E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

More documents

Recommendations

Info

Using the Key Protect Level Section 4-9 4-9 Using the Key Protect Level 4-9-1 Protection Operation/Adjustment Protect oapt 0 Initial Setting/ Communications Protect icpt 0 Setting Change Protect wtpt off 106 To move to the protect level, press the O and M Keys simultaneously for at least three seconds in operation level or adjustment level. (See note.) Note The key pressing time can be changed in the Move to Protect Level Time parameter (advanced function setting level). The protect level protects parameters that are not changed during Controller operation until operation is started to prevent them from being modified unintentionally. There are four types of protection: operation/adjustment protect, initial setting/communications protect, setting change protect, and PF Key protect. The protect level settings restrict the range of parameters that can be used. The following table shows the relationship between set values and the range of protection. Level Set value 0 1 2 3 Operation level Parameters are not protected when the set value is set to 0. The default is 0. This protect level restricts movement to the initial setting level, communications setting level, and advanced function setting level. The default is 0. PV Can be displayed PV/SP Can be displayed and changed Others Can be displayed and changed Adjustment level Can be displayed and changed Set value Can be displayed Can be displayed and changed Can be displayed and changed Cannot be displayed and moving to other levels is not possible Initial setting level Communications setting level Can be displayed Can be displayed and changed Cannot be displayed and moving to other levels is not possible Cannot be displayed and moving to other levels is not possible Can be displayed Can be displayed Cannot be displayed and moving to other levels is not possible Cannot be displayed and moving to other levels is not possible Advanced function setting level 0 Possible to reach Possible to reach Possible to reach 1 Possible to reach Possible to reach Not possible to reach 2 Not possible to reach Not possible to reach Not possible to reach This protect level restricts key operations. Set value Description OFF Settings can be changed using key operations. ON Settings cannot be changed using key operations. (The protect level settings, however, can be changed.)
Using the Key Protect Level Section 4-9 The default is OFF. The all protect indication ( ) will light when setting change protect is set. PF Key Protect This protect level enables or disables PF Key operations. pfpt off Set value OFF PF Key enabled. Description The default is OFF. 4-9-2 Entering the Password to Move to the Protect Level Protect level can be moved to only by display the password display and entering the correct password. (The user can set any password in the Protect Level Password parameter. If no password is set (i.e., if the password is set to 0 in the Protect Level Password parameter), the password input display to move to protect level will not be displayed and the protect level can be moved to directly. Operating Procedure Use the following procedure to move to protect level. Operation Level C ON PF Key disabled (Operation as function key prohibited). ■ Example with a Password of 1234 Protect Level 1. Press the O and M Keys simultaneously for at least the time set in the Move to Protect Level Time parameter to move from the operation level to the protect level. 2. Press the U Key to set the parameter to 1234 (password input). Protect Level 3. Move to the Operation/Adjustment Protect parameter by pressing the O Operation/Adjustment Protect or M Key or leaving the setting for at least two seconds. Operation Level C 25.0 100.0 pmov 0 pmov 1234 oapt 0 25.0 100.0 PV/SP Move to Protect Level ■ Example with No Password Set Protect Level Press the O and M Keys simultaneously for at least the time set in the oapt 0 PV/SP Operation/Adjustment Protect Operation/Adjustment Protect parameter to move from the operation level to the protect level. When a password is not set, the Operation/Adjustment Protect parameter will be displayed. 107
