exit Allowed will be started for the door or door group and will remain locked down until it is cancelled from the Protege System Management Suite, an LCD Keypad or when the PGM input goes off if the function is operating in a Test and Follow mode. Virtual Door Function To program the virtual door function ensure that the function you have selected is halted. Select the function type selection screen as shown below for the Virtual Door. FN001 Func Type Virtual Door Use the [1] and [3] keys to scroll the function types until you reach the door control selection and press [ENTER] to select the function type displayed and proceed to the next programmable option for the door control function. For more information about the list control data entry refer to the section List Control Data Entry (see page 344). PRT-CTRL-SE Protege System Controller Reference Manual | PRT-CTRL-SE 245
Page 1 and 2:
PRT-CTRL-SE Protege System Controll
Page 3 and 4:
Contents Protege System ___________
Page 5 and 6:
Intercom High Level Interface _____
Page 7 and 8:
DVAC Surgard Trouble Zones ________
Page 9 and 10:
Protege System Introduction This ma
Page 11 and 12:
Menu Tree Menu Reference General op
Page 13 and 14:
7. Bypass 8. System *Main Menu* 7.
Page 15 and 16:
Area Control Area control allows yo
Page 17 and 18:
Force Arming Force arming allows yo
Page 19 and 20:
24HR Disabling The Protege System c
Page 21 and 22:
• Press [MENU, 7] to access the b
Page 23 and 24:
User Programming To access the user
Page 25 and 26:
Access Level 1 End Date Setting the
Page 27 and 28:
User Card Number When user requires
Page 29 and 30:
Option 5 - Automatic Primary Area D
Page 31 and 32:
Menu Group Name If the selected men
Page 33 and 34:
• This option will not operate un
Page 35 and 36:
Menu Group Extra 2 Menu Options All
Page 37 and 38:
Block # Opt 1 Opt 2 Opt 3 Opt 4 Opt
Page 39 and 40:
Page 41 and 42:
Secondary Access Level A secondary
Page 43 and 44:
For this option to work, the Activa
Page 45 and 46:
Selecting an Elevator Group to Modi
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Hex Review To access the hex event
Page 53 and 54:
Modules To access the module progra
Page 55 and 56:
Module Polling Time The polling tim
Page 57 and 58:
Keypad Smoke Detector Reset PGM The
Page 59 and 60:
Option 1 - Unlock Controlled Door
Page 61 and 62:
Selecting a Zone Expander to Modify
Page 63 and 64:
PGM Expander To access the PGM Expa
Page 65 and 66:
Reader Expander To access the Reade
Page 67 and 68:
Option 3 - Multiple Reader Connecte
Page 69 and 70:
Format Sentrax 9000 T2 Description
Page 71 and 72:
Format Apollo 44 Bit Description De
Page 73 and 74:
Reader Port 1 Multi Badge Operation
Page 75 and 76:
• When the option is disabled and
Page 77 and 78:
• Disabled the reader will turn o
Page 79 and 80:
Reader Port 2 Reading Format The re
Page 81 and 82:
Reader Port 2 Reader Options Option
Page 83 and 84:
Option 8 - Arm User Area • Enable
Page 85 and 86:
Option 4 - 8 - Reserved • Reserve
Page 87 and 88:
To view the IP address of the modul
Page 89 and 90:
Analog Channel 1 Update Time When t
Page 91 and 92:
Selecting a Zone to Modify Each zon
Page 93 and 94:
Option 4 - Zone Uses 6K8 and 2K2 EO
Page 95 and 96:
Zone Fourth Area Assignment The zon
Page 97 and 98:
Selecting a Trouble Zone to Modify
Page 99 and 100:
Type Fire Loop Power Fault Bell/PGM
Page 101 and 102:
Trouble Zone Type Third Area Assign
Page 103 and 104:
Automation Control Point An automat
Page 105 and 106:
Option 8 - Recycle Zone On Exit Del
Page 107 and 108:
Zone Type Automation Options Automa
Page 109 and 110:
Option 6 - Toggle Zone Control PGM
Page 111 and 112:
Activation Schedule The activation
Page 113 and 114:
Area An installation may contain an
Page 115 and 116:
Re-Arm Delay Setting the re-arm del
Page 117 and 118:
Area Interlock Group Assignment An
Page 119 and 120:
Entry Delay PGM Pulse OFF Time The
Page 121 and 122:
Disarmed PGM Pulse ON Time The disa
Page 123 and 124:
Memory PGM or PGM Group You can ass
Page 125 and 126:
Defer PGM Pulse OFF Time The defer
Page 127 and 128:
Use this option when multiple areas
Page 129 and 130:
• Disabled the area will arm rega
Page 131 and 132:
Access Control To access the access
Page 133 and 134:
Inside Area The inside area defines
Page 135 and 136:
Pre Alarm PGM Pulse OFF Time The pr
Page 137 and 138:
Option 2 - Door Open Event When On
Page 139 and 140:
Option 4 - Deny Entry if Inside Are
Page 141 and 142:
Door Type Name If the selected door
Page 143 and 144:
Exit Options Exit options for the d
Page 145 and 146:
Reader Expander The reader expander
Page 147 and 148:
Floor Each floor is assigned a uniq
Page 149 and 150:
PGM Number 2 In PGM Group Each PGM
Page 151 and 152:
Secondary Keypad Group A secondary
Page 153 and 154:
Controlling Services (Starting and
Page 155 and 156:
Service Mode The service mode deter
Page 157 and 158:
Option 5 - PABX Requires Pause •
Page 159 and 160:
Reporting Table With the size of th
