MaxSea Operator Manual version 12.6 - Furuno USA

More documents

Recommendations

Info

MaxSea Operator Manual version 12.6 SOG 438 Speed Over Ground - it is the actual fixed geographic speed of a vessel. It is essentially the Speed over Water (SOW), plus the cumulative effect of wind and current. ETA Estimation Time Arrival - Software calculation with present date and speed of the vessel. Current Dir Current Direction Current Speed Current Speed TWD TWS TWA True Wind Direction - In order to overcome the effects of drift and wind, a vessel which is trying to reach a given waypoint may not bear straight towards it. As a result, onboard wind direction measurements - the AWD - may not be the same as the True Wind Direction (TWD). True Wind Speed - When the vessel is in motion, onboard wind speed measurements - the AWS - will differ from stationary measurements (TWS). True Wind Angle AWA Apparent Wind Angle Software calculation with present date and speed..
AWS Apparent Wind Speed - When the vessel is in motion, onboard wind speed measurements - the AWS - will differ from stationary measurements (True Wind Speed, or TWS). Your product derives TWS from AWS by taking the vessel's motion into account. Leg Dist Leg Distance - distance between two waypoints. Tot Dist Total Distance - additional distance between the first waypoint and the last waypoint. Pos Geographical position drawn by a point on your chart. Weather Routing 439
Page 1:
MaxSea Operator Manual version 12.6
Page 4 and 5:
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12:
Page 15 and 16:
USER GUIDE: MaxSea New Faetures 3
Page 17 and 18:
User Interface Looking at the Chart
Page 19 and 20:
Toolbar Cursor Data User Interface
Page 21 and 22:
Notes: (1) - there is a display for
Page 23 and 24:
User Interface 2. To return to the
Page 25 and 26:
Bearing tool The Bearing tool is a
Page 27 and 28:
Select tool (Finger symbol) Lasso R
Page 29 and 30:
Plotting Drawing Type User Interfac
Page 31 and 32:
NavNet system MaxSea-NavNet Overvie
Page 33 and 34:
Legend (1) - GPS Antenna (2) - Rada
Page 35 and 36:
WARNING : NavNet system You have to
Page 37 and 38:
GPS on the chart Your GPS on the ch
Page 39 and 40:
2. Click the Misc tab for calling u
Page 41 and 42:
How to enable the Auto-Scale functi
Page 43 and 44:
GPS on the chart • Enter directly
Page 45:
GPS on the chart 1 - Click on the M
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 57 and 58:
Routes Routes overview A Route is a
Page 59 and 60:
(1) Route using QuickWaypoints, (2)
Page 61 and 62:
Routes Center All your Routes are d
Page 63 and 64:
Name To assign a own name of a rout
Page 65 and 66:
Fig. 1 shows you the selected Leg o
Page 67 and 68:
SOG SOW Speed Over Ground - it is t
Page 69 and 70:
XTE Cross Track Error - The distanc
Page 71 and 72:
Add Waypoints to a Route Additional
Page 73 and 74:
Reverse the Selected Route Routes W
Page 75 and 76:
more information, refer to the rela
Page 77 and 78:
Waypoints Waypoints Overview Waypoi
Page 79 and 80:
access and modify the properties of
Page 81 and 82:
displaying waypoint. modifiable. FI
Page 83 and 84:
Active Route Data Transfer Device O
Page 85 and 86:
On a selected waypoint drawn on the
Page 87 and 88:
Active Route Note: the software aut
Page 89 and 90:
Then choose [New Search and Rescue
Page 91 and 92:
Data Transfer Device Data Transfer
Page 93 and 94:
Note: Tracks (1) - According to the
Page 95 and 96:
NS = Not Supported Data Transfer De
Page 97 and 98:
Data Transfer Device - Rte valid na
Page 99 and 100:
Data Transfer Device - Wpt valid na
Page 101 and 102:
.ErrorChar : 0x\00 .EofChar : 0x\00
Page 103 and 104:
.Parity : 0 .StopBits : 0 .XonChar
Page 105 and 106:
.fRtsControl : 0 .fAbortOnError : 0
Page 107 and 108:
.XonChar : 0x\11 .XoffChar : 0x\13
Page 109 and 110:
- - - - - - - - - - - - - - - - - -
Page 111 and 112:
- MxDemandeStatutGPS : PNTI,000 ---
Page 113:
When GPS upload function is activat
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 123 and 124:
