NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

Honeywell Multi-purpose Control Application 77
6.6.4.7 Digital inputs (Control keypad: Menu M2 G2.2.4)
Code Parameter Min Default Cust ID Note
P2.2.7.1 Start signal 1 0 A.1 403
P2.2.7.2 Start signal 2 0 A.2 404
P2.2.7.3 Run enable 0 0.2 407 Motor start enabled (cc)
P2.2.7.4 Reverse 0 0.1 412
P2.2.7.5 Preset speed 1 0 0.1 419
P2.2.7.6 Preset speed 2 0 0.1 420
P2.2.7.7 Preset speed 3 0 0.1 421
P2.2.7.8
Motor potentiometer
reference DOWN
0 0.1 417
P2.2.7.9
Motor potentiometer
reference UP
0 0.1 418
Direction forward (oc)
Direction reverse (cc)
See preset speeds in Basic
Parameters (G2.1)
Mot.pot. reference decreases
(cc)
Mot.pot. reference increases
(cc)
P2.2.7.10 Fault reset 0 0.1 414 All faults reset (cc)
P2.2.7.11 External fault (close) 0 0.1 405 Ext. fault displayed (cc)
P2.2.7.12 External fault (open) 0 0.2 406 Ext. fault displayed (oc)
P2.2.7.13 Acc/Dec time selection 0 0.1 408
Acc/Dec time 1 (oc)
Acc/Dec time 2 (cc)
P2.2.7.14 Acc/Dec prohibit 0 0.1 415 Acc/Dec prohibited (cc)
P2.2.7.15 DC braking 0 0.1 416 DC braking active (cc)
P2.2.7.16 Jogging speed 0 A.4 413
Jogging speed selected for
frequency reference (cc)
P2.2.7.17 AI1/AI2 selection 0 0.1 422
P2.2.7.18 Control from I/O terminal 0 0.1 409
Force control place to I/O
terminal (cc)
P2.2.7.19 Control from keypad 0 0.1 410
Force control place to
keypad (cc)
P2.2.7.20 Control from fieldbus 0 0.1 411
Force control place to
fieldbus (cc)
P2.2.7.21
Parameter set 1/set 2
Closed cont.=Set 2 is used
0 0.1 496
selection
Open cont.=Set 1 is used
P2.2.7.22 Motor control mode 1/2 0 0.1 164
Closed cont.=Mode 2 is used
Open cont.=Mode 1 is used
See par 2.6.1, 2.6.12
NXP drives only
P2.2.7.23 Cooling monitor 0 0.2 750 Used with liquid-cooled unit
P2.2.7.24
External brake
Monitoring signal from
0 0.2 1210
acknowledge
mechanical brake
P2.2.7.25 Prevention of startup 0 0.2 1420 Safety switch input
P2.2.7.26 Enable inching 0 0.1 532 Enables Inching function
P2.2.7.27 Inching reference 1 0 0.1 530
Inching reference 1. This will
start the drive
P2.2.7.28 Inching reference 2 0 0.1 531
Inching reference 2. This will
start the drive
P2.2.7.29 Reset encoder counter 0 0.1 1090
Reset monitoring signals,
shaft rounds and angle
P2.2.7.30 Emergency stop 0 0.2 1213
P2.2.7.31 Master Follower mode 2 0 0.1 1092
P2.2.7.32
Input switch
acknowledgement
0 0.2 1209
Table 6-12. Digital input signals, G2.2.4
cc = closing contact
oc = opening contact
Automation and Control Solutions
Honeywell
Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North 35 Dynamic Drive
Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1
MIV 4Z9
www.honeywell.com