NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

More documents

Recommendations

Info

110 Pump and Fan Control Application Honeywell 7.5.3.4 Analogue input 3 (Control keypad: Menu M2 G2.2.4) Code Parameter Min Max Unit Default Cust ID Note P2.2.4.1 AI3 signal selection 0 0.1 141 P2.2.4.2 AI3 filter time 0,00 10,00 s 0,10 142 0=No filtering P2.2.4.3 AI3 signal range 0 2 1 143 0=0—20 mA 1=4—20 mA 2=Customised P2.2.4.4 AI3 custom minimum -160,00 setting 160,00 % 0,00 144 P2.2.4.5 AI3 custom maximum setting -160,00 160,00 % 100,00 145 P2.2.4.6 AI3 inversion 0 1 0 151 0=Not inverted 1=Inverted Table 7-7. Input signals, Analogue input 3 7.5.3.5 Analogue input 4, (Control keypad: Menu M2 G2.2.5) Code Parameter Min Max Unit Default Cust ID Note P2.2.5.1 AI4 signal selection 0 0.1 152 P2.2.5.2 AI4 filter time 0,00 10,00 s 0,10 153 0=No filtering P2.2.5.3 AI4 signal range 0 2 1 154 0=0—20 mA 1=4—20 mA 2=Customised P2.2.5.4 AI4 custom minimum setting -160,00 160,00 % 0,00 155 P2.2.5.5 AI4 custom maximum setting -160,00 160,00 % 100,00 156 P2.2.5.6 AI4 inversion 0 1 0 162 Table 7-8. Input signals, Analogue input 4 0=Not inverted 1=Inverted *Remember to place jumpers of block X2 accordingly. See the product's User's Manual Automation and Control Solutions Honeywell Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1 MIV 4Z9 www.honeywell.com
Honeywell Pump and Fan Control Application 111 7.5.3.6 Digital inputs (Control keypad: Menu M2 G2.2.4) Code Parameter Min Default Cust ID Note P2.2.6.1 Start A signal 0 A.1 423 P2.2.6.2 Start B signal 0 A.4 424 P2.2.6.3 Control place A/B Control place A (oc) 0 A.6 425 selection Control place B (cc) P2.2.6.4 External fault (close) 0 0.1 405 Ext. fault displayed (cc) P2.2.6.5 External fault (open) 0 0.2 406 Ext. fault displayed (oc) P2.2.6.6 Run enable 0 0.2 407 Motor start enabled (cc) P2.2.6.7 Acc/Dec time Acc/Dec time 1 (oc) 0 0.1 408 selection Acc/Dec time 2 (cc) P2.2.6.8 Control from I/O terminal 0 0.1 409 Force control place to I/O terminal (cc) P2.2.6.9 Control from keypad 0 0.1 410 Force control place to keypad (cc) P2.2.6.10 Control from fieldbus 0 0.1 411 Force control place to fieldbus (cc) P2.2.6.11 Reverse 0 0.1 412 Direction forward (oc) Direction reverse (cc) P2.2.6.12 Jogging speed 0 A.5 413 Jogging speed selected for frequency reference (cc) P2.2.6.13 Fault reset 0 0.1 414 All faults reset (cc) P2.2.6.14 Acc/Dec prohibit 0 0.1 415 Acc/Dec prohibited (cc) P2.2.6.15 DC braking 0 0.1 416 DC braking active (cc) P2.2.6.16 Motor potentiometer Mot.pot. reference 0 0.1 417 reference DOWN decreases (cc) P2.2.6.17 Motor potentiometer Mot.pot. reference 0 0.1 418 reference UP increases (cc) P2.2.6.18 Autochange 1 Interlock 0 A.2 426 Activated if cc P2.2.6.19 Autochange 2 Interlock 0 A.3 427 Activated if cc P2.2.6.20 Autochange 3 Interlock 0 0.1 428 Activated if cc P2.2.6.21 Autochange 4 0 0.1 429 Activated if cc P2.2.6.22 Interlock Autochange 5 Interlock 0 0.1 430 Activated if cc P2.2.6.23 PID reference 2 0 0.1 431 Table 7-9. Input signals, Digital inputs Selected with 2.1.11 (oc) Selected with 2.2.1.4 (cc) cc = closing contact oc = opening contact Automation and Control Solutions Honeywell Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MIN 55422 Scarborough, Ontario 63-2600-1 MIV 4Z9 www.honeywell.com
Page 1:
NX Series Constant and Variable Tor
Page 4 and 5:
CONTENTS NX USER’S MANUAL INDEX 1
Page 6 and 7:
NX User's Manual Index 1. SAFETY...
Page 8 and 9:
1 6(110) Safety 1. SAFETY ONLY A CO
Page 10 and 11:
8(110) DIRECTIVES 2. DIRECTIVES 2.1
Page 12 and 13:
10(110) DIRECTIVES We Manufacturer'
