NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...
NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...
NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
88 Multi-purpose Control Application Honeywell<br />
6.6.9.1 NXP drives: Closed Loop parameters (Control keypad: Menu M2 G2.6.27)<br />
Code Parameter Min Max Unit Default Cust ID Note<br />
P2.6.27.1<br />
Magnetizing<br />
current<br />
0,00 100,00 A 0,00 612 If zero internally calculated<br />
P2.6.27.2<br />
Speed control P<br />
gain<br />
1 1000 30 613<br />
P2.6.27.3<br />
Speed control I<br />
Negative value uses 1 ms<br />
-32000 3200,0 ms 100,0 614<br />
time<br />
accuracy instead of 0,1 ms<br />
P2.6.27.5<br />
Acceleration<br />
compensation<br />
0,00 300,00 s 0,00 626<br />
P2.6.27.6 Slip adjust 0 500 % 75 619<br />
P2.6.27.7<br />
Magnetizing<br />
current at start<br />
0 I L A 0,00 627<br />
P2.6.27.8<br />
Magnetizing time<br />
at start<br />
0 32000 ms 0 628<br />
P2.6.27.9<br />
0-speed time at<br />
start<br />
0 32000 ms 100 615<br />
P2.6.27.10<br />
0-speed time at<br />
stop<br />
0 32000 ms 100 616<br />
P2.6.27.11 Start-up torque 0 3 0 621<br />
0=Not used<br />
1=Torque memory<br />
2=Torque reference<br />
3=Start-up torque fwd/rev<br />
P2.6.27.12<br />
Start-up torque<br />
FWD<br />
–300,0 300,0 % 0,0 <strong>63</strong>3<br />
P2.6.27.13<br />
Start-up torque<br />
REV<br />
–300,0 300,0 % 0,0 <strong>63</strong>4<br />
P2.6.27.15 Encoder filter time 0,0 100,0 ms 0,0 618<br />
P2.6.27.17<br />
Current control<br />
P gain<br />
0,00 100,00 % 40,00 617<br />
P2.6.27.19<br />
Generator power<br />
limit<br />
0,0 300,0 % 300,0 1290<br />
P2.6.27.20<br />
Motoring power<br />
limit<br />
0,0 300,0 % 300,0 1289<br />
P2.6.27.21<br />
Negative torque<br />
limit<br />
0,0 300,0 % 300,0 645<br />
P2.6.27.22<br />
Positive torque<br />
limit<br />
0,0 300,0 % 300,0 646<br />
P2.6.27.23 Flux off delay -1 32000 s 0 1402 -1=Always<br />
P2.6.27.24 Stop state flux 0,0 150,0 % 100,0 1401<br />
P2.6.27.25 SPC f1 point 0,00 320,00 Hz 0,00 1301<br />
P2.6.27.26 SPC f0 point 0,00 320,00 Hz 0,00 1300<br />
P2.6.27.27 SPC Kp f0 0 1000 % 100 1299<br />
P2.6.27.28 SPC Kp FWP 0 1000 % 100 1298<br />
P2.6.27.29<br />
SPC torque<br />
minimum<br />
0 400,0 % 0,0 1296<br />
P2.6.27.30<br />
SPC torque<br />
minimum Kp<br />
0 1000 % 100 1295<br />
P2.6.27.31 SPC Kp TC torque 0 1000 ms 0 1297<br />
P2.6.27.32 Flux reference 0,0 500,0 % 100,0 1250<br />
P2.6.27.33<br />
Speed error filter<br />
TC<br />
0 1000 ms 0 1311<br />
Table 6-26. Closed Loop motor control parameters (G2.6.4)<br />
Automation and Control Solutions<br />
Honeywell<br />
Honeywell Limited-Honeywell Limitée<br />
1985 Douglas Drive North 35 Dynamic Drive<br />
Golden Valley, MIN 55422 Scarborough, Ontario <strong>63</strong>-<strong>2600</strong>-1<br />
MIV 4Z9<br />
www.honeywell.com
Change language