Page 1:
SUB1 SUB2 SUB3 HA OUT1 STOP OUT2 CW
Page 5 and 6:
Preface The E5CN-H, E5AN-H, and E5E
Page 7 and 8:
Disclaimers CHANGE IN SPECIFICATION
Page 9 and 10:
■ Safety Precautions CAUTION Do n
Page 11 and 12:
Precautions for Safe Use Be sure to
Page 13 and 14:
● Ensuring Measurement Accuracy W
Page 15 and 16:
Power supply ● Ferrite Core Conne
Page 17 and 18:
Conventions Used in This Manual Mea
Page 19 and 20:
TABLE OF CONTENTS SECTION 1 Introdu
Page 21 and 22:
About this Manual: This manual desc
Page 23 and 24:
SECTION 1 Introduction This section
Page 25 and 26:
Names of Parts Section 1-1 E5EN-H 1
Page 27 and 28:
I/O Configuration and Main Function
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Setting Level Configuration and Key
Page 35 and 36:
Setting Level Configuration and Key
Page 37 and 38:
Communications Function Section 1-4
Page 39 and 40:
SECTION 2 Preparations This section
Page 41 and 42:
Installation Section 2-1 2-1-2 Pane
Page 43 and 44:
Installation Section 2-1 2-1-3 Moun
Page 45 and 46:
Installation Section 2-1 Mounting t
Page 47 and 48:
Installation Section 2-1 E5AN/EN-H
Page 49 and 50:
Installation Section 2-1 1,2,3... 1
Page 51 and 52:
Wiring Terminals Section 2-2 E5AN/E
Page 53 and 54:
Wiring Terminals Section 2-2 Contro
Page 55 and 56:
Wiring Terminals Section 2-2 Take c
Page 57 and 58:
Wiring Terminals Section 2-2 Take c
Page 59 and 60:
Wiring Terminals Section 2-2 CT Inp
Page 61 and 62:
Wiring Terminals Section 2-2 RS-232
Page 63 and 64:
Using the Support Software Port Sec
Page 65 and 66:
Using Infrared Communications Secti
Page 67 and 68:
SECTION 3 Basic Operation This sect
Page 69 and 70:
Initial Setting Examples Section 3-
Page 71 and 72:
Setting the Input Type Section 3-2
Page 73 and 74:
Selecting the Temperature Unit Sect
Page 75 and 76:
Setting Output Specifications Secti
Page 77 and 78: Setting Output Specifications Secti
Page 79 and 80: Using ON/OFF Control Section 3-7 To
Page 81 and 82: Using ON/OFF Control Section 3-7 In
Page 83 and 84: Determining PID Constants (AT, ST,
Page 89 and 90: Alarm Outputs Section 3-9 2.d 45.0
Page 91 and 92: Alarm Outputs Section 3-9 3-9-2 Ala
Page 93 and 94: Using Heater Burnout, Heater Short,
Page 105 and 106: Setting the No. 3 Display Section 3
Page 107 and 108: SECTION 4 Applications Operations T
Page 109 and 110: Shifting Input Values Section 4-1 4
Page 111 and 112: Shifting Input Values Section 4-1 F
Page 113 and 114: Alarm Hysteresis Section 4-2 For ex
Page 115 and 116: Executing Heating/Cooling Control S
Page 117 and 118: Executing Heating/Cooling Control S
Page 119 and 120: Using Event Inputs Section 4-5 Cont
Page 121 and 122: Using Event Inputs Section 4-5 Cont
Page 123 and 124: Setting the SP Upper and Lower Limi
Page 125 and 126: Using the SP Ramp Function to Limit
Page 127: Moving to the Advanced Function Set
Page 131 and 132: PV Change Color Section 4-10 4-10 P
Page 133 and 134: PV Change Color Section 4-10 colr r
Page 135 and 136: Alarm Delays Section 4-11 Note (1)
Page 137 and 138: Loop Burnout Alarm Section 4-12 Par
Page 139 and 140: Loop Burnout Alarm Section 4-12 Ini
Page 141 and 142: Performing Manual Control Section 4
Page 147 and 148: Using the Transfer Output Section 4
Page 149 and 150: Using the Transfer Output Section 4
Page 151 and 152: Using Banks and PID Sets Section 4-
Page 153 and 154: Using Banks and PID Sets Section 4-
Page 155 and 156: Using the Simple Program Function S
Page 163 and 164: Output Adjustment Functions Section
Page 165 and 166: Output Adjustment Functions Section
Page 167 and 168: Using the Extraction of Square Root
Page 169 and 170: Setting the Width of MV Variation S
Page 171 and 172: Setting the PF Key Section 4-20 Set
Page 173 and 174: Counting Control Output ON/OFF Oper
Page 175 and 176: Displaying PV/SV Status Section 4-2
Page 177 and 178: Using a Remote SP Section 4-23 4-23
Page 179 and 180:
Position-proportional Control Secti
Page 181 and 182:
Logic Operations Section 4-25 Manua
Page 183 and 184:
Logic Operations Section 4-25 Examp
Page 185 and 186:
