NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

Honeywell Description of Parameters 165
461 Autochange 4/Auxiliary drive 4 control 7 (2.3.1.30)
Control signal for autochange/auxiliary drive 4. If three (or more) auxiliary drives are
used, we recommend to connect nr 3 and 4, too, to a relay output. Since the OPT-A2
board only has two relay outputs it is advisable to purchase an I/O expander board with
extra relay outputs (e.g. OPT-B5).
462 Autochange 5 control 7 (2.3.1.31)
Control signal for autochange drive 5.
463 Analogue input supervision limit 67 (2.3.3.22, 2.3.1.22)
The selected analogue input signal goes beyond the set supervision limits (see
parameters ID372, ID373 and ID374).
464 Analogue output 1 signal selection 234567 (2.3.1, 2.3.5.1, 2.3.3.1)
Connect the AO1 signal to the analogue output of your choice with this parameter. For
more information about the TTF programming method, see chapter 6.4.
471 Analogue output 2 signal selection 234567 (2.3.12, 2.3.22, 2.3.6.1, 2.3.4.1)
Connect the AO2 signal to the analogue output of your choice with this parameter. For
more information about the TTF programming method, see chapter 6.4.
472 Analogue output 2 function 234567 (2.3.13, 2.3.23, 2.3.6.2, 2.3.4.2)
473 Analogue output 2 filter time 234567 (2.3.14, 2.3.24, 2.3.6.3, 2.3.4.3)
474 Analogue output 2 inversion 234567 (2.3.15, 2.3.25, 2.3.6.4, 2.3.4.4)
475 Analogue output 2 minimum 234567 (2.3.16, 2.3.26, 2.3.6.5, 2.3.4.5)
476 Analogue output 2 scaling 234567 (2.3.17, 2.3.27, 2.3.6.6, 2.3.4.6)
For more information on these five parameters, see the corresponding parameters for
the analogue output 1 on pages 138 to 139.
477 Analogue output 2 offset 67 (2.3.6.7, 2.3.4.7)
Add –100.0 to 100.0% to the analogue output.
478 Analogue output 3, signal selection 67 (2.3.7.1, 2.3.5.1)
See ID464.
479 Analogue output 3, function 67 (2.3.7.2, 2.3.5.2)
See ID307.
480 Analogue output 3, filter time 67 (2.3.7.3, 2.3.5.3)
See ID308.
481 Analogue output 3 inversion 67 (2.3.7.4, 2.3.5.4)
See ID309.
482 Analogue output 3 minimum 67 (2.3.7.5, 2.3.5.5)
See ID310.
483 Analogue output 3 scaling 67 (2.3.7.6, 2.3.5.6)
See ID311.
Automation and Control Solutions
Honeywell
Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North 35 Dynamic Drive
Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1
MIV 4Z9
www.honeywell.com