Page 14 and 15:
3 12(110) Receipt of shipment We Ma
Page 16 and 17:
3 14(110) Receipt of shipment 3.3 M
Page 18 and 19:
16(110) Technical data The control
Page 20 and 21:
18(110) Technical data 4.2.2 NX_6 -
Page 22 and 23:
20(110) Technical data 4.3 Brake re
Page 24 and 25:
22(110) Technical data 4.4 Technica
Page 26 and 27:
5 24(110) Installation 5. INSTALLAT
Page 28 and 29:
5 26(110) Installation W2 H4 D1 D2
Page 30 and 31:
5 28(110) Installation W4 W2 H7 H6
Page 32 and 33:
5 30(110) Installation Ø D1 D2 H4
Page 34 and 35:
5 32(110) Installation W4 Type plat
Page 36 and 37:
5 34(110) Installation 5.2 Cooling
Page 38 and 39:
5 36(110) Installation 5.3 Power lo
Page 40 and 41:
5 38(110) Cabling and connections 5
Page 42 and 43:
40(110) Cabling and connections 6.
Page 44 and 45:
42(110) Cabling and connections 6.1
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
52(110) Cabling and connections Fig
Page 56 and 57:
Page 58 and 59:
56(110) Cabling and connections Mai
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
64(110) Cabling and connections 10V
Page 68 and 69:
66(110) Cabling and connections OPT
Page 70 and 71:
68(110) Cabling and connections Jum
Page 72 and 73:
7 70(110) Control keypad 4 5 6 READ
Page 74 and 75:
7 72(110) Control keypad 7.2 Keypad
Page 76 and 77:
7 74(110) Control keypad RE ADY I/O
Page 78 and 79:
7 76(110) Control keypad 7.3.2 Para
Page 80 and 81:
7 78(110) Control keypad 7.3.3 Keyp
Page 82 and 83:
7 80(110) Control keypad NOTE! Ther
Page 84 and 85:
7 82(110) Control keypad 7.3.4.2 Fa
Page 86 and 87:
7 84(110) Control keypad 50 Analog
Page 88 and 89:
7 86(110) Control keypad 7.3.6 Syst
Page 90 and 91:
7 88(110) Control keypad T6.8.2.2 C
Page 92 and 93:
7 90(110) Control keypad STOP I/Ote
Page 94 and 95:
7 92(110) Control keypad Automatic
Page 96 and 97:
7 94(110) Control keypad Note! Stor
Page 98 and 99:
7 96(110) Control keypad Default pa
Page 100 and 101:
7 98(110) Control keypad READY READ
Page 102 and 103:
7 100(110) Control keypad STOP READ
Page 104 and 105:
7 102(110) Control keypad READY REA
Page 106 and 107:
7 104(110) Control keypad 7.4 Furth
Page 108 and 109:
106(110) Commissioning 6 Connect th
Page 110 and 111:
108(110) Fault tracing 9. FAULT TRA
Page 112:
110(110) Fault tracing 43 Encoder f
Page 115:
NX Series Constant and Variable Tor
Page 118 and 119:
2 Honeywell ABOUT THE "All in One"
Page 120 and 121:
4 Honeywell 9.1 External brake cont
Page 122 and 123:
6 Basic Application Honeywell 1.2 C
Page 124 and 125:
8 Basic Application Honeywell 1.4 B
Page 126 and 127:
10 Basic Application Honeywell 1.4.
Page 128 and 129:
12 Standard Application Honeywell 2
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
22 Local/Remote Control Application
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
36 Multi-step Speed Application Hon
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
48 PID Control Application Honeywel
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177: 60 PID Control Application Honeywel
Page 178 and 179: 62 Multi-purpose Control Applicatio
Page 212 and 213: 96 Pump and Fan Control Application
Page 214 and 215: 98 Pump and Fan Control Application
Page 216 and 217: 100 Pump and Fan Control Applicatio
Page 238 and 239: 122 Description of Parameters Honey
Page 276 and 277:
160 Description of Parameters Honey
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
210 Appendices Honeywell 9. APPENDI
Page 328 and 329:
212 Appendices Honeywell 9.2 Closed
Page 330:
Automation and Control Solutions Ho
show all

NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?