NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...
NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...
NXS Form 63-2600, Users Manual, Technical Data - CONTROL ...
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
74 Multi-purpose Control Application Honeywell<br />
6.6.4 Input signals<br />
6.6.4.1 Basic Settings (Control keypad: Menu M2 G2.2.1)<br />
Code Parameter Min Max Unit Default Cust ID Note<br />
Start signal<br />
1<br />
(Default:<br />
DIN1)<br />
Start<br />
signal 2<br />
(Default:<br />
DIN2)<br />
P2.2.1.1<br />
P2.2.1.2<br />
P2.2.1.3<br />
Start/Stop logic<br />
selection<br />
Motor potentiometer<br />
ramp time<br />
Motor potentiometer<br />
frequency reference<br />
memory reset<br />
0 7 0 300<br />
0,1 2000,0 Hz/s 10,0 331<br />
0 2 1 367<br />
P2.2.1.4 Adjust input 0 5 0 493<br />
P2.2.1.5 Adjust minimum 0,0 100,0 % 0,0 494<br />
P2.2.1.6 Adjust maximum 0,0 100,0 % 0,0 495<br />
Table 6-6. Input signals: basic settings, G2.2.1<br />
6.6.4.2 Analogue input 1 (Control keypad: Menu M2 G2.2.2)<br />
0<br />
1<br />
2<br />
3<br />
4<br />
5<br />
6<br />
7<br />
Start forw.<br />
Start/Stop<br />
Start/Stop<br />
Start pulse<br />
Start<br />
Fwd pulse<br />
Start pulse<br />
Start pulse<br />
Start rev.<br />
Reverse<br />
Run enable<br />
Stop pulse<br />
Mot.pot.UP<br />
Rev pulse<br />
Rev pulse<br />
Enabl pulse<br />
0=No reset<br />
1=Reset if stopped or<br />
powered down<br />
2=Reset if powered down<br />
0=Not used<br />
1=AI1<br />
2=AI2<br />
3=AI3<br />
4=AI4<br />
5=Fieldbus (FBProcess<strong>Data</strong>IN3)<br />
Code Parameter Min Max Unit Default Cust ID Note<br />
P2.2.2.1<br />
AI1 signal<br />
selection<br />
0 A.1 377<br />
P2.2.2.2 AI1 filter time 0,00 10,00 s 0,10 324 0=No filtering<br />
P2.2.2.3 AI1 signal range 0 3 0 320<br />
0=0…100%*<br />
1=20…100%*<br />
2= -10V…+10V*<br />
3= Custom range*<br />
P2.2.2.4<br />
AI1 custom minimum<br />
-160,00<br />
setting<br />
160,00 % 0,00 321<br />
P2.2.2.5<br />
AI1 custom<br />
maximum setting<br />
-160,00 160,00 % 100,00 322<br />
P2.2.2.6<br />
AI1 reference<br />
scaling, minimum<br />
value<br />
0,00 320,00 Hz 0,00 303<br />
Selects the frequency that<br />
corresponds to the min.<br />
reference signal<br />
P2.2.2.7<br />
P2.2.2.8<br />
AI1 reference<br />
scaling, maximum<br />
value<br />
AI1 joystick<br />
0,00 320,00 Hz 0,00 304<br />
0,00 20,00 % 0,00 384<br />
Selects the frequency that<br />
corresponds to the max.<br />
reference signal<br />
hysteresis<br />
P2.2.2.9 AI1 sleep limit 0,00 100,00 % 0,00 385<br />
P2.2.2.10 AI1 sleep delay 0,00 320,00 s 0,00 386<br />
P2.2.2.11 AI1 joystick offset -100,00 100,00 % 0,00 165<br />
Table 6-7. Analogue input 1 parameters, G2.2.2<br />
*Remember to place jumpers of block X2 accordingly.<br />
See the product's User's <strong>Manual</strong><br />
Automation and Control Solutions<br />
Honeywell<br />
Honeywell Limited-Honeywell Limitée<br />
1985 Douglas Drive North 35 Dynamic Drive<br />
Golden Valley, MIN 55422 Scarborough, Ontario <strong>63</strong>-<strong>2600</strong>-1<br />
MIV 4Z9<br />
www.honeywell.com
Change language