User's Data Adding personal marks U
Page 125 and 126:
User's Data The left part of the bo
Page 127 and 128:
Repeat the operation, changing the
Page 129 and 130:
User's Data You can either display
Page 131 and 132:
User's Data 3. Type in your text (6
Page 133 and 134:
3 - to delete the mark. 4 - to sele
Page 135 and 136:
User's Data Using the Position modi
Page 137 and 138:
User's Data To do this, first selec
Page 139 and 140:
6. Closing user's data layer file (
Page 141 and 142:
Drawing layer's catalog All drawing
Page 143 and 144:
(2) - only the layers modified sinc
Page 145 and 146:
Note: in case of a bad version or a
Page 147 and 148:
• The AutoCAD file has to respect
Page 149 and 150:
User's Data Plotting and modificati
Page 151 and 152:
Electronic Charts Electronic Charts
Page 153 and 154:
4 - the chart is opened and display
Page 155 and 156:
Electronic Charts IMPORTANT - Each
Page 157 and 158:
2 - Using the "Zoom in" and "Zoom o
Page 159 and 160:
Downstair left-hand corner window c
Page 161 and 162:
Electronic Charts The chart is show
Page 163 and 164:
W000 / W003 Electronic Charts IMPOR
Page 165 and 166:
Electronic Charts Specific items ac
Page 167 and 168:
019 Arc 1950 -- Malawi 020 Arc 1950
Page 169 and 170:
086 Kertau 1948 -- West Malaysia &
Page 171 and 172:
151 Provisional S. American 1956 --
Page 173 and 174:
2 - The chart data display depends
Page 175 and 176:
Mapmedia mm2 Charts Electronic Char
Page 177 and 178:
Electronic Charts 3. Chart File Not
Page 179 and 180:
Electronic Charts The chart which w
Page 181 and 182:
Electronic Charts To obtain informa
Page 183 and 184:
Opening a M.C. Pack Chart file Elec
Page 185 and 186:
The Status allows the user to know
Page 187 and 188:
Tips Electronic Charts The Chart Zo
Page 189 and 190:
Following list shows available C-Ma
Page 191 and 192:
Note: to order C-MAP NT/PC refer to
Page 193 and 194:
To display an own configuration: 1.
Page 195 and 196:
C-Map NT Chart Object Properties Yo
Page 197 and 198:
Closing C-Map NT chart Electronic C
Page 199 and 200:
CMAP NT CMap CM93 v3 Geographic Gri
Page 201 and 202:
• Other in standard S52. • S52
Page 203 and 204:
Electronic Charts The "Change Confi
Page 205 and 206:
Electronic Charts Anchorage area (a
Page 207 and 208:
GP_PARAM_ID_PLAIN_DEPCNT GP_PARAM_I
Page 209 and 210:
Weather Forecast Weather overview M
Page 211 and 212:
2. save it to your computer • Cli
Page 213 and 214:
Weather Forecast 1. click and drag
Page 215 and 216:
Wind feather : For wind information
Page 217 and 218:
06 09 : 13 Jan. 18. -06 01 : 00 Sel
Page 219 and 220:
• Second number (00s). Note : 1 h
Page 221 and 222:
(see Register to MaxSea Chopper cha
Page 223 and 224:
• To receive Select Subscribe to
Page 225 and 226:
Pressure Global (with Inland) 1°x1
Page 227 and 228:
Geopotential Height Global (with In
Page 229 and 230:
Tides and Tidal Currents Tides and
Page 231 and 232:
• Use the right-click menu on sel
Page 233 and 234:
The tidal height function is used t
Page 235 and 236:
Tides and Tidal Currents Arrows bec
Page 237 and 238:
Tides and Tidal Currents Note for e
Page 239 and 240:
When you choose to display this win
Page 241 and 242:
2D Bathymetric Maps 2D Bathy Maps W
Page 243 and 244:
IMPORTANT 2D Bathymetric Maps MaxSe
Page 245 and 246:
IMPORTANT Display only User data 2D
Page 247 and 248:
The configuration is simultaneously
Page 249 and 250:
Overlaying simultaneously several t
Page 251 and 252:
2D Bathymetric Maps Here the "isoba
Page 253 and 254:
3D Bathymetric database 3D Bathymet
Page 255 and 256:
3D Database Import Import data to M
Page 257 and 258:
By choosing in the first zone area
Page 259 and 260:
Click on "Open" and the file path w
Page 261 and 262:
User comments [PARAMETERS] HeightUn
Page 263 and 264:
Note: 1. To add several user data f
Page 265 and 266:
3D Bathymetric database • Before
Page 267 and 268:
BE CAREFUL: this operation can take
Page 269 and 270:
How to configure the Offset Data Im
