NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

More documents

Recommendations

Info

178 Description of Parameters Honeywell 641 Torque reference selection 6 (2.10.3) Defines the source for torque reference. 0 Not used 1 Analogue input 1 2 Analogue input 2 3 Analogue input 3 4 Analogue input 4 5 Analogue input 1 (joystick) 6 Analogue input 2 (joystick) 7 From keypad, parameter R3.5 8 Fieldbus torque reference 642 Torque reference scaling, maximum value 6 (2.10.4) 643 Torque reference scaling, minimum value 6 (2.10.5) Scale the custom minimum and maximum levels for analogue inputs within -300,0…300,0%. 644 Torque speed limit, NXS 6 (2.10.6) With this parameter the maximum frequency for the torque control can be selected. 0 Maximum frequency 1 Selected frequency reference 2 Preset speed 7 NXP drives have more selections for this parameter. See page 204. 645 Negative torque limit 6 (2.6.27.21) 646 Positive torque limit 6 (2.6.27.22) Defines the torque limit for positive and negative directions. 649 PMS motor shaft position 6 (2.6.28.4) Identified zero shaft position when using absolute encoder for PMS motor. 650 Motor type 6 (2.6.28.1) Select used motor type with this parameter. 0 Induction motor 1 Permanent magnet synchronous motor 654 Enable Rs identification 6 (2.6.28.5) Stator resistance identification at start. 0 No 1 Yes 655 Modulator index limit This parameter can be used to increase motor voltage in field weakening area. Automation and Control Solutions Honeywell Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1 MIV 4Z9 www.honeywell.com
Honeywell Description of Parameters 179 656 Load drooping time This function is used in order to achieve a dynamic speed drooping because of changing load. The parameter defines the time during which the speed is restored to the level it was before the load increase. 662 Measured voltage drop 6 (2.6.29.16) The measured voltage drop at stator resistance between two phases with the nominal current of the motor. 665 Ir: Add generator scale 6 (2.6.29.19) Scaling factor for generator side IR-compensation. 667 Ir: Add motoring scale 6 (2.6.29.20) Scaling factor for motoring side IR-compensation. 668 IU Offset 6 (2.6.29.21) 669 IV Offset 6 (2.6.29.22) 670 IW Offset 6 (2.6.29.23) Offset values for phase current measurement. Automation and Control Solutions Honeywell Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1 MIV 4Z9 www.honeywell.com
Page 1:
NX Series Constant and Variable Tor
Page 4 and 5:
CONTENTS NX USER’S MANUAL INDEX 1
Page 6 and 7:
NX User's Manual Index 1. SAFETY...
Page 8 and 9:
1 6(110) Safety 1. SAFETY ONLY A CO
Page 10 and 11:
8(110) DIRECTIVES 2. DIRECTIVES 2.1
Page 12 and 13:
10(110) DIRECTIVES We Manufacturer'
Page 14 and 15:
3 12(110) Receipt of shipment We Ma
Page 16 and 17:
3 14(110) Receipt of shipment 3.3 M
Page 18 and 19:
16(110) Technical data The control
Page 20 and 21:
18(110) Technical data 4.2.2 NX_6 -
Page 22 and 23:
20(110) Technical data 4.3 Brake re
Page 24 and 25:
22(110) Technical data 4.4 Technica
Page 26 and 27:
5 24(110) Installation 5. INSTALLAT
Page 28 and 29:
5 26(110) Installation W2 H4 D1 D2
Page 30 and 31:
5 28(110) Installation W4 W2 H7 H6
Page 32 and 33:
5 30(110) Installation Ø D1 D2 H4
Page 34 and 35:
5 32(110) Installation W4 Type plat
Page 36 and 37:
5 34(110) Installation 5.2 Cooling
Page 38 and 39:
5 36(110) Installation 5.3 Power lo
Page 40 and 41:
5 38(110) Cabling and connections 5
Page 42 and 43:
40(110) Cabling and connections 6.
Page 44 and 45:
42(110) Cabling and connections 6.1
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
52(110) Cabling and connections Fig
Page 56 and 57:
Page 58 and 59:
56(110) Cabling and connections Mai
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
64(110) Cabling and connections 10V
Page 68 and 69:
66(110) Cabling and connections OPT
Page 70 and 71:
68(110) Cabling and connections Jum
Page 72 and 73:
7 70(110) Control keypad 4 5 6 READ
Page 74 and 75:
7 72(110) Control keypad 7.2 Keypad
Page 76 and 77:
7 74(110) Control keypad RE ADY I/O
Page 78 and 79:
7 76(110) Control keypad 7.3.2 Para
Page 80 and 81:
7 78(110) Control keypad 7.3.3 Keyp
Page 82 and 83:
7 80(110) Control keypad NOTE! Ther
Page 84 and 85:
7 82(110) Control keypad 7.3.4.2 Fa
Page 86 and 87:
7 84(110) Control keypad 50 Analog
Page 88 and 89:
7 86(110) Control keypad 7.3.6 Syst
Page 90 and 91:
7 88(110) Control keypad T6.8.2.2 C
Page 92 and 93:
7 90(110) Control keypad STOP I/Ote
Page 94 and 95:
7 92(110) Control keypad Automatic
Page 96 and 97:
7 94(110) Control keypad Note! Stor
Page 98 and 99:
7 96(110) Control keypad Default pa
Page 100 and 101:
7 98(110) Control keypad READY READ
Page 102 and 103:
7 100(110) Control keypad STOP READ
Page 104 and 105:
7 102(110) Control keypad READY REA
Page 106 and 107:
7 104(110) Control keypad 7.4 Furth
Page 108 and 109:
106(110) Commissioning 6 Connect th
Page 110 and 111:
108(110) Fault tracing 9. FAULT TRA
Page 112:
110(110) Fault tracing 43 Encoder f
Page 115:
NX Series Constant and Variable Tor
Page 118 and 119:
2 Honeywell ABOUT THE "All in One"
Page 120 and 121:
4 Honeywell 9.1 External brake cont
Page 122 and 123:
6 Basic Application Honeywell 1.2 C
Page 124 and 125:
8 Basic Application Honeywell 1.4 B
Page 126 and 127:
10 Basic Application Honeywell 1.4.
Page 128 and 129:
12 Standard Application Honeywell 2
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
22 Local/Remote Control Application
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
36 Multi-step Speed Application Hon
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
48 PID Control Application Honeywel
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
62 Multi-purpose Control Applicatio
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
96 Pump and Fan Control Application
Page 214 and 215:
98 Pump and Fan Control Application
Page 216 and 217:
100 Pump and Fan Control Applicatio
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
122 Description of Parameters Honey
Page 240 and 241:
Page 242 and 243:
Page 244 and 245: 128 Description of Parameters Honey
Page 326 and 327: 210 Appendices Honeywell 9. APPENDI
Page 328 and 329: 212 Appendices Honeywell 9.2 Closed
Page 330: Automation and Control Solutions Ho
show all

NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

Create successful ePaper yourself

Delete template?

Save as template?