NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

Honeywell Multi-purpose Control Application 73
6.6.3 Basic parameters (Control keypad: Menu M2 G2.1)
Code Parameter Min Max Unit Default Cust ID Note
P2.1.1 Min frequency 0,00 Par. 2.1.2 Hz 0,00 101
P2.1.2 Max frequency Par. 2.1.1 320,00 Hz 50,00 102
P2.1.3 Acceleration time 1 0,1 3000,0 s 3,0 103
P2.1.4 Deceleration time 1 0,1 3000,0 s 3,0 104
P2.1.5 Current limit 0,1 x I H 2 x I H A I L 107
P2.1.6
Nominal voltage of
the motor
180 690 V
NX2: 230V
NX5: 400V
NX6: 690V
110
NOTE: If f max > than the
motor synchronous speed,
check suitability for motor
and drive system
P2.1.7
Nominal frequency
Check the rating plate of
8,00 320,00 Hz 50,00 111
of the motor
the motor
P2.1.8
The default applies for a 4-
Nominal speed of
24 20 000 rpm 1440 112 pole motor and a nominal
the motor
size frequency drive.
P2.1.9
Nominal current of
Check the rating plate of
0,1 x I
the motor
H 2 x I H A I H 113
the motor.
P2.1.10 Motor cosϕ 0,30 1,00 0,85 120
Check the rating plate of
the motor
P2.1.11 I/O Reference 0 15/16 0 117
0=AI1
1=AI2
2=AI1+AI2
3=AI1-AI2
4=AI2-AI1
5=AI1xAI2
6=AI1 Joystick
7=AI2 Joystick
8=Keypad
9=Fieldbus
10=Motor potentiometer
11=AI1, AI2 minimum
12=AI1, AI2 maximum
13=Max frequency
14=AI1/AI2 selection
15=Encoder 1
16=Encoder 2 (NXP only)
0=AI1
1=AI2
2=AI1+AI2
3=AI1-AI2
P2.1.12
Keypad control
4=AI2-AI1
0 9 8 121
reference
5=AI1xAI2
6=AI1 Joystick
7=AI2 Joystick
8=Keypad
9=Fieldbus
P2.1.13
Fieldbus control
reference
0 9 9 122 See par. 2.1.12
P2.1.14
Jogging speed
reference
0,00 Par. 2.1.2 Hz 5,00 124 See ID413.
P2.1.15 Preset speed 1 0,00 Par. 2.1.2 Hz 10,00 105 Multi-step speed 1
P2.1.16 Preset speed 2 0,00 Par. 2.1.2 Hz 15,00 106 Multi-step speed 2
P2.1.17 Preset speed 3 0,00 Par. 2.1.2 Hz 20,00 126 Multi-step speed 3
P2.1.18 Preset speed 4 0,00 Par. 2.1.2 Hz 25,00 127 Multi-step speed 4
P2.1.19 Preset speed 5 0,00 Par. 2.1.2 Hz 30,00 128 Multi-step speed 5
P2.1.20 Preset speed 6 0,00 Par. 2.1.2 Hz 40,00 129 Multi-step speed 6
P2.1.21 Preset speed 7 0,00 Par. 2.1.2 Hz 50,00 130 Multi-step speed 7
Table 6-5. Basic parameters G2.1
Automation and Control Solutions
Honeywell
Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North 35 Dynamic Drive
Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1
MIV 4Z9
www.honeywell.com