Logic Operations Section 4-25 4. Se
Page 187 and 188:
Logic Operations Section 4-25 11. C
Page 189 and 190:
Logic Operations Section 4-25 Opera
Page 191 and 192:
This section describes the individu
Page 193 and 194:
Protect Level Section 5-2 5-2 Prote
Page 195 and 196:
Protect Level Section 5-2 wtpt Sett
Page 197 and 198:
Operation Level Section 5-3 5-3 Ope
Page 199 and 200:
Operation Level Section 5-3 Functio
Page 201 and 202:
Operation Level Section 5-3 bank Ba
Page 203 and 204:
Operation Level Section 5-3 ct1 Hea
Page 205 and 206:
Operation Level Section 5-3 lcr1 Le
Page 207 and 208:
Operation Level Section 5-3 r-s RUN
Page 209 and 210:
Operation Level Section 5-3 al1h Al
Page 211 and 212:
Operation Level Section 5-3 See ■
Page 213 and 214:
Adjustment Level Section 5-4 Adjust
Page 215 and 216:
Adjustment Level Section 5-4 cmwt C
Page 217 and 218:
Adjustment Level Section 5-4 See
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Adjustment Level Section 5-4 c-sc C
Page 225 and 226:
Adjustment Level Section 5-4 soak S
Page 227 and 228:
Adjustment Level Section 5-4 sprt S
Page 229 and 230:
Adjustment Level Section 5-4 db Pos
Page 231 and 232:
Bank Setting Level Section 5-5 5-5
Page 233 and 234:
Bank Setting Level Section 5-5 See
Page 235 and 236:
Bank Setting Level Section 5-5 Sett
Page 237 and 238:
Bank Setting Level Section 5-5 *.so
Page 239 and 240:
PID Setting Level Section 5-6 *.p P
Page 241 and 242:
PID Setting Level Section 5-6 *.csc
Page 243 and 244:
Manual Control Level Section 5-8 5-
Page 245 and 246:
Initial Setting Level Section 5-9 5
Page 247 and 248:
Initial Setting Level Section 5-9 S
Page 249 and 250:
Initial Setting Level Section 5-9 s
Page 251 and 252:
Page 253 and 254:
Initial Setting Level Section 5-9 o
Page 255 and 256:
Initial Setting Level Section 5-9 a
Page 257 and 258:
Initial Setting Level Section 5-9 t
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Initial Setting Level Section 5-9 a
Page 265 and 266:
Advanced Function Setting Level Sec
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Communications Setting Level Sectio
Page 305 and 306:
This section describes how the user
Page 307 and 308:
User Calibration Section 6-2 6-2 Us
Page 309 and 310:
Thermocouple Calibration (Thermocou
Page 311 and 312:
Platinum Resistance Thermometer Cal
Page 313 and 314:
Calibrating Analog Input (Analog In
Page 315 and 316:
Calibrating the Transfer Output Sec
Page 317 and 318:
Checking Indication Accuracy Sectio
Page 319 and 320:
Specifications Ratings Appendix Sup
Page 321 and 322:
Proportional band (P) Temperature I
Page 323 and 324:
E54-CT3 40 × 40 30 30 12 dia. 9 Tw
Page 325 and 326:
E58-CIFIR USB-Infrared Conversion C
Page 327 and 328:
Appendix Action Control continues,
Page 329 and 330:
Troubleshooting Appendix Checking P
Page 331 and 332:
Symptom: Cannot Communicate or a Co
Page 333 and 334:
Parameter Operation Lists Operation
Page 335 and 336:
Proportional Band (See note 1.) Int
Page 337 and 338:
Bank Setting Level Appendix Paramet
Page 339 and 340:
PID Setting Level Appendix Paramete
Page 341 and 342:
Scaling Upper Limit in-h Scaling lo
Page 343 and 344:
Transfer Output Lower Limit Linear
Page 345 and 346:
Auxiliary Output 1 Open in Alarm Au
Page 347 and 348:
Control Output 1 Assignment out1 Wh
Page 349 and 350:
Appendix Parameters Characters Sett
Page 351 and 352:
Note (1) The parameters in the curr
Page 353 and 354:
Related initialized parameters Rela
Page 355 and 356:
Changed parameter Related initializ
Page 357 and 358:
Appendix Sensor Input Setting Range
Page 359 and 360:
(4) When the PF Setting parameter i
Page 361 and 362:
c l.adj M at AT Execute/Cancel off
Page 363 and 364:
Protect Level Press the O Key for a
Page 365 and 366:
Numerics 2-PID control, 51, 228 A a
Page 367 and 368:
L LBA (loop burnout alarm), 114 ban
Page 369 and 370:
MV display, 250 MV display selectio
Page 371 and 372:
U universal inputs, 284 up key, 4 U
Page 373:
Revision History A manual revision
Page 376:
OMRON ELECTRONICS LLC • THE AMERI
show all

E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

Create successful ePaper yourself

Delete template?

Save as template?