Page 161 and 162:
Monitor Phone Service To program th
Page 163 and 164:
Call Host Attempts The call host at
Page 165 and 166:
Reporting Options The Reporting Opt
Page 167 and 168:
Poll Time The poll time configures
Page 169 and 170:
SIA Level 2 Reporting Service To pr
Page 171 and 172:
Option 3 - Reserved • Reserved do
Page 173 and 174:
Option 4 - 5 Digit Zone Code • En
Page 175 and 176:
Off Hook PGM The off hook PGM is ac
Page 177 and 178:
Device Address When the unit is con
Page 179 and 180:
Miscellaneous Options The miscellan
Page 181 and 182:
Communications Port Speed The commu
Page 183 and 184:
ModBUS Area Control Group The area
Page 185 and 186:
Data Options The data configure var
Page 187 and 188:
Validation Mode The Validation Mode
Page 189 and 190:
Intercom 2 Address The intercom 2 a
Page 191 and 192:
Intercom Access PGM The Intercom Ac
Page 193 and 194: Reporting Protocol The reporting pr
Page 195 and 196: Secondary Port The Secondary port c
Page 197 and 198: Enabling/disabling or modifying the
Page 199 and 200: Link Me (IO) The Link Me (IO) Servi
Page 201 and 202: General Options The general options
Page 203 and 204: Telephone Numbers To access the tel
Page 205 and 206: Dial Attempt Number Phone Number Di
Page 207 and 208: Dial Attempt Number Phone Number Di
Page 209 and 210: Network Online Module View Viewing
Page 211 and 212: • Pressing the [] key will displa
Page 213 and 214: Zone Status Display When the zone i
Page 215 and 216: Door Control and Status Display Eac
Page 217 and 218: Controlling Functions (Starting and
Page 219 and 220: Logic Action The logic action deter
Page 221 and 222: OFF ON ON ON ON OFF • XOR Follow
Page 223 and 224: The pulse on action will arm the ar
Page 225 and 226: Enabled Control PGM Enabled Control
Page 227 and 228: Heating Stage 2 PGM The heat 2 PGM
Page 229 and 230: Register Offset Register Function 8
Page 233 and 234: Function Mode The function mode det
Page 235 and 236: Cool On PGM The cool on PGM is acti
Page 237 and 238: Floor Temperature Register The floo
Page 241 and 242: Ripple Off Time The ripple off time
Page 243: Door Action The action determines w
Page 247 and 248: Virtual Door Forced Open Zone When
Page 249 and 250: Function Mode The function mode det
Page 251 and 252: • Pulse On The pulse on action wi
Page 253 and 254: Register Counter • Protege System
Page 255 and 256: Average The average function takes
Page 257 and 258: Compare Register Base This is the f
Page 259 and 260: Automation Name If the selected aut
Page 261 and 262: • Disabled the C-Bus processing w
Page 263 and 264: Character A a Function Show the AM/
Page 265 and 266: Host Verify ID The host verify ID i
Page 267 and 268: Panel Options 2 Option 1 - Short of
Page 269 and 270: System Controller Restart in Bios M
Page 271 and 272: Parity Start Block 1 to 4 The parit
Page 273 and 274: The second setting to edit is the s
Page 275 and 276: in Area Warehouse Press [ENTER] to
Page 277 and 278: The display will show the door lock
Page 279 and 280: Time The time menu allows a keypad
Page 281 and 282: Selecting an Schedule Entry to Modi
Page 283 and 284: Option 5 - Friday • Enabled the p
Page 285 and 286: Holiday Start Date Program a starti
Page 287 and 288: Daylight Savings End Month The end
Page 289 and 290: CP001:01 T-Zone is not BYPASSED •
Page 291 and 292: Reporting Tables Reporting tables a
Page 293 and 294: Zone Number Contact ID Code Reporti
Page 295 and 296:
In the above table a reporting code
Page 297 and 298:
Zone Number Contact ID Code Reporti
Page 299 and 300:
In the above table a reporting code
Page 301 and 302:
Analog Input/Output Expander The An
Page 303 and 304:
Zone Number Contact ID Code Reporti
Page 305 and 306:
Analog Input/Output Expander The An
Page 307 and 308:
Zone Number Alarm Code Restore Code
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
16 PGM Output Expander The 16 PGM O
Page 317 and 318:
Page 319 and 320:
Reporting Codes Custom reporting co
Page 321 and 322:
There are various options that can
Page 323 and 324:
Zone Number Description Type Group
Page 325 and 326:
Zone Number Description Type Group
Page 327 and 328:
Description Number User Names 2000
Page 329 and 330:
Description PGM Names 16 Floor Name
Page 331 and 332:
School Profile The school profile i
Page 333 and 334:
Description Number Areas 128 Access
Page 335 and 336:
Description Area Names 64 Access Le
Page 337 and 338:
Description Number Floor Names 0 El
Page 339 and 340:
Object Notation When selecting an a
Page 341 and 342:
System Type ZNT ATT DRT DTT AGT MGT
Page 343 and 344:
Programming the name or text value
Page 345 and 346:
List Data Entry List data entry is
Page 347 and 348:
Conversion When programming the Pro
Page 349 and 350:
ASCII Conversion In some cases it i
Page 351 and 352:
Contact Integrated Control Technolo
show all

Protege System Controller Reference Manual

Create successful ePaper yourself

Delete template?

Save as template?