Page 271 and 272:
Then choose a station from the harb
Page 273 and 274:
MaxSea allows to display independen
Page 275 and 276:
See also related topics: 1. Modify
Page 277 and 278:
Correct value representation First
Page 279 and 280:
After you have chosen the option se
Page 281 and 282:
To do it select [Manage 3D database
Page 283 and 284:
Repair the 3D database MaxSea verif
Page 285:
Archived 3D Database What means arc
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 319 and 320:
Trawl Positioning Dead Reckoning Tr
Page 321 and 322:
ofile Contour Depth Profile Contour
Page 323 and 324:
2. Click on "Trawl" . 3. Select the
Page 325 and 326:
Description: 1 - DAP1 and DAP2 foll
Page 327 and 328:
dY = Horizontal distance from the t
Page 329 and 330:
Dredge Function Dredge Function Ove
Page 331 and 332:
Dredge Quality Inactive dredge (Qua
Page 333 and 334:
Sounder Depth Profile Depth Profile
Page 335 and 336:
4 - Historic Mode • Plot "Events"
Page 337 and 338:
file NavNet (1) HF/LF axSea Mode Na
Page 339 and 340:
Shift level m (maximal value for R+
Page 341 and 342:
Sounder Depth Profile 2. You may sp
Page 343 and 344:
Fig.1 : Représentation du profil d
Page 345 and 346:
MaxSea Depth Profile User Interface
Page 347 and 348:
Scale + Scale - Exaggeration Exagge
Page 349 and 350:
Depth Profile Outline is only depen
Page 351 and 352:
ID Information (1) (2) (3) (4) Disp
Page 353 and 354:
Sounder Depth Profile Fig.1 : Depth
Page 355 and 356:
Enter an event to plot fish schools
Page 357 and 358:
A-scope Sounder Depth Profile • C
Page 359 and 360:
Temperature Graph displayed with Na
Page 361 and 362:
Targets Targets Overview MaxSea sha
Page 363 and 364:
Targets The "Center on" function is
Page 365 and 366:
5. Erase the selected target from t
Page 367 and 368:
Display Position at CPA: TCPA : Tim
Page 369 and 370:
Automatically Tracking Targets The
Page 371 and 372:
IMPORTANT Note : the Target Center
Page 373 and 374:
Note that this item may be disable
Page 375 and 376:
ARPA's Target Symbol To display the
Page 377 and 378:
How to configure AIS system with Ma
Page 379 and 380:
Using the Select point tool double
Page 381 and 382:
Note: the static Data are integrate
Page 383 and 384:
EXTRA IO port : outputs AIS entence
Page 385 and 386:
Input / Output of AIS signal Target
Page 387 and 388:
Buoy's Target Symbol Activating the
Page 389 and 390:
Activating the Fleet tracking To ac
Page 391 and 392:
Radar OVERLAY Radar Overlay Overvie
Page 393 and 394:
Gain Status Gain AC Sea Transmit Ma
Page 395 and 396:
AC Sea Level AC Auto On - Off AC Ra
Page 397 and 398:
Radar / Chart Offset Direction 0-36
Page 399 and 400: may be missed. FTC % 0-100 To adjus
Page 401 and 402: 6 minutes 12 minutes Setting Up FUR
Page 403 and 404: Gain AC Sea AC Rain Radar Source Me
Page 405 and 406: Display Option Range Operation Echo
Page 407 and 408: Noise Rejection Tune Auto/Manual Tu
Page 409 and 410: To center on the chart in the radar
Page 411 and 412: When the Minimum or Maximum Range i
Page 413 and 414: Acquiring Radar Targets Acquiring R
Page 415: To Free a Radar Target Radar OVERLA
Page 418 and 419: MaxSea Operator Manual version 12.6
Page 453 and 454: Professional Weather Routing What i
Page 455 and 456: At this moment the routing will sto
Page 457 and 458: Professional Weather Routing Once t
Page 459 and 460: Professional Weather Routing 4 - al
Page 461 and 462: Launch a new Route plan Refer to th
Page 463: Professional Weather Routing The re
Page 500 and 501:
Page 502 and 503:
Page 504 and 505:
Page 506 and 507:
Page 508 and 509:
Page 510 and 511:
Page 512 and 513:
Page 514 and 515:
Page 517 and 518:
Glossary A ACK: Acknowledge ACQ: Ac
Page 519 and 520:
Glossary DDE: Dynamic Data Exchange
Page 521 and 522:
Glossary Manual activation email: I
Page 523:
U Glossary UDP: User Datagram Proto
Page 526 and 527:
Page 528 and 529:
show all

MaxSea Operator Manual version 12.6 - Furuno USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?